How I Used Hot Glue To Fix This Dent | Paintless Dent Removal

Autos hacks
81 followers
15 Video Views·Feb 10, 2025
Today I'm going to walk you through step by step my process in how I removed this dent damage
from the rear wing of this Audi. As you can see it's a fairly good sized dent but what adds to
the complexity of this repair, the panel itself is convexed. That means it curves out around that
wheel arch. The dent itself has a crease running right through the middle and if that wasn't
enough it's also taken in that body line. So here from the rear lamp right down towards the wheel
arch is the manufacturer's body line and as you can see my crease dent runs right through the
middle. So there is a lot going on with this damage but I'm going to take you through with
me step by step go through the tools, the techniques and methods I used to repair this
damage. Now if you haven't done so already don't forget to subscribe to my channel.
So the first thing I want to do with damage like this is check for the access points.
I plan on glue pulling most of the damage out but it's always good to know where your access
points are from a finishing point of view. See if I can get different tools, rods and bars behind
to allow me just to get a really nice clean finish. I intend to do most of the repair with
glue pulling sort of techniques and then perhaps if it needs finishing take out some of the damage
with some tools from the inside. So I'm checking for access points I can get in here and get to
this whole back section through this access point here. What I'm currently thinking of doing
is taking out this little piece of the crease that I can only as far as the main body of the dent
and then probably do the same with the fine little creases
on the other side. So I'll take out that damage on that side,
take out the damage on this side and that should leave me with just that dent.
And I'm going to glue pull that dent trying to get that body line back out again.
I've taken the screws out of the undershield.
I can't get the to show up on the camera but there's a hole about there up on the inside of
the arch. So with that access point, this access point I know I can reach the majority of the dent
and I intend to glue pull all of this. So I'm going to start this repair from the back end.
I've got a hockey stick style tool with a blade tip going right through that access point to get
me on the back end of this crease. I'm going to take out the crease damage to the left and right
of the main bulk of the dent and that's going to make sure all of the tension is where I want it
right in the middle ready to rework that body line. You can see the lines pinching together
as my tool tip connects right into the center and as I speed up this repair process you can see the
way that metal moves and comes back into the correct shape. So now that I've tidied up that
tail of the crease on the rear I'm going to go through the other access point under the wheel
arch and do the same thing for the front end of that crease. So at this stage I'm looking to take
out the left damage and the right damage to about 90% really to give me a true shape to the panel
make sure I've released any crowns any tensions leading right into the middle of the main bulk of
the dent and then I've just got one big dent to work with. So again as I speed up this process
you can really see the way that I move around the way the metal responds and just gentle precise
pushes right along that crease line to take out the majority of the damage either side of the
main bulk of the dent. I'm just repairing this little crease here from this angle you can see
I've got a crown so I quite often call this hidden damage and that's where the damage has
traveled across got to a point it won't go any further so it sort of pits a bump
crest into the panel at the very edge of the repair. It can be quite easy to miss
but that certainly needs to be all tapped down have that little bit of tension that
little bit of crown released allowing that metal to flow each way. But before I tackle that crown
I'm just going to take out the high spots that I created during that last pushing process with
my tool tip from the inside. I'm using a root beer tap down which is great for giving me some precision
it's also a lighter weight and so is the paddler I'm using to tap it down with. It's got a leather
pad on the inside so it gives me a really nice soft damper and now as we assess this crown you
can see where those lines pinch together and it curves and runs down vertically so I'm going to
gently tap down that high that crown and I'm going to use my blending hammer for this. Now I'm not
blending I'm just using my hammer in a similar fashion to when we're using that tap down and a
hammer but it's just a bit quicker for me using the blending hammer and the tips as opposed to
holding a tap down and a hammer in two separate hands. Okay so I've taken out the damage that was
taken out the damage that was here so now I'm going to be focusing on the main dent
so obviously we've got this crease that runs right through the dent
it's fairly deep but it is fairly soft I think
so I don't consider this a crown and that's just the top of the dent
it'll start to release as I bring this dent outwards
there may be a tiny bit of tension on the body line of the arch
