Ellie's Handcrafted Jewelry 金屬纏繞 簡單的圓形珠子金屬纏繞吊墜製作教程

彩虹桥
165粉絲
4 次觀看·2026年11月16日
大家好,歡迎回到我的頻道
我是Aelizabeth,我家的手工飾品
今天我會分享如何製作這件可愛的小手巾
使用小大洋
它只需要幾個英尺的線
基本的飾品工具都可以用到每天
但我們先開始
請按讚,別忘了
訂閱並響起通知鈴鐺,纔不會錯過新片
讓我們開始吧
材料和工具
你要用一根操縫杆
三塊6英尺長的線
28英尺小的線
12 mm round cabochon, chain nose pliers, round nose pliers, and flush cutters
Now to get started, I've already marked the center of my wire, which is a 3 inch mark
And I'm just going to start by making sure that my wires are parallel to one another
And then I'll grab my weaving wire, and then I'll go ahead and start weaving together my three base wires
I'm going to begin by wrapping the weaving wire around the bottom base wire three times
I'm going to bring it up and around the bottom two base wires one time
Make sure that they sit nicely together
And then I'm going to bring that wire in between those two bottom base wires
And then around the top two base wires one time
And then in between those two to wrap it around the top base wire one time
And this is called the modified sumac weave, and this is what we're going to use to secure all the wires together
Now bringing it from behind, I'm going to wrap it one time around the bottom base wire
I'm going to bring it up and wrap it around the bottom two base wires again
In between those two wires, and up and around the top two base wires
Then in between, and then around the top again
And we're going to do this a total of three more times to make five rotations around the base wires
Once we've woven those together, I'm just going to compress the weave slightly with my chain nose pliers
And then I'm going to wrap the weaving wire around the bottom base wire three more times to secure the weave
And then I'll trim off the excess by doing a little twist method
You can also use your flush cutters for this
I'm going to begin weaving around the middle base wire here
So I'm going to take my weaving wire and bring it down
And then I'm going to go ahead and start the coiling by wrapping it around
And we're just going to do this for about half an inch to three quarters of an inch
Now once I've coiled both sides a total of three and a quarter inches
I'm going to go ahead and bring this down, and I'm going to begin using the stone to kind of help me create the frame
So holding it against the surface, whatever surface, and then using your fingers to gently wrap it around to create the frame
And this will be very fiddly, so just take your time with it
You can also use a dowel that's about the same diameter if that's easier for you
And this is where the stone should sit
And from there I'm going to go ahead and take my pliers and bend the wires straight up
And they should all be parallel to one another
And it's going to be bent up right where the coil ends
And now I'm just going to stick my stone in there and just make sure that it's still fitting properly
And now I'm going to grab my weaving wire again, and I'm going to wrap it around that base wire on the right side
And I'm going to wrap it around three times to start
Now I'm going to begin wrapping the weaving wire around all of the wires, just making sure that they kind of sit nicely together
We don't want them to cross too much
So I'm going to wrap it around in total three times to bind these wires together
Just make sure they sit nicely together
This will be a little bit more difficult with round wire than square, but you can do a fairly decent job if you just hold it carefully with your fingers
Now to secure the weave, I'm going to go ahead and bring it around the front
And wrap it around this top base wire here
And then basically begin another modified sumac weave, but using the front two wires
And so we're going to wrap it around this first to start the weave
Making sure that they are sitting nicely together
They should be parallel
Wrapping around both wires
Between and around the top wire
Then around the bottom base wire one time
And then wrap it around both base wires
Bring it around the top base wire one time
And then around the bottom base wire one time
And we're just going to go ahead and continue this weave until we reach about three quarters of an inch to an inch
And then we will create our veil
So I've woven a little over an inch
I'm going to go ahead and complete my sumac weave by wrapping it around the bottom base wire three times
And then a little pull and twist
Pull that off
And that completes our weave
Now I'm going to pull the wires apart
I'm actually going to pull three wires to my right
One to the left
And then I'm going to bend the veil portion over the back
So over the top of those wires
I'm going to direct those remaining base wires there from the weave
I'm going to direct them through the frame
And use those pieces to secure it to the frame
So I'm pulling the front a little bit like so
And then bringing the back
And then I'm going to trim off the excess wire
And then I'm going to make sure that they're nice and snug against the frame with my chain nose pliers
With that I'm going to go ahead and carefully bend the front of the frame
I'm going to mix a little bit with my pliers
But I'm going to use my finger to kind of hold that there a little bit
And then create a little prong
So that way we can stick our stone in there
I'm going to use my chain nose pliers to kind of angle that a little bit more
So that way there's plenty of surface area
Do the same on the opposite side
And once I've finished fiddling with it
I'm going to go ahead and grab the stone and stick it in there
Carefully
Making sure that it doesn't pop out through the front
Making sure that there's enough surface area there
And as you can see I'm kind of moving the prongs forward a little bit
Since this has a rounded top on it
So it's nice and neat
Sorry I am a perfectionist so I have to do that
So now that it's sitting where it belongs
I'm going to go ahead and glue the back
And you can have a little bit more glue back there
So that way there's plenty of backing for the stone to sit in
And I'm just going to repeat that on the opposite side
This is where the pendant should be at this point
And now I'm going to grab the bottom base wire here on the right
I'm using my thumb to make a swirl curve
And then using my index finger to kind of help guide it
I'm going to go ahead and wrap this around
Put it back
I'm going to bring this to the frame
And secure it to the frame
Once we've secured that wire
The middle base wire goes next
But before we do that
I'm going to go ahead and grab the leading wire
And create another coil similar to the frame there
And this is a little bit of an easier way to do it
I'll just wrap it around the top
And coil it around the top a little bit faster this way
And then once you've coiled all the ways
You can actually just slide the coil down to the bottom of the base wire
At this point I'm going to go ahead and slide the coil down to the bottom of the base wire here
And at this point you can also do a control and twist method
To take out that excess wire before you move on
Or use your flush cutters
And once I get the coil where I want it
I'm going to go ahead and carefully begin
Following the first base wire with my curling wire
As you can see I have a little bit more ways to go
So I'm going to go ahead and just continue coiling
Until I get to that ground
And I'm just going to go ahead and continue following that wire
And bring it over to the side
Like so
And then I'm going to bring that back also
But before I do that
I'm going to add a little bit of coiling
Let that burn
And then once I kind of get as much on there as I need
I'm going to go ahead and twist it off
Now I'm going to trim the wire just a little bit
And then I'm going to bring the rest of it to the frame
Using my chain nose pliers
And once I've secured that second base wire to the frame
I'm going to go ahead and follow that same base wire
With my third base wire
And I'm going to secure it to the frame
The same way I did the previous wire
I'm going to take this one remaining wire
And we're just going to curve it a little bit
So it's going to be a little above center
From the rest of the wires
And bring it around
And secure it just like we did with the previous props
Just making some final adjustments
And here's your finished pendant
I hope that you all enjoyed this tutorial
If you have any questions or just want to share your work
You're welcome to join our Facebook group
There's a lot of fun going on over there
Lots of sharing and encouraging one another
Also you can check out my Etsy site
Currently all my written tutorials are over there
So all the links are in the description below
If you want to check those out
But before you go
Hit the like button if you enjoyed the tutorial
And don't forget to subscribe if you enjoy these videos
And until we meet next time
Have a great day
