Talento Automatic Coffee Machine Programming Instructions

KoffeeOne
96 followers
Apr 17, 2025
Talento Automatic Coffee Machine Programming Instructions
www.koffeeone.com.au
programming and calibration
introduction
when you enter the programming mode you
have access to all of the functions in
user and service engineer modes
programming
with the machine
off hold down the on off key for about 5
seconds until the display shows the
first programming function language
select
the keys to be used in the programming
stages are
enter to enter menus and or confirm
settings
the up and down arrow keys to scroll
through the menu
and increase decrease settings
and the reset button to return to the
previous step
the keys are also numbered from 1 to 10
as shown in the picture
user mode
functions once in programming mode press
enter and the display will read language
select
the only user mode function
it's sufficient to press the up arrow to
set the machine and the operator
interface language that will appear on
the display
the available languages are english
italian french german and spanish
service engineer mode functions to
access the programmable functions in
service engineer mode from the language
select mode
press the up arrow key and then the
display will show the message password
enter the standard password
times the grinder left key
counters
with the machine off press and hold down
the on off key for about five seconds
until the display shows the first
programming function language select
press the up arrow key enter the
standard password
four times the grinder left key
and the display will read
counters press enter to open the sub
menu
beverage counter
press enter to open the sub menu
all of the beverage keys 1 to 10 will
flash
press the beverage key to read the
number of beverages poured
press and hold down the enter key for 6
seconds to reset the counter
press the reset key to quit the selected
beverage counter
and then press reset again for three
seconds to quit the submenu
counters are updated every time a
beverage is poured
even if terminated manually by the
operator before the time limit envisaged
for the programmed dose
the increase is one for single beverages
and two for double ones
press the up arrow key to
continue total beverages
press enter to open the sub menu
all of the beverage keys 1 to 10 will
flash
press the beverage key to read the
number of beverages poured
press and hold down the enter key for 6
seconds to reset the counter
press the reset key to quit the submenu
the counter counts both grinders and the
increase is one for single beverages and
two for double ones
press the up arrow key to continue
cycle counter
press enter to open the submenu
all of the beverage keys 1 to 10 will
flash
press the beverage key to read the
number of beverages poured
the cycles refer to single beverages
press the two times key to see the
number of cycles for double beverages
press and hold down the enter key for
six seconds to reset the counter
press the reset key to quit the selected
beverage counter
and then press reset again for 3 seconds
to quit the sub menu
press the up arrow key to continue
total cycles
press enter to open the submenu
the display will read total cycles
the number of cycles is the sum of all
beverages single and double
press and hold down the enter key for 10
seconds to read the absolute total which
cannot be reset
press and hold down the enter key for 6
seconds to reset the partial total
cycles counter
press the reset key to quit the submenu
the keys will go back to fixed
press the up arrow key to continue
right grinder total
press enter to open the submenu
press and hold down the enter key for 10
seconds to read the absolute total which
cannot be reset
press and hold down the enter key for
eight seconds from the absolute total
menu to reset the right grinder total
counter
press the reset key to quit the sub menu
press the up arrow key to continue
left grinder total
press enter to open the sub menu
press and hold down the enter key for 10
seconds to read the absolute total which
cannot be reset
press and hold down the enter key for 6
seconds from the absolute total menu to
reset the left grinder total counter
press the reset key to quit the sub menu
press the up arrow key to continue
hot water total
press enter to open the submenu
press and hold down the enter key for 10
seconds to read the absolute total which
cannot be reset
press and hold down the enter key for 6
seconds from the absolute total menu to
reset the hot water total counter
press the reset key to quit the submenu
press the up arrow key to continue
steam total
press enter to open the submenu and read
the pouring time number
press and hold down the enter key for 10
seconds to read the absolute total which
cannot be reset
press and hold down the enter key for 6
seconds from the absolute total menu to
reset the steam tot counter
press the reset key to quit the submenu
press the up arrow key to continue
total liters
press enter to open the submenu
press and hold down the enter key for 10
seconds
to read the absolute total which cannot
be reset
press and hold down the enter key for 6
seconds from the absolute total menu to
reset the total liters
press the reset key to quit the sub menu
press the up arrow key to continue
total wash cycles
press enter to open the submenu
the display will read total washes
press and hold down the enter key for 10
seconds to read the absolute total which
cannot be reset
press and hold down the enter key for 6
seconds from the absolute total menu to
reset the total wash's counter
press the reset key to quit the sub-menu
press the reset key again to quit the
sub-menus
save data
to quit the menu push the up arrow key
until it reaches the menu save data
press enter key to confirm
dose programming
with the machine off press and hold down
the on off key for about 5 seconds until
the display shows the first programming
function language select
press the up arrow key enter the
standard password
four times the grinder left key and
press the up arrow key until the display
reads dose programming
this function serves to program each key
with the preferred beverage
press the enter key to enter the submenu
and select the key to be programmed
using the up and down arrow keys
the keys are numbered from 1 to 10.
