Evolution of the Oil Industry | Documentary on the History of American Oil and Petroleum Industry

Professional Development
12 followers
5 Video Views·Feb 28, 2025
This 1950 film is a documentary on the history of the oil industry. It shows the oil exploration activities, the drilling for oil, the refining processes and uses of the final products. The film includes general scenes of American life in the 1940's and 50's.
Evolution of the Oil Industry | Documentary on the History of American Oil and Petroleum Industry
Comments are disabled for this video.
From the dawn of history, mankind has revealed an unconquerable urge to improve his lot.
Along with his requirements of food and shelter have been the deep-rooted desires to reduce drudgery
and to move freely beyond the horizons of his limited domain.
Time and space have always presented their challenge.
Man early recognized that energy must be found, harnessed, and properly applied to help him.
But throughout many centuries, man was unprepared to see the potential servant
in a substance that occasionally seeps from the earth's crust, oil.
Oil has long been known to mankind. Aware of its unusual burning characteristics,
the Babylonians dipped their ceremonial torches in oil and pitch.
In drilling wells for water and brine, the Chinese came upon oil 600 years ago.
Their energy and power facilities remained, however, limited and primitive.
Little did they know that oil such as they encountered
would someday be a source of freedom from toil and drudgery.
Early American Indians used the oil that they found as a medicine and ointment.
And even in the 1800s, petroleum, recovered as a nuisance by-product of brine well drilling,
was sold as a cure-all. But now the progress of civilization had set the stage for an awakened
interest in petroleum. Animal fats and tallow could no longer supply the ever-growing need
for candles and lubricants. Oil oil, which had long been the chief illuminant,
was becoming scarce, yet the demand for artificial light was increasing.
In 1850, a lamp capable of efficiently burning a refined product of petroleum was invented.
Petroleum, it seemed, might supply the growing need for lubricants and light,
but digging for it, it seeps, could not supply it in sufficient quantities.
The fact that some oil had been found while drilling brine wells
suggested the interesting possibility of drilling for oil itself.
In 1859, a derrick was constructed near oil seeps at Titusville, Pennsylvania.
This was accomplished under the direction of a retired railroad conductor, Edwin L. Drake.
With the assistance of an experienced brine well driller, Uncle Billy Smith,
operations finally got underway. Crude handmade tools and the primitive steam engine
enabled them to drill at a rate of only three feet per day.
A depth of 69 and a half feet had been attained with no encouraging signs
when one Sunday morning, Uncle Billy took a look around.
Thus, on that eventful day of August 27th, 1859, Edwin Drake and his associates ushered
in a new era. It had now been shown that oil in substantial quantities could be obtained by
drilling. With the rapid spread of the news came a fantastic migration of those who saw
in this development a possible source of new wealth. The boom was on. Towns and derricks
sprang up almost overnight in the vicinity of Drake's discovery. For lack of engines and
drilling equipment, many crude but ingenious drilling methods were devised. Strong backs
and legs and infinite patience supplied the power to drill only a few feet per day.
With the realization that many drillings resulted in expensive and disappointing dry holes,
so-called experts with divining rods, luck, and intuition were much in demand.
Yet the combined efforts of these pioneers resulted in rapidly increasing oil production.
Waiting for slow and inadequate transportation, oil piled up at the well sites. Storage became
a vital problem. Anything that could hold oil was pressed into service. Thousands of wagons
and teams became regularly engaged in hauling the oil to the nearest shipping points.
When possible, barges and rafts were employed to carry the oil.
Such transportation proved inadequate in supplying the fast-growing market.
And so in 1865, the first oil pipeline was laid over a five-mile distance from
Pithole City to the railroad. Within nine years, a 60-mile trunk line of four-inch pipe
stretched from the oil region to Pittsburgh. Seeing the rapid loss of their revenue to
the successful pipelines, the Teamsters fought hard and bitterly. But they could not stop the
growing momentum of the industry's progress. Crude refining plants, or stills, boiled and
separated the oil into the two items in demand, kerosene for illumination and heavy lubricants.
