1986 GMC Sierra 400 Small Block Installing new Distributor and Adjusting The Valves

My Brother Donnie
258 followers
Jan 13, 2025
all right folks we are back messing
around with my truck now
when laughs last you left us
we had figured out that we didn't like
the distributor
it looked like somebody had bought a new
outside of the distributor but none of
the stuff inside the distributor was
worth
them so i picked up some of the inside
stuff of the distributor
we tried swapping the cap
it we need a new distributor
it didn't work to our liking yeah so we
went to the store
and we bought a brand new distributor
what do you think about this distributor
donnie
i'll let you know when we start this
thing okay
so it's an excel it says gm hei
which means uh what does that mean it
means high
electronic ignition no means
i can't remember what agi stands for
it's the chevy thing you know
gm agi performance replacement
distributor
by excel turn that box over down let's
show them what all new is in this damn
thing it shows on the back
okay here's what we got oh no this says
available from excel that ain't in it
well here's what we got look at this you
ever seen anything more sexy
than this look top of the line
look at that all new
every little thing on it new
you got a little rubber band even got a
little rubber band look got the gasket
hanging on it new
brand new new vacuum advanced
canister new wiring harness inside of it
so i don't know why look at that
excel replacement for oem
distributor that means original
equipment manufacturer
distributor legal for installation in
all 50 states you know that's very
important to me donnie
i wouldn't want to do anything illegal
got the damn uh paperwork and stickers
and stickers
we got to put the stickers on that's
true got to put the stickers yeah we
might put them stickers somewhere
yeah maybe on my back of our blue jeans
might shove them
all right so we're gonna drop his sucker
in and see if it's if the damn truck
will start what do you think now is it
gonna work
we gotta take it all apart first why we
gotta do that
because i don't know where the damn
rotor is you just gonna guess and see
how to put it oh
yeah we got to take it all apart first
because we all know where the rotor is i
forgot about that
okay well we're gonna take it all apart
first then we're gonna see where the
rotor is
cap gene has showed up to help us out
gene knows all about engines and stuff
okay we have pulled all the plugs and
they all actually look fine
what do you think donnie are they fine
they're
they're foul a little bit they're fired
a little bit but they're not
they're probably not the problem that's
not the problem i think that piece that
was broke off down under the sugar is a
problem
there was a little there was a little
piece of plastic
just laying inside the distributor it
looked like a piece of some kind of clip
or something
right up against the container right up
against the pickup
so all right so we got eight new plugs
in
and uh we're going to put the wires on
by the way look at these plugs
so the part number for an ac delco plug
for a chevy 350 engine
or 400 is ac delco
one so there's probably better plugs but
it's kind of nice going in saying yeah
i'd like to pick up some plugs uh
get me added in part number ones and
they go what
what's part number one the the number
one part go ahead and get me some of
them
all right we're gonna put wires
all right folks it's idling a lot better
now what do you think donny
yeah absolutely definitely idling better
we've got it on manifold vacuum
we adjusted the timing with the vacuum
hooked up and we're at 20
before top dead center and then whenever
you get on it
get it up to about 2500 rpms you get up
to about 32
before top dead center and it's it's
idling pretty smooth a lot smoother than
it has been but there's still a little
bit of a
thing going on so what we're going to
try is messing with the carburetor
again i brought my vacuum gauge where we
can actually do it how you're supposed
to do it
but all right donnie spark plugs are
good
spark plug wires brand new they're good
oh the spark plug is brand new too you
suck
distributor is good coil
spark everything about the spark is good
now we're down to air and fuel or
something internal in the engine
there's two things that it could be i
don't know that it's carburetor i don't
think it's a hardware
because it's running too good at a
powered yeah once you get in it
it it smooths out it's pretty smooth now
it's acting like it's got a cam in it
now
two things the lifters are out of
adjustment
or uh
okay so here's what we're gonna do we're
gonna mess with the carburetor a little
bit let's see if that doesn't
if that doesn't get it we're probably
gonna what do you think now i'm gonna
pop the valve covers off and look at
this because i i'm gonna put new valve
covers on
anyway and then we can look at uh flash
on the on the rocker arms
and just make sure that i think i think
that's where we're headed next
but we're going to mess with a
carburetor
how are they loose tight
are we even getting the oil up there
yeah
so
from yeah
the uh we're adjusting the valves on
this side there's a little tight so