press enter again to enter the function
programming mode for the individual key
use the up and down arrow keys to select
the required beverage
with off the key is disabled
coffee selects the coffee cycle
with milk coffee being the milk cycle
plus coffee cycle
and coffee milk the coffee cycle plus
milk with latte the milk and coffee
cycles together
with macchiato the milk cycle plus pours
three seconds plus coffee with milk the
milk cycle with tea
recycle hot water from the t1 with steam
man the cycle timer steam and with auto
steam the cycle steam set by temperature
press enter to confirm the required
beverage
the list of programmable functions for
the coffee beverage involves
grinding time
it's possible to set the grinding time
in seconds and therefore the amount of
ground coffee used
press enter to open the submenu use the
up down arrow keys to increase reduce
grinding time
press enter to confirm the setting
default grinder selection
it's possible to set a default grinder
left sx or right dx
press enter to open the submenu use the
up down arrow keys to select the right
or left grinder
press enter to confirm the setting
water volume
it's possible to set the volume of the
water for each coffee in ccs
press enter to open the submenu
use the up down arrow keys to increase
decrease the volume of water
press enter to confirm the setting
pre-infusion time
it's possible to set the pre-infusion
time in seconds
press enter to open the sub-menu
use the up down arrow keys to increase
decrease the pre-infusion time
press enter to confirm the setting
tamping
tamping can be enabled or disabled
press enter to open the submenu use the
up down arrow keys to select yes or no
to enable or disable pressing
press enter to confirm the setting
add water
it's possible to set the quantity of hot
water added to the coffee product
the list of programmable functions for
the milk coffee beverage includes
milk time
it's possible to set the time and
therefore the amount of milk
press enter to open the submenu use the
up down arrow keys to increase decrease
the time and therefore the amount of
milk
press enter to confirm the setting
air time disabled
it's possible to set the part of the
total milk time in which the air
solenoid valve remains shut so as to
regulate the amount of foam in the milk
press enter to open the submenu
use the up down arrow keys to increase
decrease the mill time during which the
solenoid is closed
press enter to confirm the setting
milk pipe auto wash
it's possible to set the cold water wash
time at the end of milk pouring
operations
press enter to open the submenu
use the up down arrow keys to increase
decrease washing time
press enter to confirm the setting
the following settings are the same as
the coffee cycle
double dose programming
used to program the double dose
after entering the menu for the required
key
press the required key and it will be
possible to program the very same list
of functions for the double dose
hot water
select the desired button and press
enter
press up arrow key in the cycle menu and
select the t cycle
press enter key to open the menu
use the up down arrow keys to increase
decrease the time
and therefore the amount of hot water
press enter to confirm the setting
steam man
select the desired button and press
enter
press up arrow key in the cycle menu and
select the steam man cycle
press enter key to open the menu
use the up down arrow keys to increase
decrease the time and therefore the
amount of steam
press enter to confirm the setting
auto steam
select the desired button and press
enter
press up arrow key in the cycle menu and
select the auto steam cycle
press enter key to open the menu
use the up down arrow keys to increase
decrease the temperature that has to
reach the beverage that you want to heat
up
press enter to confirm the setting
press up arrows until save data to quit
the menu
press enter to save the data
settings
with the machine off press and hold down
the on off key for about five seconds
until the display shows the first
programming function
language select
press the up arrow key enter the
standard password four times the grinder
left key
and press the up arrow key until the
display reads settings
temperature unit selection
it's possible to program the unit of
measurement for viewing the temperature
celsius or fahrenheit
press enter to open the submenu
the up down arrow keys can then be used
to select the preferred unit of
measurement celsius or fahrenheit
press enter to confirm the setting
press the up arrow key to proceed to the
next item
coffee boiler tank temperature
it's possible to program the temperature
of the water in the coffee boiler tank
press enter to open the submenu the up
down arrow keys serve to increase or
decrease the temperature of the water in
the coffee boiler tank minimum 80
degrees celsius maximum 100 degrees
celsius the recommended setting is 94
degrees
press enter to confirm the setting press
the up arrow key to proceed to the next
item
steam boiler tank temperature
it's possible to program the steam
temperature inside the service boiler
tank
press enter to open the submenu the up
down arrow keys serve to increase or
decrease the temperature of the steam in
the services boiler tank
minimum 80 degrees celsius maximum 140
degrees celsius the recommended setting
is 130 degrees
press enter to confirm the setting
press the up arrow key to proceed to the
next item
pouring group temperature
it's possible to program the temperature
of the pouring group
press enter to open the submenu
