WILL IT START? Caterpillar D4D Dozer

RetroCarz
284 followers
How about you?
I'm Hank, welcome to Hamiltonville Farm.
Today, we're gonna try to crank up that bulldozer.
Y'all stick around.
All right, we got a 1973 Cat D4D here,
but supposedly the engine runs.
So we actually wanna see
if we can actually get the engine running
because we wanna see if we can get it cranked up
and then maybe we can part the engine out
or sell the engine out of it,
or at least the motor might be worth something
if it cranks up.
We don't even know if it's gonna crank up yet or not.
Y'all stick around.
All right, so just like we got
with the Volvo Semi that we had,
got this Motley Crue with me here.
So, and again, I'm gonna try to do nothing
but a crescent wrench and maybe a hammer,
maybe a screwdriver,
but you guys with your $15,000 snap-on boxes,
you enjoy those.
Because I've got a $3 Walmart adjustable wrench in here.
So let's see if we can get this thing cranked up.
You know, we're gonna do our standard.
Let's check the fluids in it and all that stuff
because that's important.
Got our,
got our tool kit.
We got our wrench, our screwdriver, and our hammer.
So that would be enough tools to get this thing done.
Don't feel calm.
Hey, lose some weight, Tony.
Let's see if we got some oil in this thing.
Oh yeah, there's plenty of oil in it.
All right, cool.
It don't even look that bad.
Look at that.
So how long has this thing been,
how long has that thing been sitting here?
A long time, a few years?
Yeah, a long time.
Yeah, yeah.
So we'll put, replace the batteries in it,
check the fluids in it, and see if it's good to go.
You're stepping on the tool kit.
Yeah, I know it, right?
Well.
Oh, that's nice.
All right.
I don't see any water in it, though, do you?
We ain't gonna work that long.
Yeah.
Hey.
Hey, no.
What happened, Hank?
All right.
I'm gonna pull the filter out.
A little mask we got in there, Hank.
I know, and now I'm all scared.
I mean, I'm not scared.
I'm really not scared.
Oh, it's got a dry element in it, too.
Yeah, it's got the inner filter, too.
It will.
I just gotta...
Yeah, it'll come out.
There it goes.
Hey, listen.
We didn't even check the air filter in that semi, did we?
I looked in the hull.
Oh, you looked in the hull?
Yeah.
Hey, if you haven't seen that
Will It Start video with the Volvo Simo,
if you haven't seen the video with the Volvo Semi on it,
click this little banner right here
because that'll take you to that video.
Man, that's a really cool video.
You need to go check it out.
If you like these kind of videos,
make sure you hit that subscribe button.
Get through there.
Hey, we need to find one of them sticks.
That's just a little bit in it.
Here's your major stick.
Check around there.
You kept the special tool in the cab?
Oh, that's got plenty.
Oh, yeah.
Okay, let me tell you about the inside of this D4D here.
You got your master clutch here on this side.
This lever, you pull it back and it sticks.
And you got your steering brakes on your feet here
so you can turn left and right there.
And then your steering clutches are these two handles here.
That'll help you go left and right.
Got your forward and reverse lever here.
And then this lever here will operate
or actuate your plow.
Now, we use this for, or I say we,
they use this for plowing fire brakes
for control burns and stuff like that.
That's what this machine was used for.
So we're gonna take out this battery and this battery.
We're gonna put new batteries in it.
The fluids look good.
We've got the air cleaner out now
and we're gonna see if that will crank it up.
So let's see.
Mine run on these, don't it?
Them two clutches are pretty good.
Oh, there's another wasp.
I'm gonna have to try to hammer these off here.
I'm trying this out.
Special tool number two, hammer.
I'm getting you a good time, man.
One down, one to go.
Yeah, you're good now.
I hear my wasps.
It's like the dog said something.
Yeah.
Here we go.
You want them, brother?
That's our battery mounting block there.
One thing you want to make sure of
is that you don't start connecting batteries
before you're done putting the batteries in
because you may end up shorting something out
or shocking yourself or sparking or something.
So just be careful with that.
So when you're hooking up multiple batteries,
put the positive on both batteries first
and then the ground.
All right, so we're gonna crank this thing up,
but I don't want to take a bath
with all this exhaust stuff coming out here, right?
So I just hope I don't get sprayed here.
I'm gonna turn this master switch on down here.
It's kind of tough here.
There it goes.
Clicks.
Gonna hit this bad boy right here.
Here we go.
Gotta push this in
and let's see, make sure everything's in neutral.
It is.
All right, good.
Okay, so before we crank it up,
we gotta make sure that we got the glow plugs, right?
So you turn it to the left side here.
It's gonna put some glow plugs on it
and then we'll crank it up.
