Carving A Chess Board - Step By Step Beginner Wood Carving Guide

Carving Art Channel
11 followers
12 Video ViewsยทFeb 8, 2025
Hey everybody, this is Brian from Carvingisfun.
In this video I'm going to share with you how I made my chess board to finish up my
chess set whittling project that I made here.
The whole project was fun and pretty easy to do.
It was a little bit time consuming but you know what?
I had a great time making it.
Now to make the chess board you're going to want a piece of wood that's going to be big
enough so that you can divide it by 8 going across and it's still going to have enough
space so that each square is going to be a little bit bigger than your actual chess
piece.
Since my chess pieces are about 1 inch in diameter I opted to use a 12 inch by 12 inch
slab of wood here.
It was not really easy to do in a wood shop so I had to buy a full on 4 foot by 12 inch
piece of wood and just cut it to size.
So you might need a wood saw if you can't find a 12 by 12.
And then after that you're going to need some tools to carve and shape with.
So you can use a chip carving knife if you want to but I primarily used a V gouge and
a couple chisels to round and make little gouges in the wood.
And after that you're going to want whatever paint or stain that you can use to show the
different color squares.
Then you're going to want a pencil and some sort of a straight edge to create straight
and even lines with and a tape measure to make sure you're spacing everything out equally.
So first things first you're going to want to make sure you get the wood cut to size.
Doing so I made sure I measured the width of it before I actually cut the length off.
That way I'm making a perfect square because sometimes when you get a 12 inch wide piece
of wood it's going to be just a little bit skinnier than that so you're going to want
to make sure you're cutting it to about the same exact length as the width so you don't
have to do any fancy measurements for the width of each of the squares.
After you cut the board to the right length and width that you want go ahead and hit it
with some sandpaper.
I used some 220 grit sandpaper and sanded along with the grain to remove any of the
tooling marks from when the board was made.
So what I did from there is I went and took one of my chisels and I beveled off all the
sides right here.
I did this first because I knew when I beveled the edges I'm actually going to reduce the
overall width on the top of the board which I'm going to be using a measure with which
ended up being about an inch and three eighths wide per square.
So after that I used my straight edge and my pencil and made lines all the way across
and then I started adding my stain.
Now this part I should have done something a little bit different where I just made the
gouges or cuts like a light gouge or cut going all the way across on the lines first before
applying the stain.
I think that might work better so if I do it again next time I do that.
This is primarily because it would help prevent some overflow from some of the paint because
I did have some issues where I thought I could keep it within the lines and well that just
didn't happen.
So you got to account for that.
Now like I said you can also use a V gouge or a chip carving knife.
Both will work just fine.
The V gouge is a little bit faster as you can make a straight line very fast but you
can also do it with your chip carving knife.
So you just have to make sure you're doing it right here and follow the line.
This might take some practice for you.
Make sure you're getting all the way across and then flip it around and just try and meet
that line up.
If you do it right it should pop right off.
Now don't worry about the lines being perfectly straight.
Even with the V gouge for me it wasn't perfectly straight in some cases because I got a little
carried away or the green kind of directed me to a different angle.
So either one will work.
The V gouge is much much faster so if you had the option to use that I would highly
recommend using the V gouge.
Then after that like I said deepen some of the cuts and then do some cleanup work.
You might have to remove some bleed over like I had to do or I accidentally dabbed some
of the stain in another square.
Then after you get done making all your gouge marks and touching up everything removing
most of your blemishes with the chisel you're going to probably want to go ahead and use
some sandpaper to remove off any of your excess stain or paint that might have touched elsewhere.
Then apply a finishing coat to the whole thing including the darker spots that you did.
I used some beeswax paste.
It was super fast, super easy.
Just apply it and buff it off.
Let it sit for a little bit to dry up and it creates a nice little protective layer.
Now if you wanted to further protect it you can put a little bit of felt on the bottom
of your chess pieces and it will help add a little soft barrier on your chess board
so you don't scratch it up while you're using it.
Now if you want to see how I made all the other chess pieces go ahead and check out
my chess making series.
I'll show you everything from making the pawns to the kings and queens.
Thanks for watching everybody.
I hope you have yourself a great day.