An undesired product, considered dangerous and unusable, was discarded in great quantities.
The product was gasoline, the very portion of crude oil that was soon to change the economic
and social status of the industry and the country. These refineries were, however,
supplying illumination and heat for many homes, and through lubricants, were freeing the wheels
of a fast-growing industrial machine age. At the turn of the century, a momentous change
in the course of the industry was in the offing. The use of oil for light seemed doomed to rapid
oblivion. At this critical stage appeared the invention that was to revolutionize the oil
industry's course of progress and change the living habits of the nation. No longer was gasoline
destined to be a useless by-product. Instead, with the swift popularity of the automobile,
gasoline quickly assumed the position of prime demand.
With the development of the internal combustion engine, a long unrecognized potential use of oil
had at last been revealed to mankind. The recognition of oil as an economical and easily
handled liquid source of power was the springboard for a new era of magnificent progress. Inspired by
the American system of possible reward for risk, discovery and expansion swept westward to the
Pacific, the Mid-Continent, the Gulf Coast, and the Rocky Mountains. The oil industry quickly
found its stride in the suddenly stepped-up tempo of progress. Increasing and improving oil products
had kept pace with invention and even forced it to proceed at a rapid rate.
Through enterprise and the accumulation of knowledge, it has now reached a stage of maturity
undreamed of even a generation ago. Throughout millions of years since the Earth's formation,
constant heaving, buckling, and erosion have changed many portions of the Earth's surface.
Many areas were repeatedly covered by shallow seas. Countless billions of tiny organisms died
and settled to the bottom, where they became buried under sand and silt. There, it is believed,
the entombed organisms were transformed into oil. Accumulated pressures of gases,
water, and earth sometimes drove the oil through the porous sand and sedimentary rock,
and often it migrated to underground reservoirs sealed by non-porous formations where the oil
was trapped. It is from these reservoirs that oil is now most likely to be recovered in commercial
quantities. Thus today, the oil geologist searches both for locations where oil may have been formed
and locations where oil may have been trapped. Conditions that were favorable to the formation
of oil may be indicated by traces of ancient seas and fossilized remains of long-extinct
organic material. Underground formations where oil may have been trapped may be indicated by
surface structures. Stereoscopic photographs are a great aid in the study of surface indications.
Another method of search for oil is through chemical analysis of soil samples for minute
evidence of seepage of the lightest hydrocarbons. The economy of this method permits blanketing
large areas, and promising indications are then verified by more expensive detailed geophysical
methods. In the far-flung search for oil, modern geologists and geophysicists often make use of
the helicopter and the marsh buggy, a special vehicle which can take them into almost inaccessible
swampland. Subterranean oil traps may be found by mapping underground formations. The gravity meter
gives clues to the nature and depth of these formations by measuring the gravitational pull.
The magnetometer is another instrument that can help plot underground formations by measurement
of the Earth's magnetic fields. One of the most important of all methods of search is the
seismograph. A shallow hole is drilled for a small explosive charge, and special microphones are
strategically placed around the shock. The detectors will pick up the explosion and the
shock waves reflected from far underground. This will give information as to the shape and depth
of the underground strata. The shock waves are reflected by the various rock layers underground
and are recorded at the surface. The time it takes for the waves to make this round-trip
varies with the distance they travel. The recorded measurement of this time lapse
indicates the depth. Thus, through a series of shots, the shape and depth of underground formations
are mapped with accuracy. The seismograph is even used to detect potential drilling sites several
miles out at sea. Special sensitive geophones are lowered into the water to predetermine depths
and positions. Explosives are detonated under the water. As on the land, the recordings of
reflected shock waves reveal variations in the ground strata under the seabed.
Actual drilling is still the only conclusive step in finding oil.
Even today, in new field drilling, only about one well in nine becomes a producer.
Costs of drilling a well will average about $77,000, but some wells have cost as much as a million.
