¿ARRANCARÁ Caterpillar D4D Dozer?

RetroCarz
284 followers
Loosen that up.
How about you?
I'm Hank.
Welcome to Hamiltonville.
Today we're going to try to start that bulldozer.
Stick around.
Alright, so we've got a 73CAD D4D here, but the engine supposedly runs,
so we really want to see if we can get the engine to start,
because we want to see if we can start it and then maybe we can sell the engine
or at least the engine might be worth something if it starts.
We don't even know if it's going to start or not.
Stick around.
Alright.
Just like with the Volvo Semi that we had, I've got this motley crew here.
And again I'm going to try to just use an adjustable wrench and maybe a hammer.
It might be a screwdriver, but you know, you guys with your expensive toolboxes enjoy,
because I've got a $3 adjustable wrench from Walmart here, so see.
Let's see if we can get this thing started.
You know, we're gonna do our standard,
we're gonna check the fluids and all that stuff because it's important,
but we have our, we have our toolkit, it's got a wrench, screwdriver and hammer,
so that should be enough for this.
Don't feel like, wait.
You lost some weight, Tony.
Let's see if we have any oil in this.
Oh, yeah, there's quite a bit in it, it doesn't even look that bad.
Look at that.
So how long has this been here?
How long has that been here?
A long time.
Years, yeah, a long time.
Yeah, yeah.
Come on, let's replace the batteries, check the fluids, and see if it's good to go.
Screwdriver.
Use it as a stepping stone in the kit.
Yeah, I know, sure.
Let's see.
Oh, that's nice.
All right, I don't see any water in it.
You're not gonna run it that long.
Loosen that.
All right, just take the filter out.
The old belt got in there.
I know, I'm all scared now.
I'm not scared.
I'm.
Not scared.
Oh, it's got a dry element.
It will.
I just got a yeah, it'll come out.
30, there it goes.
Make it run better there.
Hey, listen.
We didn't even check the air filter on that semi, did we?
You looked in the hole.
Hey, if you haven't seen that video of will it start with the Volvo Simo.
Simo, if you haven't seen the video with the Volvo Semi,
click on this little banner here because it'll take you to that video.
Man, that's a really cool video.
You need to go check it out.
If you like these videos, hit subscribe.
Hey, we need to find one.
That has something in it.
Here's your manual.
Stick around.
You used to have a fuel dipstick.
Did you keep the special tool in the cab?
No.
Oh, it has a plan.
Oh, yeah.
OK, let me tell you about the inside of this D4D.
Here you have your master clutch.
Here's this lever you pull back and it stays.
And you have your steering brakes on your feet here to turn left and right.
And then your steering clutches.
These are these two handles here that help you go left and right.
You got your forward and reverse lever here.
And then this lever will operate your plow when we now use this for
or I mean we used it to plow fire brakes for prescribed burns and things like that.
That's what this machine was used for.
So we're going to take this battery out and this battery,
we're going to put in new batteries.
Fluids look good.
We'll take the wiper out and let's see if that starts it.
So let's see.
It takes skill to operate these because those clutches are.
Oh, there's another wasp.
All right.
I'm going to have to I'm going to have to try to hammer these in here and test this.
Special tool number two.
Hammer.
I'm having a good time at the price.
All right.
One down, one up.
It's like the dog.
It was the beans.
Yeah.
And here we go.
That's our battery pack.
One thing you want to make sure of is that you don't start connecting batteries before
you finish putting the batteries in because you could end up shorting something out
or electrocuting yourself or sparking or something.
So just be careful with that.
So when you connect multiple batteries, put the positive on both first and then the negative.
All right.
So we're going to start this up, but I don't want to take a bath with all this
exhaust coming out of here, right?
So I just hope I don't get wet here.
I'm going to flip this switch right here.
It's a little bit hard here.
There it goes.
I'm going to push this bad boy right here.
Here it goes.
Come on.
I got to push this and make sure everything's in neutral.
That's great.
Before we start this up, we got to make sure we have the glow plugs, right?
So you turn it all the way to the left side.
This is going to put some glow plugs in and then we're going to start this up.
So I'm going to take this switch right here and I'm going to hold it right here and I'm
just going to hold it for about 10 seconds or so.
With that being said, I understand that the glow plugs are a little bit warm because this
right here has been sitting there, obviously.
And that's where we're going to go from there.