but not anything to worry about at this stage. Now what I'd like to do is put tabs either side
of the crease and then gradually bring it up so that I should finish pretty much on that body line
so a tab here tab here and lift it up and I'll be directing my pulls that way
and that way to pull out the metal this way and this way
I'm hoping that's going to come out as a fairly clean
dent or start to pop out as I'm releasing the tension but there is a crease running
through it so even when the big dents out there'll probably still be a fine line that needs to be
worked now you've got a very slight crown here a more pronounced one on the back end here
so I'm going to do a couple of light little taps here
and here and that reduces some of the tension which will help me be able to pull some of the
low but by putting pressure and tapping this way I'm encouraging that tension in the panel
to move that way and as I'm tapping this side of the crown again kind of directing it this way
by applying pressure here and here I'm going to be sort of persuading that metal to come inwards
which is going to help in that lifting process so I'm starting on the outer edge of the crown
and tapping it inwards and that's what I mean by helping feed the tension this way so my crown's
there and I'll start tapping it tap tap tap tap tap in towards the end so now that I've released
the tension from the outer sides of that dent we can focus on the glue pull section as always I'm
going to make sure my panel is warm clean and well prepped and then we'll start the hot glue
process so I've put a bead of hot glue right along the center of this crease tab now the tabs I'm
starting with are from Black Plague PDR this is the gangrene smooth series I've got a small crease
tab on the left and a slightly longer crease tab on the right allow that to cure just for a few
seconds before setting up my slide hammer now watch the direction of my pulls I'm directing
the slide hammer to the left and that is allowing some force on the tab itself to help me direct
that pulling force in towards the center of the dent and then the same on this side pulling and
directing the slide hammer in the direction I want that pull so already you can see it's massively
reduced the outer size of that dent and bored it in now a lot of people think with a slide hammer
you're just pulling it straight out but you can definitely direct the force of that energy in
that pull and help persuade that metal to go in the direction that you want to feed it and it's
all about that metal flow and this is one of the many things we teach over at learnpdronline.com
my dedicated training platform for teaching paintless dent removal so that first pull
pulled out some of this dent and it's just started to move so bringing it slightly shorter
this line here was where my other tab was so you can see I've reduced the dent of that first pull
I've still got that crease running through it which I'll either glue pull or see if I can get a tool to
but as I've taken that crown pushed it this way released some of this crown pushing it this way
the original crease I was working with the bars and rods is here
my first glue pull was this section here and you can see it's almost taken the tension with it
to give what looks like another crown on the back end so this time I won't be really tapping that
crown I'm going to continue my pull along this crease line same again one that side one this side
bring it in towards the crease
so setting up once again for the next stage of glue pulling
it's a similar process I'm aligning these tabs and once again watch the direction of my slide hammer
gradually bringing it around to the right and that is encouraging the left hand side of that tab
to lift and that's lifting towards the center of the dents and then repeating on the left hand side
so now after our first stage of glue pulling let's have a quick assessment of the panel and
see how we're getting on you can see I've massively reduced the overall size of the damage
reducing the crease from the left and right hand side bringing it all in towards that center point
across the body line as my damage has got smaller and the crease is more defined I'm now switching
to the Kiko Robo lifter with their dead center tabs now the combination between this lifter and
those tabs is killer when it comes to these fine creases you get such precision and control
in being able to lift out just that fine line that center line of the crease
I'm just gradually working the metal gradually squeezing that lifter
and allowing the tab and the glue to do its job of pulling up the metal
and just as I did before I'm looking to address the left hand and right hand side
either side of the main body line now it's a slow process just gently working the metal in
towards the middle and throughout the repair you really have to look at the panel as a whole
make sure that you're working within the shape of the panel and not getting lost in any of the
tension or missing any points sometimes you can be so zoned in to the center point below that you
are working it's easy to forget to look around the entire panel and just make sure everything's
going in the right direction where you want that metal to move so switch back to a gangrene tab
