How to replace the cabin filter in a Nissan E-NV200 electric van. A simple DIY job.

E-Moving
15 followers
1 Video ViewยทMar 10, 2025
Hi it's Matt here from Go Green Autos. So in this video I'm going to show you how you change the
cabin filter in a right-hand drive Nissan ENVY 200 or indeed the ENVY 200. So on right-hand drive
vehicles everything is done on the passenger side because the cabin filter is behind the glove box
here inside the dash and all you're going to need for this job is basically a Phillips screwdriver.
So what you've got to do is remove three screws two are there you can remove the glove box just
by pushing the sides in and that will fall out but it doesn't have to come out and then the other
screw is in the cup holder there and you can help it a little bit by removing the door rubber here
but pulling this out is going to pull that out anyway so yeah you could help that just by
removing that and then you're going to get hold of this plastic trim and pull it this way towards
your passenger seat. It doesn't look like this one's been removed so I'm going to need two hands
to get on there and pull that but yeah just snaps that way. So this just comes out straight like that
not ideal doing it in this weather because it is very cold and plastic tends to get quite brittle
when it's cold so you can break clips but anyway you've got three clips along the top
some on the side here let's just shed some light onto it there and yeah just clips in along the top
along the side and then you've got these plastic lugs which just locate in those holes at the
bottom and then once that's out you can get to the cabin filter which is up here above the fan
and there is just a vertical panel on the cabin filter housing and you just squeeze
either side squeeze those two towards each other to release the clips either side like that
and then you can get the tray out which holds the cabin filter and that's there. So looking at this
one it is quite dirty and this is a genuine Nissin one and it has an arrow there saying up
however I have a feeling the aftermarket ones generally have the arrow in the airflow direction
which will actually be down but anyway this one is a carbon filter so they are grey anyway
whereas most of the aftermarket ones aren't carbon but that doesn't make an awful lot of
difference it's far better you change it more frequently so yes I've got a blueprint one here
and you'll see here the arrows show airflow so I need to have a look up here I've got a feeling
the airflow is going to be down so yes your air is coming in from the top below the windscreen
so yes in this case we're going to be mounting that that way because the airflow is down through
it which obviously is the same because yeah we can see the dirty side was at the top so dirty air in
at the top and filtered clean air out the bottom so we want to fit that one the other way around
arrows going down which I wouldn't be surprised actually if these were printed wrong on the
original ones but I'm sure it doesn't make an awful lot of difference but anyway stick your
cabin filter in there just make sure it's sitting in that tray properly there is a tiny little
tags which sort of just grip the edges and then put that back in reverse so before you put this
back in position one thing you need to do is remove this end panel first and that's just a
simple case of getting your fingers in there and just removing it by pushing these clips down
you need to remove that because these clips stick out and catch here and if you see your van has got
a bold in this panel it's because someone has banged this back in without removing this first
so remove this panel first push the whole trim back and then snap in that panel afterwards
and then put your rubber seal back and that's how you do it if you've got a passenger airbag
you'll actually have a switch on here and that switch protrudes inside quite a bit I haven't
done one with an airbag for a long time you don't get many passenger airbags on these vans
but when you've got that you actually need to remove that panel first before you take this
off because that switch is going to stop this coming forward but you want to loosen this
first because trying to get a tool in here and getting that panel off ruins that panel and you'll
see a lot of them are like that they're all twisted because people have tried to remove that first
so what you need to do if you've got the airbag switch there is pull this out to loosen it
and then you can get your fingers in here and release some clips and then pop this panel out
before you then fully remove that as I said it's been a while since I've done one with an airbag
but I'm pretty sure that was the correct way of doing it because trying to pop this out while
it's in situ without getting a finger behind to loosen the clip does tend to sort of ruin this
panel but not many with airbags but yeah it's all very simple to do so that's it I think so
if you found this video useful please do click that thumbs up button on YouTube because that
really does help other people find the channel plenty of EV videos on the channel as well so
do look at those and do subscribe if you haven't and I'll see you on the next one.
One final thing to add is you often get spilt liquid around the cup holder here so before
you snap that glove box back in place it's worth giving this a clean particularly along this seam
and it's probably worth snapping out the cup holder itself and then putting this under the
tap to clean the inside and also you often get coffee stains and things down this side panel here
so when that's off again stick that under the tap and give it a good clean.
So I'm just putting this back together and I've just noticed actually the two clips are broken
on this end piece of trim and that's I assume from previous services probably at Nissan dealers
and that's exactly why you need to remove this before you snap the glove box back because those
two clips get in the way and they've obviously banged this and have broken those off so simply
by removing this before you put the glove box back stops this and makes it an awful lot easier
it just goes back flat and then you put this in afterwards and then you find this
stays nice and flush and doesn't bulge out like you see so many of them doing.
