Timber Framed Barn Part 4 Milling 20 Tons Of Logs In To 8x8's

Nature house
148 followers
#NaturalHouse, #EcoHome, #SustainableLiving, #GreenArchitecture, #EcoFriendlyHome, #OrganicLiving, #NaturalLiving, #EarthFriendly, #EcoDesign, #HealthyHome, #GreenLiving, #SustainableHome, #NatureInspired, #EcoHouse, #EnvironmentallyFriendly
So it's time to start doing some milling.
Finally got some dry weather, it's been a long time coming.
The ground is still quite wet but I'm going to push on as best I can.
I've made some modifications to the mill, just added a measuring stick
and moved over the stops a bit and reset it up nice and straight
so hopefully we get some nice good cuts.
Got new blades and we'll try and knock out a few 200x200 timbers, 8x8s.
Right, so the first one's on, let's get to work.
We'll let that warm up a bit and then we'll make the first cut.
Right, I have to say that is cutting really nice, well happy with that.
It's just too much waste for my liking so the next one I'd do,
well the next one I'd do is that which is wind braces because it's massive
but the next one I'd do, I'd try and get two or three cladding boards out of it first.
But yeah, nice.
Oh Jesus, that is heavy.
Come on.
So this next log is just absolutely monstrous.
So what I'm going to do, it's too big for me to really roll up on the mill.
It's half a tonne on its own, it's massive.
It's five metres long and really wide.
So I think I'm going to make this into wind braces because I need nice wide bits
because I can cut a curve in them and I'll try and cut the pith out.
But I can't get them out of these basically so I'm going to make this big one into wind braces.
Right, got another one up on the mill, another section of that log I've cut up.
Three sections and they're all going to be wind braces.
I've taken the first one down the bottom.
Just push on, it's getting late in the day but it's still nice out so I'm going to make the most of it.
Right, I've had a pretty nice day actually.
Really enjoyed myself to be honest with you.
Things went well, mill's working good.
Nice new blade, new belts.
Yeah, all went to plan.
Lovely out in the sun.
Really enjoyed myself.
It's quite hard work this time of year, sometimes with the wet weather and stuff.
But yeah, had a nice time today.
So I've just cleared up the last of those three sections of that big log.
Slabbed up, brace material.
I'm going to stack that down the bottom.
And then tomorrow I'm going to do the same with that big one over by the digger.
And then I'll be into, it looks like, doing 8x8s or 8x10s.
So yeah, carry on tomorrow.
Right, morning everyone.
Another nice, cold, dry day.
Bit frosty out.
But yeah, nice. I'm looking forward to a nice bit of milling.
Feel good being able to get some milling done.
Been a bit stressed about how much I've got to get done before the end of March.
And getting milling done makes me feel better about it.
Nice, dry. Ground's hard.
Yeah, really good.
I'll show you what we got milled yesterday.
Got it stacked up down here, the slabs.
Ready for brace material.
So yeah, there's the brace material we got milled up yesterday.
I'll get it covered up before we get some rain.
But I'm going to get this stack filled up today.
Because we've got about 50 braces, so there's a lot of material needed.
So that's what we're going to do first thing, is mill up some more brace material.
And then we'll start doing beams again.
Okay, so that's our brace material done.
As you can see, I've got quite a few there.
I need about 50 I think, but I should get 2 out of a lot of them.
So that's good.
And they're 1700mm long, 3 inches thick.
And a lot of them will get a nice quarter sawn brace out of them.
So that should keep us going at least.
I can always mill some more.
So yeah, braces, material, done, stacked up, settling down, ready to go.
Well, it was all going too well.
Bearing's just failed.
Just disintegrated.
Which is really annoying, because I ain't going to be able to get a bearing now.
So, not for like a few days.
So that's the good weather gone then.
It's getting really late in the day now.
Just hoping to try and get this stripped off so I can at least assess what's going on with it.
Something's gone wrong.
Yeah, bearing's disintegrated.
Right, that's our milling done for the week then.
Annoying, because I only greased all these, look.
Literally greased them the other day.
So I've done all my maintenance, and so it still goes wrong.
That's what happened.
The whole thing's sheared.
See that?
It's sheared, cracked.
Completely ripped that all apart.
So the bearing's completely come apart.