The older cable tool method is still generally used in drilling formations hard enough to stand
up well and where low costs rather than speed is the principal consideration. The rotary drilling
method, developed since the turn of the century, is now used more extensively. Although more
expensive, it is speedier and enables drilling through loose, unconsolidated formations to far
greater depths. In drilling to depths of two or even three miles, the repeated raising,
lowering, and handling of the drill pipe to replace the bits is a difficult, time-consuming function.
Steel pipe, or casing, is used to line the well walls and give them strength
to prevent caving in of the hole. Cement pumped around successive strings of casing
seals the holes against leakage of oil, gas, or water. As the drill passes through various types
of formations, weight on the drill bit must be suitably adjusted. This retards wandering of the
accumulating weight of added drill pipe. Senses of taste and smell are used as an occasional quick
test when it is suspected that oil-bearing formations are being approached. Core samples
are taken with a special drill bit at some drilling locations. These are sent to field
and central laboratories, which test them for porosity, or the volume of small cavities that
may contain oil, permeability, or the potential rate of flow through the rock pores, and the oil
content of the sample. Still another method of estimating underground conditions is through
measurement of electrical resistances at various drilling depths. This process is known as electric
logging. During the process of drilling, a special valve at the top of the hole may be closed off
in the event of unexpected blowouts. When an oil-bearing formation is reached, the drill is
pulled. Heavy muds are used to hold back the flow of oil from natural pressures.
Wells are no longer permitted to blow in as dangerous wasteful gushers. A final string of
casing is set. Some wells are shot with explosives, permitting the oil to flow into the well.
When the glass-enclosed charges of this perforator are detonated in the hole,
powerful jet explosions penetrate the casing and surrounding rock.
A small diameter tubing through which the oil will come to the surface is installed.
At the surface, a system of valves called a Christmas tree is installed. This controls the
flow of oil. Sometimes wells are treated with chemicals or acidized to open up passages in
limestone for the oil to flow through. Other chemicals may be used to stimulate oil flow and
prevent water migration to the well. When natural bottom hole pressures are not enough to force the
oil to the surface, the well is put on the pump. In many locations, ingenious centralized power
systems work a number of well pumps, bringing the oil to the surface and sending it to the
In the present-day application of scientific production methods,
the industry is wisely trying to conserve reservoir energy by maintaining subsurface
pressures. No longer are wells drilled without regard for adequate spacing.
The production of individual wells is carefully regulated to prevent
waste or depletion of reservoir energy. However, in many fields, reservoir pressures have been
lowered to a point where oil does not flow naturally to the wells. In many such locations,
natural gas, usually associated with oil production, is first piped to cycling plants
where liquid products are extracted. Oil production on land has been augmented in recent years through
drilling at sea. Oil producers are thus opening vast new production potentials to bring more oil
to the nation. Today's oil scientists know that crude oil is a complex chemical mixture of
molecules of many different kinds. It is a liquid treasure chest from which hundreds of finished
products may be derived through refining. The industry's complex research is constantly
disposing new products from oil, as well as developing processing techniques designed to
In the initial stages of modern refining, the flowing oil is heated in a pipe still to about
800 degrees Fahrenheit. This superheated oil then enters a fractionating tower.
Upon release from the confinement of the pipes, all but the heaviest portions of the hot oil
flash into vapors and start to rise in the tower. Various components of the crude oil vapors
condense or change back to their liquid state at different temperatures. As the vapors rise to
successively cooler levels, the heavier fractions condense on lower trays and the lighter components
collect on the higher trays. Thus, products or fractions ranging from asphalt and heavy oils
on up to light oils, kerosene and gasoline, may be drawn off independently. While fractionating
or distillation is a process of separating oil components, cracking is a term applied to the
process of breaking big molecules of oil into smaller ones to make more of some fractions
than would be obtained by ordinary distillation. Through cracking, twice as much gasoline can now
be produced from a barrel of oil than with distillation alone. While this may be done
through heat and pressure alone, a more modern and efficient method is with the use of a catalyst.
Oil vapors are passed to a reactor together with the catalyst.
This is a substance that has the ability to change the molecular or chemical structure.