these are slightly wider and I've got it going right through 45 degree angle of my body line
because that's the line of the crease so I'm just trying to get the center point of that body line
lifted back up again and it did start to move so already we can see the line is starting to take
shape a few more glue pulls and some fine tap down work and it's really starting to shape up well
so the main large soft dent is now being removed just in the process of restoring this body line
you can see we've got a little bit of distortion here
and where the main crease was we still have some signs of the crease itself
so you can continue to kind of glue pull this with the crease tabs and lifter
or see what areas you can get to through this access point or this access point to finish it off
you can see I've got part of that crease running through here
now that I've got the majority of the shape back into the panel
I'm going back to my bars and rods I just find I get really good precision
accuracy work in the low spots so the glue has helped me reduce the overall size relatively
quickly and now what I consider the fine tuning leading towards those finishing stages I can get
my tool straight behind the dents read the damage across my line board so right now I can still see
signs of that initial crease gradually pushing along those lows from the inside with my tool tip
bringing it up until my reflected lines read true now during that process you do create some small
high spots with your tool so I regularly switch and take those out with my tap down hammer process
but also as the dent starts to unfold and the panel starts to take its shape
again have a look across the entire panel in that nice natural light look at all the reflections
around you and make sure the whole panel looks consistent it's important on every dent but even
more so with large damage as I said before you can be really zoned in and focused on one particular
spot and sometimes forget to assess the panel as a whole so now I've cleaned up this whole
back section from here to here through this access point a little bit of tap down work
drawing the metal that was in the outside in towards the middle and then with the tip of the
tool working my way along the low spots from the original crease of the dent and also working my
way along this body line making sure I've got a nice straight line so with this longer bar
I can get through that hole all the way along to the other side of my crease
so I've nearly taken out the whole dents come into like the finishing stages and we can just
hopefully pick it up on the line board so running right through the middle here there's a slight
high like a crown so the lines are slightly wider here slightly wider here and then more tight
between this little gap here so again the sort of thing that can be very easily missed
but without identifying that crown tapping it in you might not necessarily get to the low
damage across this line here once again I'm choosing to use my blending hammer this is
the shane jacks blending hammer and I've just got a dent craft mushroom tip on the end
and I'm using that to gently tap down my crown my high spot you can do this with a hammer and
knock down but with a bit of precision and accuracy I just find it quicker doing it with my hammer
and again another quick assessment across the panel just making sure it's all looking good
and we've not missed any of the damage so now with my line board set up hopefully you can see
what I'm looking at from my angle some of those lines slightly pinched together some of them are
slightly wider apart so this is kind of like ripples across the panel and I'm using my blending
hammer to smooth this out so the areas that are very slightly high are now being tapped down and
that metal that's high is being dispersed back into the low and those lows are naturally being
lifted up just by that high metal being placed down and smoothing out that panel so I'm blending
across my repair area but I'm also going to blend out the damage from my repair area out into the
rest of the panel and this just gives me a really nice consistent finish from the repair across the
entire panel itself so I'm blending out my damage area but I'm also blending it in to the existing
texture of the panel so as I run across with my line board again we can see it's looking pretty
good it's pretty clean there's a couple of minor little details that I'm going to continue blending
out and a couple of micro lows that I'm just going to touch the back of with my tool tip just to make
sure I've got a really nice clean repair so if you're interested in painting this dent removal
and you're wondering how you can get started in the industry learn more about the tools the
techniques and methods we use to fix dent damage check out learnpdronline.com you've got all of
the information there right now to get you started today training and pdr now I'm here to help you
every step of the way so reach out to me ask me any questions and as always I hope you've enjoyed
this video if you have don't forget to give us a thumbs up to like the video and of course you can
subscribe to the channel please do leave me your comments and feedback below this video here on
youtube I do try and come back to every comment I get so I really hope you've enjoyed this video
and I'll see you in the next one
