The Spear: Forging the Most Used Medieval Weapon in History

Forging the Past
1 follower
4 Video Views·Feb 5, 2025
The spear has been one of the most basic yet most effective weapons in the entire world for most of History!
Not an easy task to take on, using only medieval tools, but we were down to try it! If you'd like to learn how to make one yourself, this video should prove very helpful. If you're only interested as a viewer, this video should prove worthwhile in that regard too!
Hold there for a moment.
Is this a robbery?
Of course this is a robbery. I have a knife.
That's not a knife.
That's a knife.
Ah, but who said anything about knives?
A sword, eh?
That's not a sword.
That's a sword.
You think that's impressive?
You and your big sword.
Well, hello, hello, and welcome back to Black Hammer Arts.
For really the first actual craftsmanship forging video we've done since the Viking Axe.
Just because of all the drama lately.
But today we're going to be forging a spear.
And I would say, I would contend that the spear is probably the most used weapon in history.
It's also the, or nearly the oldest weapon, other than maybe the knife, in history.
And the reason is, even though swords are super iconic and used in melee.
And I love swords and I want to make one.
Spears, they give you this reach.
But they're also, they're so much more simple to use than a sword.
And simpler to make, too.
So, that's what we're going to be making today.
It's going to be a Celtic war spear style, loosely.
So on this channel we use medieval tools and traditional craftsmanship methods to make everything we make.
But this should, regardless of your setup, be a pretty step-by-step guide to making your own first spear.
If you'd like to.
And honestly, you don't need that many tools.
And you don't need to be that skillful.
It's not that hard.
Before I mention anything else, I'm going to show you this is what we're making it out of.
This is a piece of a truck spring, actually.
Spring steel.
I mean, just basic stuff.
You can find this in scrap yards everywhere.
Or in my case, my backyard.
You can see I've cut it off at an angle here.
Just to make it easier to form a point.
And I'll show you how I do that.
But you could also start with it flat on the end, like this side is.
And make a point after.
That's fine.
One other thing I'd like to mention before we hop into it.
It's just one of the most amazing things about how crazily our channel has grown in the recent past.
It's just all of the amazing comments.
We've gotten literally thousands of comments at this point from a ton of different people.
And almost all of them have been extremely positive and helpful and kind.
And some of my early medieval history and craftsmanship heroes have actually come and commented.
That's just been super, super cool.
So like Shadiversity is one of the people who absolutely inspired me to even start something like this.
I mean, yeah.
Absolutely one of those heroes.
And then Niels Ogren is an amazing axe maker.
If you want to see some real axe making, go over to his channel.
I'll leave a link down there.
He is just an amazing, phenomenal axe maker.
And I've been watching him for a long time.
So that's just been super cool to see.
And then one final thing.
I'm going to also make a mention at the end and we'll have credits because you guys are awesome.
But the Patreoners.
We have gotten an insane response to the Patreon.
But yeah, it's been amazing.
Without them, I don't think we would be able to do this.
They actually paid for the stuff that I'm going to be using here in the video.
So yeah, let's get into the project.
Alright, so here I'm going to be creating the waist of the spear.
Which is exactly what it sounds like.
Not like a waist product, but like a waist, you know, on a person.
And yes, I am using an anvil fuller.
I mean an anvil.
A hardy horn as a fullering tool.
Why? Because I'm doing medieval blacksmithing.
So I can't create a modern one.
It's actually working pretty well though.
This is the first time I've tried this on this particular tool.
I should get some better tongs on this though.
So this is obviously going to be the separation between the blade and the socket.
Now I've pretty well marked it.
I'm definitely not going to lose that.
So just a little tip here.
Really make sure you are on a diagonal coming off this corner.
About this angle.
Otherwise it will bounce all around the place.
Like this, you see it doing bad things.
So you want to make sure your hammer is coming in right at that nice angle.
So you can see, I've got the waist pretty good and thinned down.
I'm not sure if it's quite the final dimension yet, but it's pretty close.
So the next thing I'm going to do here is blend this a little bit.
This is a little bit hotter than it looks.
The sun is shining on it, but I am getting to the end of my heat here.
Then we'll have the fun part.
I'll be spreading it out this way with the cross beam, which you'll see.
So here, I'm going to be spreading it like this using the cross beam.
It's pretty self-evident what's going on.
I'm going to be starting at the end here.
I'm eventually going to work all the way up to here.
But that will take quite a few heats.
Be careful when you get it this thin.
It's easy to burn.
When I get real thin here, I'm switching to the rounded side of the hammer.
I just find it's easier not to damage things and easier to make them even that way.
So you can see here, kind of proportion.
This is the original width down here.
This is how wide it is now.
So it's starting to get fanned out to close to the right amount.
I'm going to start moving on and focusing more up here, especially on this side.
I'm trying to make sure it looks even.
Currently, it's a little bit more fanned out on this side.
A little more on this side, and then we'll get to wrapping this thing.
Interesting. Very interesting.
I did not actually encounter this last time.