The mixture of cracked vapors is then sent to a fractionating tower for distillation or
separation of the newly formed components. The used catalyst is sent to a regenerator that prepares
it for reuse in the system. A number of other ingenious processes are now employed to take apart,
put together, or rearrange the molecules of petroleum.
Through a carefully controlled production balance of refinery products, the oil industry now supplies
not only fuels and lubricants, but the basic ingredients for a limitless variety of chemicals.
These in themselves are the foundation of gigantic new industries. Petroleum-derived plastics,
found in many of our modern fabrics, are made in plants such as this.
The manufacture of soaps and detergents is another large enterprise using petroleum products.
The synthetic rubber industry is still another based upon petroleum-derived chemicals.
Recent times have seen a tremendous increase in the uses of a variety of synthetic rubber.
Today the distribution of petroleum and its byproducts has in itself become a tremendous
enterprise. A network of pipelines is an essential part of this undertaking.
Modern machines have greatly eased and speeded the task of digging the trenches
and preparing the thousands of miles of pipe required.
Pipes were formerly screwed together, but modern welding techniques help produce a
continuous and unbroken artery of steel. Before they are buried, the pipes are thoroughly cleaned.
They are next covered with a special compound that resists the corrosive action of the chemicals in
soil. Further protection is given by a smooth spiral wrapping. Thus the life and serviceability
of the lines are prolonged. Nearly 140,000 miles of pipe now carry crude oil to United States
refineries. Another 23,000 miles of pipe carry finished products of petroleum. A gigantic system
of pumping stations forces petroleum and its products over and through all kinds of terrain.
Under modern methods, various oil products are pumped through the same line in adjacent
sections or units. Modern oil tankers and barges account for a large percentage of the bulk
transportation of oil and oil products. The tankers are indispensable for the overseas movement of oil.
Railroad tank cars have also kept pace with oil development, many of them having
specially prepared compartments. They daily carry millions of gallons of various oil products.
More than 100,000 tank trucks are in service today. They represent an efficient and flexible
means of oil distribution. Through such trucks, there is an ever-increasing trend toward distribution
of oil products direct from the refinery to the service station and the consumer.
The automobile service station itself represents a high degree of friendly competitive efficiency
in modern petroleum distribution. Through petroleum, Americans now travel with efficient
economical power while the complex machinery that carries them is protected and lubricated with oil.
Beauty and efficiency surround them in the synthetic leathers and fabrics made from petroleum
and in the plastics from the same source. Oil-derived synthetic rubber cushions their
ride and seals out noise and weather. The safe, long-lasting tires on which they ride
may be made from oil. Eighty-five percent of the roads on which they travel are paved with
petroleum products. Through petroleum energy, people and products are now transported speedily
and economically throughout the nation and the world. Man's desire for freedom of movement has
been fulfilled with petroleum. What three gallons of gasoline did 25 years ago, two gallons will do
today. Machines powered by oil now enable the farmer to produce three times as much as he could
before oil became his faithful ally. Oil keeps the farmer's home as well as his brooders.
It protects his fruit trees from killing frosts and oil products are used to spray his trees.
No longer a slave to the soil, the farmer has been freed to enjoy a fuller life
and an ever-improving standard of living.
Through oil, our nation's defenses are maintained with a speedy mobile army
as well as a fast, hard-hitting air force. Our flexible, long-range navy and merchant marine
now move with oil. It has been estimated that the energy available from our current output
of petroleum would be equivalent to the labor of about 10 times as many people as there are
in the world. The modern 30 billion dollar oil industry is a large factor in the support of
national economy through wide-scale direct and indirect employment.
And through a limitless variety of products and uses, it is contributing to nearly every
phase of American living. In the relatively few years since the oil industry's inception,
traditions of progressive service and responsibility have been established,
which will be the foundation for even greater contributions to the welfare of the nation
and the world. Man may now look with grateful pride at his short but spectacular history
of development and use of petroleum. Through truly American enterprise and ever-increasing
knowledge, our lives will be yet further enriched through the wise and efficient
utilization of this bountiful resource, oil.