There's a lot of force on these, because of the huge tension on the band.
So yeah, new bearing.
Okay, at least we know what it is.
I'll get some spares as well when I order them.
I got really, really lucky, and I found a place that stocked the bearing I needed, which is rare for this area.
And I went out this morning early, got one, got it back together.
Just got the blade on, it's tracking properly.
So we're back in business. We can carry on.
Right, I've got a bit of an issue.
I just was meant to be filming, but I didn't film.
But I've just got these getting a bit precarious, this log pile.
So I've just dropped these logs down here.
I've got everything set up to try and stop logs rolling too far.
I've got to try and get that big one there down, without it going flying and knocking everything off the mill.
Right, this is a bit dodgy.
There we go.
Morning, everyone. Another day.
Still dry, which is really good. I've been lucky so far.
The ground's getting a bit churned up, but for this time of year, it's not going to get better than this, because it's frozen now.
Just loaded a nice log up.
I'm going to get a 200 by 250 out of that, which is 8 by 10 in inches.
And I've got five logs lined up, which shouldn't give me any trouble.
We've got no ring shake. They're nice logs.
So, yeah, we should get nice five logs done today.
That would be nice. Nice five logs in the pile.
Or about 1,500 quid's worth of timber, if I was to go and buy it from the sawmill.
Let's get to work. More milling.
So the pile's growing. Nine there now.
So from the mill that's closest to me, these have cost over 300 quid each.
I think they're actually about 320 quid plus vat, so that's actually close to 400 quid.
That's quite an expensive mill.
I think the best you'd get these for is about 250, 200, 250, something like that, for a timber this size.
And they cost me 60 quid in wood, and I've got all the offcuts for firewood.
There's a lot of money's worth here, if each one of these is 350 quid to buy.
So, yeah, save myself a lot of money. I'm saving over 100 quid on every one.
And plus I get all the offcuts and firewood.
But it's a lot of work.
But yeah, have some lunch and then try and get another couple on here today.
But ten is what I need for all the posts.
So that would be a good start.
That's why I warned you.
There we go.
Yeah, that'll keep me going for a bit.
Yeah, that was exactly why I warned you to get out of the way.
There we go.
That's what I wanted to do.
We're safe now.
So a couple of days now, haven't done any filming.
I've just been milling.
Same thing, you know, it's hard to make too much entertaining content.
Just same thing over and over again.
As you can see, I'm really getting through the pile.
And, yeah, the timber's pile is growing pretty quickly.
So, yeah, there's the 8x8 timbers.
Pile's growing.
There's 16 there, I think, so far.
So they're doing good.
And then we've got...
That's just scraps and offcuts.
And then we've got purlins.
That pile's growing.
And then we've got the big 8x10s.
That pile's growing as well.
So, yeah, still another 50 or 60 logs left to do.
So I'm just going to keep going.
The ground's not too bad. It's quite dry, quite hard.
It's getting torn up a little bit, but it's OK at the moment.
So I'm just going to keep milling.
As long as the weather's good, I'm just going to keep going.
Right, carry on tomorrow.
Morning, everyone.
So it's a cloudy day up here with the sheep.
Carry on milling.
So, yeah, I thought I'd explain a little bit about timbers
and my reasoning for doing things.
So when I bought the timbers,
I bought a 300mm minimum top diameter.
So that's the minimum size at the smallest end.
And with that size, I can just about get 8x8s out of them.
That can go a bit wrong if there's a slight curve
or the heart's off centre, like this one, for example.
You see that heart is quite off centre there.
Now, what we want to do when we're milling for timber framing
is mill this heart.
We want it in the centre of the timber if we can do it.
On this one, it's going to have to be just offset
because the timber's not big enough to get it otherwise.
But I'll get it as close as I can.
And that means that because we've got the heart in the middle,
it means there's no possibility of a knot going all the way through,
causing the timber to be really weak.
And it should contract mostly equally on all sides.
If we had it across there like that,
if the timber was big enough, obviously,
if we had it just on half of it,
it'd have all curved grain through it
and it'd all want to twist and rotate.
So we try to get the timber with the heart in the centre.
But it causes problems because the timbers aren't necessarily straight
and they're not equal sizes on both ends.
So I'll show you how I get around that.
So you can use a laser.