the up down arrow keys serve to increase
decrease the temperature of the pouring
group
minimum 80 degrees celsius maximum 105
degrees celsius
in one degree steps
the recommended setting is 94 degrees
press enter to confirm the setting
press the up arrow key to proceed to the
next item
ground draw
it's possible to program the number of
cycles after which it's necessary to
empty out the grounds draw
press enter to open the submenu
the up down arrow keys serve to select
the option withdraw or with direct
grounds discharge
press enter to open the submenu
the up down arrow keys are used to
increase or decrease the number of
cycles
minimum 1 maximum 40 for the option
withdraw
recommended setting 30
minimum 50 maximum no limit for the
option with direct discharge
press enter to confirm the setting
to reset the cycle count for emptying
the ground drawer pull the drawer out
for at least 15 seconds
press the up arrow key to proceed to the
next item washing cycle
it's possible to program a complete or
just a group washing cycle
press enter to open the submenu
the up down arrow keys serve to select
the complete washing cycle
recommended for machines with cappuccino
maker or group washing cycle recommended
for machines without cappuccino maker
but with auto steam
press enter to confirm the setting
each time that the washing cycle is
enabled it will follow the parameters
set in this function
washing alarm times
it's possible to program four times for
enabling the washing alarm
press enter to open the submenu
the up down arrow keys serve to select
the time to be set
for example time 1 press enter to open
the sub menu
the up down arrow keys serve to select
the hour and minutes at which the
washing alarm needs to appear
press enter and the up down arrow keys
to set the hour and minutes
press enter to confirm the setting
press reset to enable other washing
times
the display will read washing at the set
time or times this message will
disappear once washing has been
completed
if the times 1 2 3 4 functions are set
to hour 0 0 and minutes 0 0 the alarm is
deactivated
washing alarm cycles press enter to open
the submenu
this programs the number of cycles after
which the warning to clean the group
will be displayed
the up down arrow keys serve to increase
or decrease the number of cycles before
the group cleaning message is displayed
minimum 50 maximum no limit
press enter to confirm the setting
milk washing alarm
press enter to open the submenu
this programs the number of hours from
the last milk beverage being poured
after which the message to clean the
cappuccino maker is displayed
the up down arrow keys serve to increase
or decrease the number of hours before
the message to clean the cappuccino
maker is displayed
minimum no limit maximum 12 hours
press enter to confirm the setting
sequential heating
press enter to open the submenu
the up down arrow keys serve to enable
or disable a sequential heating function
yes no
with the sequential heating function
enabled yes the control unit will first
heat the coffee heating element and then
the services element power absorption is
2800 watts
with the sequential heating function
disabled no the control unit will heat
the two boilers at the same time
power absorption will be 5600 watts
programming automatic switch on off
this programs the automatic on off for
the machine
the default setting is that every day of
the week the machine is set to standby
and therefore to switch the machine on
or off it's necessary to use the on off
button
press enter to open the submenu and the
display will show the message monday the
up down arrow keys serve to view the
settings for each day of the week press
enter to set the required day of the
week
the up down arrow keys serve to select
the hour
and minutes for switching off
press enter to confirm the setting
the arrow keys can then be used to set
all the other days of the week
press the reset key to quit the submenu
energy saving
it's possible to enable disable the
energy saving function
press enter to open the submenu
the up down arrow keys serve to select
yes or no to enable or disable energy
saving mode
if enabled yes the machine will be
switched off manually or automatically
when the temperature of the boiler tank
drops below 80 degrees celsius for the
coffee boiler tank and 100 degrees
celsius for the steam tank
press enter to confirm the setting
then press reset to quit the submenu
group rinse it's possible to program the
standby time after which the machine
will carry out a group rinse cycle using
just water to keep the coffee circuit
clean and also hot
press enter to open the submenu
up down arrow keys serve to select off 5
10 20 40.
press enter to confirm the setting and
then press reset to quit the submenu
date time this programs the date and
time hour and minutes shown on the
machine display
press enter to open the submenu
the up down arrow keys serve to select
the required date
press enter to confirm use the up down
arrow keys to select the hour and minute
press reset to quit the submenu
steam option
it's possible to set the steam option
desired
press enter to open the submenu
the up down arrow keys serve to select
the steam engine
disable
steam man time esteem auto steam
press enter to confirm
t option
it's possible to set the t option
desired
press enter to open the submenu
the up down arrow keys serve to select
the t option
disable or enable press enter to confirm
self-service
it's possible to enable or disable the
self-service option
press enter to open the submenu the up
down arrow keys serve to select