The kind of diagonal swoop that this one has.
I'm guessing they must not have been quite equal.
In how they were spread.
But I think I can fix it, so I think it'll be okay.
I've devised a scheme to try and straighten this.
This line is a little bit angled.
Because they're not, you can see, they're not wrapped quite evenly.
So what I'm going to do, I'm going to heat it up.
I'm going to grab this in here.
And I'm going to twist it.
Around.
And I'll twist this around and hopefully straighten it out.
Let's see if it works.
Alright, so it's day two.
And today we're going to be making the socket a little bit cleaner.
And then punching the hole and finishing the blade.
Just kind of being gentle here.
Rolling this together.
So this, whether you realize it or not, is actually one of the trickiest parts.
For me at least.
Of making a spear.
And I have definitely not mastered the science of doing this part.
We've got the socket closed up here on the end.
So the next step is going to be to correct the point to the center.
And then start forging out the blade.
Probably do one more heat striking on this area before I take over the beveling.
So historically, obviously, power hammers, water powered trip hammers did exist.
I would like to build one one day. We'll see if I ever get around to that.
But historically a much more common way of moving large amounts of metal was like this.
You'd have a two man striker team.
Or sometimes you could even have, I've seen up to a five man striker team before.
It's very impressive. It takes a lot of coordination.
But the basic mechanics of how it works is I am in this case the master smith.
So I strike. So say I strike here.
And I let up and Justin will strike in the exact same place.
Wherever I strike, he will strike.
That will all work up and down.
Him just following me. And when I tap on the anvil, that means stop.
It's gotten thin enough to where it wants to bend over now. Not a big deal though.
Just getting this thing nice and ready before I go into the beveling process, which will be next.
There is actually a little bit of a skill to keeping it going without really stopping in between.
But I find if you kind of roll them, like you go out a little bit, kind of like.
But it's easier to do from that position obviously.
That's a little better.
What's it looking like? Nearly good.
I could get used to this.
Yeah, just keep an eye on it.
Yeah, here let me take a look actually.
Yeah, it's good. Good to go.
Is it going boy? Is it going boy?
Yes!
I'd say it's not quite up yet.
Oh yeah, that side is. Good enough.
Maybe a little low, but.
So everybody leave some love for Eddie down in the comments.
Every comment equals one pet for Eddie.
That's right, he already gets free pets.
Normal part of making a knife and also a spear or any sort of blade really,
you have to take a file and true up your edge so it looks like you want,
unless you are a perfect blacksmith.
So that's what I'm doing now.
The way this is going to work, and you can probably see this,
is it's going to come over and it's going to hit all the high spots
and then it's going to miss all the low spots because obviously it's going to skate.
So it's a pretty good way to make sure your edge is even.
This is biting pretty aggressively.
Alright, so it's the start of day three.
Today we have to punch the holes.
Now typically, modernly you would drill the holes because punching
into this kind of a scenario is very tricky,
but I'll show you how we're going to do that later.
And then I just want to see if I can slightly straighten the neck of this here spear.
And that'll really be pretty much it for the forging part of the spear.
We're nearly done.
So this kind of strange little tool, which you've been seeing throughout the video,
is a hardy horn, and you can see what it is pretty easily.
It's just kind of a round piece of steel that is square on this end.
It goes down into the hardy hole and then obviously it's bent over and rounded.
But the interesting thing comes in, because you've probably seen these,
or at least you can if you haven't, all over YouTube and on the internet and stuff.
A lot of smiths use them.
But the interesting part comes in with this little hole here.
And right here, there's a hole punched through this,
which is approximately the same size or just,
I mean it's almost exactly the same size or just barely larger than this punch here.
It's a little bit dovetailed at the top, the hole itself.
And so the idea is, I'm going to stick the socket of the spear on this,
then put this punch on the socket over this hole,
and punch it into the hardy horn.
So yeah, it's kind of a unique idea I've never seen anywhere else.
This is where kind of the historical archaeology aspect of our work here comes in,
because obviously every single blacksmith makes all sorts of weird individual tools.
I've done it, everyone does it.
And this idea was actually not mine, this idea was actually Justin's, interestingly enough.
I was in the office talking to him about how I couldn't figure out
how to put this hole in it without squashing the socket of the spear.
Because obviously in modern times you just drill it,
but medieval times, how do you do that without flattening out your socket?
He had the idea of drilling or punching a hole through this,
which I did, and it worked.
This is actually one operation I do recommend you wear a glove for.
I forgot to put one on.
There you go.
That worked much more like it was supposed to.
And that's a beautiful hole, actually.
Really nice.
Go ahead and take a look at that.
So just sticking the file through here to clean up any little burrs.
But yeah, you can see when I stick this file through,
it's pretty nice and centered.
It's pretty well in the middle of the socket, so that's good.
Yeah, pretty good.
What you just saw was me putting on the touch mark.
I have a little stamp.
I placed it on there and hit it and stamped my maker's mark into it.
So yeah, the next steps are going to be normalizing.