So I'll take this switch here
and I'll hold it over here
and I'm just gonna hold it for 10 seconds or so.
With that being said,
I get that the glow plugs are warmed up a little bit
because this thing's been sitting obviously
and we'll go from there.
So this is your throttle.
And so if you go all the way down,
that's wide open.
You got it up here.
So we'll set this throttle here a little bit
and see what that goes.
Yeah, it may have to heat again.
All right.
Hey, listen, I've got a lot of chiefs,
not a lot of Indians around here.
You know what I mean?
I probably can't say.
Is that politically correct?
Can I say that?
Not no more.
All right, we think we got some starting fluid
or as we like to call it around here, starting fluid.
So we're gonna go get some starting fluid,
just some ether,
spray it in there and see if we can get it.
I do hear water running when I turn it over.
I don't know if you can hear it on the camera or not
or on the video,
but I hear water running as I...
So I'm pretty sure that that thing's gonna give me a bath
if I ain't careful.
All right, ready, Brandon?
Yeah.
Little biceps.
Hey, Brandon, do that again I wanna show dude.
I wanna show him.
Watch this, when he primes that,
watch that fuel.
This is the fuel pressure gauge.
Watch that fuel pressure needle move.
So we got low fuel pressure for sure.
All right, let's try it again.
Turn the heat on it.
A couple of seconds here.
Maybe we get this one cranked.
Brandon, we're 750 in our will it start videos there.
So this might do us in though.
I know.
Thousand over here.
Five pounds.
Yeah, Tony's with us, he's batting a thousand.
All right, let's try that.
Ready?
Here we go.
Come on, baby.
Hang on.
So here's a disclaimer, right?
You really shouldn't be doing ether
in your starting fluid in your diesel engine.
All right?
Okay.
Come on, baby, come on, baby.
Oh man.
Great, it's a start.
Yeah, so basically we were running out of ether
cause it didn't have enough fuel in it
would be the assumption there, but.
Man, ain't that something?
Hold on a second, we're gonna keep trying.
Stand by.
You know that hurts my heart spraying the ether in there.
Is that right, Tony?
That's the worst thing in the world for me.
Yeah, yeah.
All right, let's climb out of this.
We didn't want to run it too long
because we know it ain't got water
or we don't know how much water it's got in it.
It didn't look like it had a lot in it.
So definitely don't run this thing long, okay?
We're all taking video of him getting out of this thing.
You gotta be like a monkey to get out of this thing.
Ow, it don't move, does it?
Tony told me, he said, no matter how hard I try,
I ain't gonna be able to move this thing with my nugget.
You know what I mean?
That's it.
So let me tell you exactly
why they're not running this dozer anymore, right?
This is what they call a track frame.
Some people call it roller frame, whatever.
So you got to take this off
so that you can access the back half of this machine.
This is your dead axle here.
All right, so once you got to put your frame,
your roller frame or your track frame
back onto this dead axle,
and this right here, this is your bull gear here.
And this bull gear has a sprocket on it, right?
And this sprocket is the actual piece that's broke.
You can see that it's broke here.
And the problem with this is
that it goes onto this sprocket here, like so,
like that right there.
And so there's an oil seal that is on this sprocket here.
And that's, you can't weld on this
because then you'll ruin that oil seal.
So we need this piece to make this tractor work again.
And then if we had that,
then you could put all the assembly back together
and this thing would actually run again.
But we can't find anywhere that makes this part.
So if you know of anybody that's got a D4D sprocket here
that's going to work on back of this,
leave a comment below or send me an email or something
because we might be interested
in getting this thing running again.
Hey man, this engine runs like a cat.
Purrs like a cat.
I got dad jokes, you know what I mean?
Hey, we got this thing running, purrs like a cat.
Man, this thing purrs like a cat, right?
So anyway, this is like take five of this outro.
So, you know, it wasn't funny the first time.
Put my heart into it, man.
I told him, I said, you guys gotta laugh at this thing,
man, it's our outro.
But anyway, but we really broke the toolkit out for this.
What did we use, five tools?
Five, yeah, we got really take a lot of this.
Yeah, we got a three tool limit,
but we actually had to exceed it on this one.
So we got two crescent wrenches, a screwdriver.
Hammer?
Yeah, and a hammer and a pair of vice grips.
So we actually exceeded the three tool limit
with the five tools that we had today.
So above Brando is a little white circle.
If you click on that, it'll take you to our subscribe page.
Underneath it is another video
that we have about will it start.
If you click on that, you can go watch it.
We've done a road grader, a backhoe and several more,
and a tractor, so several more.
So go watch those videos, they're pretty cool.
As always, we'll catch you on the next one.
You guys take care.