basically with it running you loosen
them up
until they start tapping
tighten them up till they shut up and
then go quarter turn
so we've got this side done we're going
to do the other side next
it did seem like when you was loosening
them up they were running it was running
a little better i could hear the uh
rpms going up and stuff yeah it's moving
out a little bit it should smooth
them out but we'll see it
it'll only take one to screw us up so it
might be on that other side
it did clean up a little bit but this
makes one hell of a mess
because it's spraying oil the whole time
you're working on
so all right we'll put the cover back on
and take that one
all right we put this cover on donny is
now on the second side
he's loosening it
come up here
he thinks they're way too tight
[Music]
[Music]
so
right now we gotta watch it running that
uh all that oil running on the exhaust
manifold
i was doing an el camino an 80
78 el camino and uh
we was doing the same here and all
of a sudden he went woof
about to go caught on fire all that
was burning like hell
was in this guy's garage he went running
out the door i was like what the hell
i'm
sitting there drinking a mountain dew
and i looked down the whole thing on
fire
damn so i took my mountain dew and just
poured it down that exhaust manifold and
put it out
well i look up and here he comes running
in the door with a five gallon bucket
full of water no no
he never did throw it on there luckily
that car is still around
it sounded like it was running a little
better donny after you adjusted them
well hopefully hopefully we get it
so we'll put the damn cover back on it
and then start her up again
see what she sounds like
[Music]
what do you think donnie
he still wants to mess with the timing
and go go twist
i'll tell you what it sounds a hell of a
lot better
i think those valves did need
adjustments
well she got that power
listen let's get your gauge and put on
it again the vacuum gauge
yeah all right on 24
with the vacuum what did we figure out
it's adding events
so you're right where we ought to be
look what happened folks set the
did they see me doing with the uh the
vacuum earlier
i gotta step back they probably can't
hear me
[Music]
okay so the whole thing is
the uh
donnie's killing because he's afraid
that oil is going to catch on fire we're
trying to burn it off slowly
we can't drive it yet or we take it
somewhere and get it hosed off
okay so the whole thing is
we've got this vacuum gauge and it says
right on the gauge how to use it and
everything
you need to be up between
17 and 22
in that green area in that green area is
good vacuum
and so earlier we were not we were way
down at like 12 whenever it was running
like crap
and so it's saying well if you're
consistently low it's probably
it's either ignition timing or your
valves aren't set properly
it actually says a burnt valve or a
stuck valve yeah
so you know so uh
i messed with the carburetor basically
you want to turn the
you want to set both of your adjustment
screws apparently about one and a half
two turns out and then slowly adjust one
of them until you get the maximum
vacuum and then leave it
you know maybe maybe lean it out just
slightly turn it back in until it just
slightly drops
and then do the same thing with the
right one and you're trying to get your
maximum vacuum well
i did my other truck and it's all up in
the green zone
well this one we were way down on like
freaking 12
wasn't even close and so uh
donny says well let's check out the damn
valve so we took off the valve covers
and he set the valves
by ear you know just with a with a
wrench
like you saw and then whenever we put
the vacuum gauge back on it
we're up in like 18 19 freaking
i think it's inch inch pound of mercury
or something like that
oh okay inches of mercury
inch something vacuum but anyway we're
back up in the green zone which we could
not get to earlier
we took we adjusted the timing a little
bit until we got our maximum
i guess we could still mess with that
well he adjusted the timing up thinking
it was going to get more vacuum and we
adjusted it all the way up to about
50 uh before top dead center which is
crazy high now that's it that's at full
advance i mean that's what
that's with vacuum and with the spring
advance inside the mechanical advance
inside the distributor plus initial
advance
which is how you have you turn the
distributor the uh
with that it was making like 12
13 pounds inch pound foot pounds
whatever the hell
it was making 12 or 13 pounds and uh
after adjusting the valves i had to turn
the timing way back down because it
wouldn't start
it was uh it was locking up so i've got
the timing back down to probably 12 13
somewhere in through there
25 26 that uh with the vacuum advance on
it
and all the other stuff so we've got the
timing down and we've boosted the
pressure up yeah the vacuum's up in the
uh green zone where it should be
so you know what i'm gonna do i think i
might mess with the screws we're gonna
have to adjust the
adjust the the carburetor screws again
but they're probably close now
and i'm gonna have to adjust the timing
yeah just so we'll adjust the timing to