You can have a laser at your blade level
and it will shine down the log,
which is a nice idea, but most of the time,
being outside like this, I wouldn't be able to do that.
It wouldn't be very visible.
It's all right if you're indoor.
So what I do is take the blade to the centre of the tree.
So that's to the pith.
Then I'll mark where we're at, around lumber.
250 there.
Raise it up.
Then we'll go down the bottom.
I've actually already done this.
You see there's a jack under it there.
So we'll go down the bottom of the log, small end.
And then I'll bring that down to 250.
There's 250.
And then see where it's at.
Obviously I've already done this one.
But if it was out, I'd raise or lower the jack.
And the jack just sits on a ledge down there like that.
And I can just adjust it.
So now my first cut will keep that pith in the centre.
So yeah, that's the practice of what I do.
But like I say, sometimes unless you've got huge timbers
and are happy for a load of waste,
then you can't always do it.
Like I'm not going to be able to do it on this one, for example,
because they're off-centre.
If that heart was right in the middle, it would be close.
But it will be close.
And it's closer on the other end because it centres a little bit.
But that's the goal, is to try and get those hearts in the centre.
And I'm not doing a great job of it.
And it's not because of my milling technique.
It's because my timbers, the hearts are generally all off-centre,
which is not ideal.
But I'm doing my best, and they'll be fine.
Right, let's get to work.
Dot's over there just getting through some of the firewood.
We're going to have so much firewood.
There we go, that's that timber done.
As you can see, it just wasn't big enough
to get a really nice timber out of it.
The trouble is, normally if the timber's not big enough
to do what you want out of it,
you just mill some other stuff out of it.
The trouble is, this is the size I need a lot of,
and in this length, so I'm going to use it.
The whole building's so overbuilt, it doesn't really matter.
There's still plenty of good timber in the middle of it.
The only thing is, you end up with these curved sides,
and eventually, you know, 50 or 100 years' time,
these corners will vanish.
So there's a little bit more consideration with the joinery
because eventually that corner will go.
But you just try and use it.
You've just got to select your timber when you're doing it
so that that's not going to really affect things too much.
Like I say, most of the good timber is in the middle.
We've just got these little corners.
So this one here will be used non-exposed, internal only,
for something with less joinery in it
and stuff where the shoulders,
if you lose a bit of the shoulder, it won't matter so much.
It's just about timber selection, really, but we'll still use it.
Sorry about the weather. I'm up in the clouds here.
I can see you probably can't see much of everyone.
New day, going to do some more milling,
which I should be doing every day for ages.
Get up, mill, go to bed.
That's my helpers happy.
Good girls.
Aren't you good girls?
Right, so this is a pretty big timber,
so I should be able to get...
The thing is I'd easily get an 8x10 out of it,
but I've got all the 8x10s in this length I need,
so I'll get an 8x8 out the centre
and then try and get a couple of floor joists
or even maybe a purling.
But I don't know about that yet.
That depends on how the log is laid out.
It's got a bit of an off-centred pith,
so it could cause some problems.
I should roll this round a bit.
There we go.
It's pretty close.
I just did that first cut and realised it wasn't recording,
but I just did the top cut, centralised the pith.
Now I've flipped it, so I'm going to take a little cut off of this
and then I'm going to get a cladding board and then a floor joist
and then we're down to the timber size.
So this next cut now I can turn into a...
I can resaw it and make a floor joist out of it.
It's on the floor now, and then we're going to resaw this.
The heart's looking good in the centre.
We'll resaw that into a nice floor joist.
That wasn't that skilful, was it?
Most people would cut that out, I think.
But I don't know if I'm going to be able to turn this
because it's a big flat area.
That's a dangerous old job doing, saw man.
So that's our timber centred to the pith there.
So we'll have an 8x8 down from there.
Big chunk of waste off that, but I can't do anything with this.
So we'll get our 8x8 under that
and then we'll have a...
So we've got our 8x8 there and we've got a pearl in there.
That's good going, really.
You can see the slight curve to the pith in it.
Hopefully it'll stay relatively straight.
I think I've done quite a good job on it.
It's the best I can do with it.
And we've got quite a lot out of it, so that's always a positive.
There we go.
There's our 8x8.
The heart's not too bad.
Obviously it's not quite in the centre,
but that to me is not too bad.
It's more centred up the other end.
