❌ 3 Trimming Mistakes Almost Every Windsurfer Makes

Life Skills
38 followers
As beautiful as windsurfing can be, the equipment and the technique can be quite complex.
With so many different factors combined, well, the possible mistakes are practically endless.
And with all these different factors, somehow there are a few mistakes that I see happen
all the time. They appear across different skill levels and they can seriously impact fun and
performance on the water. Here are the three most common trimming and rigging mistakes and how to
I also prepared a checklist for you guys, which you can take to the beach.
Mistake number one, too little downhaul tension. Here's how you can find your perfect downhaul
tension. One of the most common trimming and rigging mistakes I see is too little downhaul
tension. This is often combined with too much outhaul tension. And while this is a technique
I've recommended to you in a previous video, I will link it down below for using a fin sail on
a foil. On the fin, it's going to make things very difficult for you. Let me explain. So the
downhaul tension is one factor for how much your mast bends and how much the sail at the top comes
loose and therefore how much the sail twists. And the twist of the sail allows the sail to open when
the wind hits your sail. When you start planning, the apparent wind does not yet play such a big
role. But the more you get into cruising speed, the more the wind will come at a 45 degree angle.
And if the upper leech does not open, the sail doesn't twist and you will run into a resistance
very soon. And at a certain point, you will not go faster, but the sail, the pressure will just
increase. The pressure in your sail cannot be transferred into speed. And this also creates
the effect of the nose of the board getting pushed down onto the water surface. And therefore, guys,
the right downhaul tension and the right amount of loose leech is crucial for easy sailing and
maximum performance. The easiest way to find the right downhaul tension and the right amount of
loose leech is when your sail manufacturer gives you indication points in the sail. If you have
that, just make sure to bring the loose leech to somewhere between these two points and just trust
your sail manufacturer. Every sail brand has a different design philosophy, which is why the
perfect downhaul tension differs from brand to brand and also from model to model. You now know
how it feels when you have too little downhaul tension. If you experience that feeling, go ahead
and increase the downhaul in 0.5 to 1 centimeter steps. In case you were wondering about all this
beautiful windsurfing gear behind me, we're in my surf shop, Surf Center. And our big goal is to get
as many windsurfers back on the water as there were back in 1976 when Surf Center was founded.
So besides creating events like the Ladies' Day, the Deafy Wind Experience, our Wing Festival, we have
whatever gear you're looking for from second-hand price point gear to the latest high-end slalom
gear. We ship all over Europe and we make the best deals in the business and we make sure your gear
is rigged well. So yeah, check out our website or just send us a WhatsApp message. The link for
everything is down below. Alright, back to rigging the sail. So increase the downhaul in 0.5 to 1
centimeter steps and do that until you feel that you have the right amount of downhaul. Here's how
you'll know that you have too much downhaul tension. Once you over downhaul your sail, the pressure
point will become very undefined. You will constantly move your sail forth and back and you'll have
difficulty finding the right position. The loose leech will open so much that transferring backhand
pressure into the pressure on the fin will become very difficult. And then the feeling of pressure
in the sail from being in a windhole compared to being in a gust will feel bigger the more you have
your sail over downhaul. And also when entering a gust the board will feel like it wants to climb
and the nose wants to rise. So if these are the problems you're experiencing then go ahead and
decrease the downhaul tension by 0.5 to 1 centimeter until you have the right downhaul
tension and everything feels right and you're not experiencing these problems anymore. But be
careful guys because too little backhand pressure can also be a result of having the harness lines
too far in the back or having too much downhaul tension. Mistake number two, too much outhaul
tension. Here's how to find your perfect outhaul tension. Another frequent misconception is to apply
too much tension to the ropes between the outhaul clew and the boom tail end. I've even seen people
using their feet to apply tension like this and with this approach you're gonna completely lose
all the shape in the sail. But why is the shape and a deep profile important? Well a deep profile
such as you have in a slalom racing sail like this one or a foil sail will give you a more
stable feel. So when you hit a gust for example you won't feel as out of control and everything
will be more stable. A sail with less shape on the other hand is more nervous. Therefore even
maneuver sails are meant to have a slight profile instead of being completely flat. In non-cambered
sails the profile starts shaping once the wind hits the sail. With too much outhaul tension the
sail can't build up a profile. Therefore it's important to not kill the sail with too much
outhaul tension. On the other hand having too little outhaul tension will create an inefficient
profile. The sail will blow up and will not really release tension anymore. Of course this is
something you can do if the wind is not very strong when you should actually be on a bigger
sail to create some more pressure in the sail which lets you plane in lighter winds. A good
rule of thumb for the right outhaul tension is when you sheet in that the sail just touches the
boom. And here's mistake number three the wrong mast. Here's what to look out for when choosing
the mast. It's widely underestimated how much of an impact the right or wrong mast can have.
And that's not only from a performance perspective but actually the right or wrong mast can even
have the same negative effects as too much or too little downhaul or outhaul tension. And as
explained before different brands have different design philosophies. While some brands for example
believe in a mast that should flex more towards the top other brands believe that the mast should
bend constantly. This is a rather complex topic which once was very well explained by Unifiber
in a blog post which i will link down below. But i try to simplify what you need to know. Use a mast
that was designed for your sail. The safest option is to use a mast from the same brand as your sail.
For example you're better off with a perfectly matching 65% carbon mast than with a 100% carbon
mast with the wrong bend curve. And last but not least this tutorial is again available as a pdf
for all email subscribers. In there we also have a checklist for you as well as a chart which shows
exactly what kind of mast you need for which sail brand. So if you're not signed up yet you can do
so below for free or even better become a part of the growing member community. That way you get the
pdfs earlier. We have one coming every single month right now. Some of them have some extra content
for the members. You'll enter the monthly giveaways and of course you're supporting us so we can bring
you more useful information and entertaining content. And with these tips and tricks on how
to rig and trim your sail you'll be safe to avoid the most common mistakes. So now get out there and
have fun!
