Beautiful 3D Flower Resin Trinket Bowls

Plastic Craft
37 followers
#resinflowers #resinart #resin
Making a custom order of 3D flower resin trinket bowls. If you enjoyed this video, leave a like and subscribe for more :)
Hi everyone, I'm Nadia and in today's video I'm making 3D flower resin trinket bowls.
The first thing I'm doing is mixing my part A and my part B resin together for a few minutes
until there's no more streaks and my resin is clear. I already have my molds out and the pigments
that I'm going to be using and then I separate my resin into smaller cups to add in those pigments.
You can use a medium or a high viscosity resin. Then I poured clear resin into the molds.
I do my best of making sure that there's an even amount of resin in each mold
and I use a wooden stick to help push the resin to the edges of the molds.
This was a custom order set of two white and purple trinket bowls as well as two white and
gold trinket bowls. So I start off by mixing my white pigmented resin and I'm using Depon's
Ocean Wave pigment paste. I make sure to mix the pigment in the container first before I add a
small amount into my cup of resin. You can use my code SUMMERGIRL to save 10% off of Depon's website,
I'll leave a link below. Next, I'm using just resin's pigment paste in the shade bright gold.
I also have a discount code SUMMERGIRL to their website and I'll leave everything in the description
as well as product links that you see in this video. Next, I'm using Vitrol's transparent pigment
in the shade red violet. I use a torch gun to pop any air bubbles and make sure you're moving your
torch gun very quickly so that you don't burn your resin or your silicone molds. And I start
off with the red violet pigmented resin and I pour it into the shape of flower petals.
And I do the same with the gold pigmented resin. Then I pour my white pigmented resin.
I use a small wooden stick to drag through the resin from the edge into the center in
between each flower petal and do a little swirl motion in the center.
And I just take some gold leaf flakes with my same wooden stick and add it into the center.
And here I am demolding the next day. Both sides came out really nice and usually I would use the
bottom side, but for this custom order the top side looked more like what the customer had wanted
so I decided to use that side. I demolded them a bit late so they weren't very bendy and they
difficult to shape into a bowl. Depending on the type of resin you're using and its pot life,
you can demold anywhere from 8 hours and you should be able to shape it into a bowl.
However, a quick tip if you've demolded too late like I have is that you can heat up your piece
with a heat gun which will cause the resin to soften and it'll be a lot easier to shape into
a bowl. I believe I had demolded this the next day so definitely over 12 hours has passed if
not even 24. After I've softened each one, I place them into a small bowl. Another tip that I would
suggest is to place something between your bowl and your resin piece so that the resin doesn't
get stuck onto the bowl. I believe plastic wrap is the easiest to use but you can also try to use
baking paper. You'll see later in the video since I forgot to do that for these, some of my pieces got
stuck onto the bowl and I had a hard time removing them. I placed something on top of each piece and
applied tape around the whole bowl to ensure that it stays in place. However, if you demold your
piece earlier then it's a lot more flexible. You probably won't even need to put anything on top.
I allowed them to sit like that for a few days and here I am removing the tape. As I mentioned
previously, because I didn't put anything between the resin piece and the bowl, some of my pieces
got stuck and what I did in this case was I soaked it in warm water for around 10 minutes
and then I was able to remove it a lot easier. Lastly, I add a gold trim with a gold adding marker
and here's the final product. Thank you guys so much for watching. If you liked this video,
subscribe to see more videos like this in the future.
Follow me on my Instagram, summergirldesigns, and my mom's Instagram, wildheartresinart.