If I'd have taken it any farther the other way,
I wouldn't have got this other timber out of it.
So that's something I'm willing to do.
This doesn't need to be this long, so I can cut some of this bark off
and it needs to be re-sawn down 50mm off of it.
So by the time we do that, this will be perfect.
I've managed to get a few extra timbers, so a bit of re-sawing now.
There's our 8x8.
A big one on the floor.
I'll take this off, put this in the pile,
and then put those other two pieces back on for re-sawing.
Now we're just going to re-saw this piece,
which is going to become a purlin,
which will get rid of that bark we had on it.
It's just got to have 50mm off it,
and I end up with a 2x3.
I've got a bad connection here somewhere.
I'll just step on it.
I need to clean my tracks, it's getting a bit hard to push.
So there's our nice floor joist.
That log was really good, that was really efficient.
Floor joist, purlin, and 8x8.
I'm well pleased with that from one log.
I wish they all went like that.
Right, so two weeks work,
and I've done about 25 tonnes of timber,
and turned them all into milled logs,
and even started doing firewood as well.
I'll show you where we're at, show you what we've got so far.
We've got a pile of 24 8x8s by 16fts.
We've got a big pile of cladding,
and then we've got a nice big pile of purlins,
and then these are 8x10s by 16fts.
They're real big timbers, 150-200kg each.
And then we've got 8x8s by 12fts,
and then there's just some slabs,
and a big, big pile of firewood,
which I'm going to go and do a bit of splitting on now.
It's growing all the time, the firewood pile.
It's an unfortunate thing of milling,
you get a lot of waste, but it's just part of it.
It all goes to firewood, and I'll explain that now actually.
So there's probably a lot of you thinking,
why go through three weeks work milling,
and producing all this waste,
when I could just get a smaller diameter round wood,
and do the barn in round wood.
Well there's two reasons.
The first one is that it's time consuming,
really time consuming.
Round wood, doing that whole frame in round wood,
would take more than the three weeks extra,
than it would for me to mill the timber.
The second reason, and the most important reason,
is demonstrable in one of these actually.
The round wood, when you mill,
you mill the sapwood off.
There's the sapwood there.
You mill that off, and you're left with a heartwood,
which is very durable.
When you do round wood timber framing,
you have to make lots of little ledges and things,
and joinery, and some of it ends up being in the sapwood.
And if that sapwood was exposed,
which some of my barn will be,
or exposed to animal poo and stuff like that,
in a barn,
that sapwood will eventually rot.
In a hundred years time, even if it's kept dry,
that sapwood will be gone.
Woodworm and everything will get it.
But that heartwood, which is durable,
in larch and most timbers you use for timber framing,
is not going to rot in that time,
as long as you keep it dry.
So that's the reason.
You mill that off, and you have a more durable timber.
So that's the reason.
Round wood's lovely, it looks great,
but it's very time consuming,
and you really need to just keep it dry,
and only use it internally,
or continuously treat it,
which I don't want to do.
So that's the reason, spend all the time milling.
And I've got quite a lot of round wood stuff,
and I like both.
I like the look of round wood,
and I like the look of traditional timber framing as well.
So yeah, it's evening now,
just going to do a bit of splitting,
because compared to milling,
splitting is really quite relaxing,
and I quite like splitting.
And we've got a lot to do.
I reckon I'm getting about 30% waste,
something like that.
I'm not trying to get every last little piece
out of the timbers.
I'm going for time,
because it'll all go to firewood.
We're just going to end up with years of firewood here.
That was a good shot, wasn't it?
Yeah, we're just going to end up with years of firewood.
With the way the world is at the moment,
having years and years of firewood in stock,
can't be a bad thing.
And the other thing I think of with it is
firewood's a very labour-intensive thing
that's really quite necessary.
If I was to get ill,
or have an accident,
or be out of action for a bit,
having a couple of years of firewood stored up
would be a really, really beneficial thing to have,
so I'm not too worried about that.
You can't have too much firewood.
In the past, we just didn't have anywhere to store it all,
but the barn will solve that.
So yeah,
we're not bothered about making some firewood here.
Alright, I think that's going to conclude the video.
We've got about another week's work on the milling,
and then the milling should be all done for the frame.
Alright, hope you enjoyed it,
and thanks for watching.