get
i folks we don't even know if the damn
timing uh mark that we have on the thing
is right we don't know any of that so
we're just going to do it with the
vacuum
we've been googling it you know google
knows everything
and the whole problem is we didn't start
none of this
yeah we would have started and i could
have said okay the timing chain is
correct
exactly the rocker arms are the right
rocker
here's here's the whole problem we're
making assumptions
trusting people that have already proven
to us not to trust them you know
so like i'm thinking about about the
damn cam you know
we don't know if that cam's worth a damn
we don't know if it's a mild one we
don't know if it's a
like it's it's a it's a real crazy one
it's supposed to be a mild one
but we don't know i mean we didn't have
nothing to do with it and the people
that did it
screwed it up so who knows who the hell
knows
at least if you do it yourself you
screwed it up yourself and then you know
what the hell you must have screwed up
you know
yeah well you know where to begin anyway
yeah i mean
we have no clue all right so we got nude
and by the way
again everything on this damn thing is
new some things of it are new twice
yeah it's all supposed to be brand new
but the distributor wasn't
somebody you know how people are oh yeah
we replaced that that's uh 37
yeah and uh hell they didn't replace
nothing so
maybe they just forgot donny we're
trying
to figure out if they would have just
been on if everybody would have been
honest from the beginning would have
done how to fix it it's like so i'm
paying for all of it
they i tell i'm told we're gonna get a
new distributor
but they did not get a new distributor
they got they got the damn housing the
housing for the freaking distributor and
then everything and it's a piece of crap
well if if you're pa if you're charging
me for it
just go by that damn thing was 130
it's not that big of a deal and we done
spent
probably 300 playing with it here yeah
trying to chase it down when it could
have we could have had a brand new
distributor and then you know there's no
distributor problems
so now we know there's no distributor
problems there's nothing wrong in the
distributor
nope or the spark plug or the spark
plugs and we think we got the timing
right but it's just little crap like
there's a stud missing on one of the the
valve covers
and then instead of getting the nice
studs or even those damn wingnut things
yeah them are fine but that i'm paying
for
or bolts or bolts you know instead of
just getting the ten dollar ones they
get the eight dollar ones that are
pieces of crap
and i'm man i'm telling you i'm gonna go
ahead and say it i'm sick of all this
china stuff
all this china stuff's got to stop
people i want crap made in mexico at
least
if it's made in mexico i'm cool with it
matter of fact
i've been thinking about it i'm cool if
it's made anywhere but china
anyway
so uh we need some we need some nicer
stuff but we're gonna we're about to
cool down here so that it doesn't uh
catch on fire because there's still oil
on the manifold it's burning some of it
off oh there's a vacuum line that's
disconnected i wonder if that's uh
it's broke in half over here that's what
i was tracing yeah i wonder so that's an
open vacuum
i wonder if i'm making the engine run
right
that probably plugged in up over the
brake booster i mean where the uh cruise
control thing is
up there no that canister there
all right we're gonna track this
you gotta remember folks this got
exhausted all freaking over
[Music]
all right what do you think's next
donnie
tcv positive crank
crank case ventilation
little gauge is hot as hell
it's not burning my eyes like it was
before i think i think it's got a bunch
of bad
old fuel in it i mean this fuel some of
it's been in it for years
it's uh it's getting there it's for sure
it's a lot better than what it was
all right what do you think's next on
the list donnie what do i need to order
[Music]
no we already got a motor order that's
in it
i don't know we'll need to check the uh
power steering fluid i think it's out
okay
so we're down to bits and pieces donnie
thanks do you think that do you think
the engine's drivable like that
i think it would be man or you think it
needs some more work i think
you think we drive it till we blow it up
well the tricky is
this thing don't have no miles on it
really no i mean it might have
40 miles 60 miles on it
um so it needs to be driven a little bit
and breaking in
and you know you ain't gonna know
nothing for probably a month
you're driving and getting it getting a
little
pinch worked out all right folks i think
that's it for today
it's hot as hell we're gonna get out of
here tell them
if you like this content give us a
thumbs up
subscribe to the channel and uh we'll
catch you on the next
all right folks we'll see you next time
donnie's gonna try to drive it up to the
gas station just to give it a little
whirl and see what he thinks
let's go chase him down
[Music]
i heard that
all right folks give us a thumbs up for
taking the trouble to film it for you
leave your comments below i'm gonna go
try to catch em wait uh
let up for me huh