And while that's going on, I'll be making the handle.
While I'm heating this up, I'm going to heat this up,
make sure the entire blade is real good and evenly heated.
And then I'm going to bury it in the coals,
and I'm going to leave it for the entire night.
That's going to anneal it,
which will basically not only make it very soft and easy to file,
but also will make sure that all the stresses that have been created
by hammering it will all disappear when I anneal it.
So that's what I'm doing right now.
And while that's annealing, I'm going to be working on the handle.
You're going to want to make it out of some kind of hardwood.
There's a lot of different options you could choose from.
I've seen people use birch, which is kind of softer,
but it's still an option, apparently.
I've never used it.
This is ash. I find this to be a really good option.
You can do a lot of things.
Generally, for a spear, you're going to want it to be
around as tall as you are, or taller.
In this case, taller, because in my opinion, longer is better.
But it's up to you.
And I'm going to make it slightly oval.
You could also make it perfectly round,
and I think that's what most people do,
but I don't like perfectly round handles, generally.
I find that when I hold a weapon in my hands,
it's slightly disorienting if the whole thing is exactly the same,
because I can't really feel where I'm at.
I have to look and see where I'm at.
But you can do whatever you want.
This is going to be pretty simple.
I'm going to be using a draw knife.
I'm going to be locking it in the vise,
and just doing exactly what you would think I'd be doing.
I'm going to skip most of this,
for the sake of the video, but you see what I mean.
One point, you're going to want to figure out
which way it wants to work.
If it's wanting to pull you down into the grain, like this,
you're going to create notches like that.
So then you're going to want to work the other way, like this.
And you can see I'm going to get this out no problem.
But, yeah.
Next up is going to be quenching the blade.
You see this in all the Hollywood movies,
when they either quench it in water a lot of times,
which is actually a big mistake,
or quench it in oil, which is obviously what we're doing today.
But before I quench it, I've got to preheat the oil.
So that's what I'm doing right now.
It is advisable to wear a glove while you do this,
because of that fire.
The reason why it's important to do this,
is to make sure your oil is good and thinned down,
so it appropriately hardens the metal,
when you actually go to quench the real thing.
It's important to keep this moving when you do this,
because otherwise it can form a steam jacket around it,
and not allow it to properly quench.
So it skates a file, for sure.
It's definitely hard.
Also, be very careful at this point,
because it can very, very easily crack and break.
It's super brittle.
So I'm just kind of...
It skates a file, so it's past that test.
I'm trying to just kind of scratch off
a little bit of the scale on here,
with the file,
to try and see if I can see any temper colors,
when I go to temper it in just a second.
Sticking it on top of the forge,
to try and get some of the heat,
from the forge,
to temper the blade.
You know it's tempering when you get to
a kind of deep straw color,
or light blue,
kind of a purple.
I'm looking for kind of a straw to light purple.
Basically makes the blade not quite so brittle,
because when you quench it, it gets very brittle.
Now at this point,
the only part that might have been mildly hot,
was the socket.
The blade was pretty well cooled down,
but yeah,
it's down to a good temperature now.
So this is now hardened and tempered,
provided I didn't miss anything.
So I've got the spear all nice and brushed up,
and it's looking great.
So now we're going to start fitting it
to the handle here.
Marking which side it's going to go where.
All right, so something I forgot to mention.
You may have noticed the shaft
looks like nice and stained and stuff.
Now, I did that off camera,
and I may have to do a little bit of restaining
here on the end,
but yeah, I'm pretty happy with it.
Important thing to note if you do this,
which by the way,
this is working amazingly.
I stopped trying to stick the head on,
and I started sticking the handle in,
and this is working amazingly well.
But important thing to note,
don't hit it too hard,
because this actually is,
you'll be surprised,
this is incredibly effective.
It really squashes up in there,
and it's solid.
So next thing we're going to be doing
is sticking the pin through right over here.
All right, so you're going to need
a little drill bit or auger
to make that hole, obviously,
in the same place as the metal ones are.
Going through the handle there,
and then you're going to need a little rod
the same size as that hole.
And you can see this one's a scale,
so I'm just going to lift it up
and let it cool.
You don't necessarily have to do this,
but the reason why I did
is to hopefully make it softer
and easier to rip it over.
So I guess we'll see now how it works.
So you'll want to make sure
that it's roughly even on both sides,
about the same amount
sticking out either side.
our spear making video.
I had a great time making this project.
It's not the first spear,
and I really hope that it inspired you
to make something.
Maybe not a spear, but maybe.
Whatever it is, I hope it inspires you
to be useful with your life
and make things.
I also want to say a special thank you
to our patrons.
We got an amazing response
when we mentioned it in our last video.
And if you would like to help support the channel
so we can keep on making videos like this,
more of them, go over there.
And if you've got any questions
about the process or anything
just hit the thumbs up button
and the subscribe button.
It does help us get out there,
so if you do that, I'd appreciate it.
And until next time, farewell.
Warbufare.