So this is your throttle.
If you turn it all the way down, it's open.
You have it up here.
So we're going to, we're going to adjust this throttle a little bit.
See where that's going.
Yeah, I might have to try that again.
There you go.
Hey, listen, I got lots and lots of bosses.
No, no, lots of Indians over here.
You know what I mean?
I probably can't say it.
It's politically correct.
I can say that.
I didn't just put it in there anymore.
All right.
We think we got some starting fluid or as we like to call it starting fluid.
So let's go get some ether, spray it on and see if we can do that.
I hear water running when I turn that.
I don't know if you can hear it on it.
I don't know if you can hear it on camera or not, but I hear water running as I'm sure
that's going to give me a bath if I'm not careful.
There you go.
It's not even acting like it wants to start.
Really hard to get in.
Oh, yeah, there.
It's doing something.
Warming up again.
Almost there.
Starting to move.
Oh, man.
Well, let's try some more things.
That idea.
Yeah, coming up.
It's gonna be.
Yeah, we found the primer here.
Let's do it.
Okay, let me see it.
Hey, brand, I'll do it again.
I want to show.
I want to show you.
Look at this when I get it.
Look at that fuel.
This is the fuel pressure gauge.
Look at that needle.
We have low fuel pressure.
All right, let's try that again.
Turn the heat up in a couple seconds.
It might start brand.
We're at 750 on our video of it starting.
So this could this could take us out.
I know, though.
Dot 1000 over here.
Yeah, Tony's with us.
He's hitting a 1000.
All right, let's try that.
Okay, here we go.
Ah, come on, baby.
Hold on.
So here it is.
Here's a disclaimer.
You shouldn't use ether in your starting fluid in your diesel engine.
So I'm using those engines to get.
Come on, baby.
Oh, man.
Hey, are we?
Yeah.
So basically, we ran out of ether because it didn't have enough fuel in it.
That would be the assumption.
But man, it's not something.
Wait, we're still trying.
Stay tuned.
Give me a little more.
You know, that hurts my heart.
Spraying ether in there.
That's true, Tony.
That's the worst thing in the world for you.
Yeah, yeah.
I think it's fine.
All right, let's go.
Let's get out of this.
We didn't want to keep it running too long.
We know it doesn't have any water or we don't know how much water it has.
It didn't look like it had much.
So don't keep it running too long.
We're all taking video of it getting out of this.
Dot, you got to be like a monkey.
Oh, it's not moving, is it?
Tony told me.
He said no matter how hard I try, I'm not going to be able to move this with my head.
You know what I mean?
That's it.
So let me tell you exactly why they're not using this bulldozer anymore.
This is a track frame.
Some people call it a roller frame or whatever.
So you have to remove this to get to the back half of this machine.
This is your dead axle right here, OK?
So once you have to put your frame, your roller frame or your track frame back on this dead
axle and this here, this is your main gear and it has a pinion, right?
And this pinion is that's the piece that's broken.
You can see it's broken right here.
And the problem with this is it goes on this pinion right here.
So as you know, right there and there's an oil seal law that's on this pinion and you
can't weld that on this because you'd ruin that oil seal.
So we need this piece to make the tractor work again.
And if we had that, you could put the whole thing back together and actually would work.
But we can't find anyone to make this part.
If you know anyone who has a 4D pinion that works on the back of this, leave a comment
or send me an email because we might be interested in getting it working again.
Hey, this motor runs like a cat.
It purrs like a cat, huh?
I got dad jokes, you know.
Hey, we got this thing working.
It purrs like a cat.
Man, this purrs like a cat, right?
So.
Anyways, this is like the fifth attempt to a zipper.
So, you know, it wasn't funny the first time.
My heart, man.
Yeah, I told them you gotta laugh at this.
Man, this is our zipper.
But anyways, we really pulled out the tool kit for this.
We used five tools.
We have a three tool limit, but we exceeded it.
So we have two adjustable wrenches, a screwdriver, hammer, and a hammer and locking pliers.
We exceeded the three tool limit with the five that we had today.
So above Brandel is a little white circle.
If you click on that, it will take you to our subscription page.
There's another video below that about whether it will start.
If you click on it, you can watch it.
We've done a motor grader, a backhoe, and several more tractors.
So several more.
Okay, so go check out those videos.
They're great as always.
I'll see you in the next one.
Take care.
