A demonstration of how to build a simple wooden carry tray made from recycled timber. There is also a demonstration of how to make a dovetail joint.
HOW CAN YOU SUPPORT US? ▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀ This is how we make our living and it would be a pleasure if you support us! Get our Merchandise from https://bit.ly/3dFQxHV
g'day welcome to White cultivate today
we're going to be looking at making a
curry tray the sort of tray that is
suitable for collecting the veggies from
the garden and carrying them into the
kitchen ready for Preparation
in order to make this Curry Trail I'm
going to recycle a bit of Timber that I
have left over from a previous project
this is a bit of tongue and groove that
I previously used to make some shelving
and a desk so I'm going to make the most
of having these off cuts and turn them
into something useful
what I've done so far is I've taken each
of my Timber off cuts and I've first of
all ripped them down into the width that
I wanted and then the second thing I've
done is I've cut them into the lengths
that I want for my Curry tray you'll
notice that the ends are wider than the
the lengths the reason for this is
because I'm going to shape the ends of
these and I'm going to cut them in a
moment with a bandsaw in order to
provide a nice shape to the ends and
this is where we're going to form the
carry handles off my Carriage tray
so anyway we'll get on to that next
all right now I'll um finish this off a
little bit and give it a bit of a tidy
up with the sand
now that I've completed this end
I can use this as a template to Mark out
the other end of the carry tray and then
put it through the exact same process
all right so now I've got my uh two end
pieces and also my two side pieces what
I'm going to do now is to create the
outside frame of my carry tray and I'm
going to join the ends using dovetail
joints so the first thing that I now
need to do or the next thing that I now
need to do of course is to cut out the
uh the sections for the dovetail joints
I'm going to start first of all with the
dovetails which will be on the ends the
end pieces of my code
thank you
this is the Beast the dovetail will be
on
the depth of the dovetail needs to be
the width of the other piece of wood the
side piece of wood for my carry tray so
what I'm going to use or do is use this
piece of wood as a template for that
width
and I'll do the same on the other side
and there we have the width or the depth
that that actual dovetail is going to be
thing I need to do is to work out
exactly where the dovetails are going to
be on this bit of Timber I'm going to
have two on each end and the first thing
I'm going to do is to find the center of
this bit of Timber
so there's the center
and then of course each dovetail will be
equidistant either side of the center
foreign
now what I'm going to do is to use a
bevel in order to measure or to to Mark
the dovetail itself I like my dovetails
to be somewhere in the region of about
uh 20 degrees
or 70 degrees depending upon which way
you're looking at it
it's always a little bit difficult to
know which way these things go around
and so there I've got the dovetail
actually marked out on this bit of
Timber and I'll now do the same thing
foreign
over but I find as you will see the
ultimate result is very effective and
very tidy what I'm going to now do is to
cut out these dovetails that we've just
marked and I'm going to once again use
my bandsaw to do that It ultimately
produces a very tidy cut
thank you
foreign
so now I've got the dovetails cut on
each end of this uh of this coat tray
what I now need to do is to cut the
female section of the dovetail in the
side pieces and I'm going to actually
use the dovetails as the template for
measuring these out
process for doing this is as simple as
just clamping the side into a vise and
then
placing the side onto that
and using them as a template you'll
notice that I've actually marked the
side here with the letter a and at the
other end I've marked B and so on the
reason for that is because if I'm using
these for a template for this side
they'll be ever so slight differences
between each corner and so therefore
it's important that I am able to match
them up once I've cut them
and there we have it
the only other thing that I need to do
is to remember the depth and once again
I'm going to use this bit of timber here
in order to
uh act as a template for that depth
and there we have it
so I'll just make sure I Mark that a bit
more clearly
now I mark down
the sword let's
foreign
for the length
or the width I should say
there we have it
now I'm going to take this to the
bandsaw and once again
cut these out
the last stage of this is to take out
the angled section of this part of the
dovetop
like so
always remember you can always take a
little bit extra out but you can't put
it back so just keep that in mind and we
progress through and do this for
all of them
right so now we've got the dovetails cut
we've got them now in place the only
thing left to do now is to glue them
clamp them and to leave them for about
24 hours so I'm going to do that now and
then I'm going to call it a call it
quits for the night and come back
tomorrow and we'll put the bottom onto
the tray and of course we will cut the
handles out as well
see
okay well since last night what I've
done is simply glued clamped let it sit
for about 24 hours and now the glue is
dried I've taken the clamps off and you
can see that we now have a box without a
base of course but this will of course
become our carry tray
what I've also done is in the ends here
I've cut a couple of holes simply four
fingers in order to carry now I've used
a hole saw to cut these but you could
have just easily used a jigsaw or a
similar type of saw that you could use
for cutting such a hole it's quite
really up to you and up to you what type
of hole you would like to have there for
for carrying but anyway what we now need
to do is to move on to actually putting
the base on so we'll start that now
in order to add the base to this
character I'm going to add the center
Center section first the reason for that
is because this carry tray is in fact
only just a rough carry trades only
intended for garden use and so therefore
it won't be perfect with square by
adding the center piece first that
enables me to
then place the outer pieces
and
sand or plane them to length that way
providing a nice clean Edge on the
outside if I had in fact added the outer
pieces first it would have been a little
bit more awkward in order to achieve
that nice clean finish on the outside
given that the tray won't necessarily be
perfectly Square
so let's add this Center piece first now
in order to add this I'm going to Simply
glue and nail it so I'm going to add a
little bit of PVA glue to where that
Center piece is located
and then I'll simply
located in the middle
like so
and then nail
you can see I've now got two pieces on
and I'm just going to add the final
piece now
ensuring that I'm happy with the gap
between the pieces
my amp
and then nail it home
foreign
place
just need to wipe off some of the excess
PVA glue with a damp cloth remember PBA
is water soluble so therefore we can
wipe it off with a damp cloth that's
extremely important because if you don't
whatever finish that you choose to put
on to the final products can be affected
by any of that excess PVA so it's
important to remove it and as I said you
can do so with the damp cloth
yeah
okay
once you've done that it's now just a
matter of trimming up the edges just so
that we have a nice clean tidy finish
and uh and then applying whatever uh
finish that we choose to put onto this
tray
anyway
so here's the finished product
the only thing we now need to do is to
apply a final finish to this
in my particular case I'm going to give
you a good old-fashioned shellac but you
could choose to paint it or use a clear
lacquer it's really up to you it's up to
personal preference but I like good
old-fashioned shellac
if there are any comments that you have
that you would like to leave about this
video we'd really appreciate that you do
that through either the YouTube channel
or alternatively go to our website
icultivate.net
thanks for listening