DIY Metal Hoop House Build │ Simple High Tunnel Greenhouse

Farming Techniques
10 followers
This video is about how my brother and I built our metal hoop house or high tunnel greenhouse.
This greenhouse has been standing for over 5 years now and it's still going strong and
this was pretty simple to construct and it doesn't require a ton of material.
I'll have a material list and other information in the description so let's get right into
it.
Starting off with the foundation, it's 2x6 cedar boards anchored with 2x2 cedars and
the frame is 12x19 feet and the nice thing about this greenhouse style is that the dimensions
are easily customizable.
You can remove a pole or add a couple more to make it whatever size you're looking for.
The poles themselves are anchored with rebar that's driven into the ground and the rebar
works really well with the baseboards because they keep everything from pushing out and
it gives you a place to attach the plastic when you're at that stage.
Next up is bending the poles.
This is probably the trickiest part of the entire build and if you're interested in a
more in-depth tutorial on how to bend the poles I have a link to a video in the description
so check that out.
But the way Nate did it is he bought this pole bender from Bootstrap Farmer and this
is the 12 foot option and he measured up 9 inches on each end of the pole and we did
this to make sure that we have a flat end on each side of the hoop so it'll sit in the
rebar and there will be a flat section on top so you can run a board across each of
the hoops to connect them all.
One thing you want to be careful of when you're bending these poles is not to over bend them
so you just want to make sure that they're flush to the pole bender and not to pull too
far beyond that because that'll end up kinking everything and we ruined a couple poles that
way.
So hopefully you can learn from our mistakes and not have to learn yourself the hard way.
So once you have your foundation in place and the poles bent the next thing you have
to do is make some hoops.
This is one of the simpler steps all you have to do is slide them over the rebar, connect
them in the middle, and put a screw in to secure them.
These things are pretty sturdy and you can hang on them if you want to test them.
So once all the hoops are put together and in place we ran a 1x4 treated board on top
of everything.
This connects them all and holds them in place.
Now that all the hoops are in place the next thing you want to do is start framing out
the doors and the windows and there's a couple different ways to do this.
The way my brother did it is he attached these boards to the hoop and framed out a window
and door that way and a couple years later when I rebuilt this I did it in a little bit
different way.
I made a hole in the middle of the board, cut it in half to create an area for the hoop
to sit in and I framed out a window using this style and this has worked really well
but there's a lot of different ways you can do it.
If we were building this today we would probably have some sort of 2x4 ridge beam and ridge
beam support but this thing's lasted through a few winters now so it doesn't seem like
that would be a necessity.
After you have the structure built it's time to attach the plastic.
We attached c-channels to both sides of the front and back hoop and used wiggle wire to
secure the plastic that way and we used boards to secure the plastic on the bottom along
the baseboard.
You also don't want to forget to run some UV tape on the outside of the metal hoops
that you have to protect your plastic.
My brother and I used different approaches to attaching the plastic and after seeing
how both of them worked out I would recommend going with his approach which is using a separate
sheet of plastic for each end and for going over top of all the hoops.
Once you have everything in place you can go ahead and secure them using the wiggle
wire.
We used wiggle wire to secure the plastic to the ends of the hoops and we used some
thin cuts of lumber to secure the plastic to the baseboards.
So this is how I put a new sheet of plastic on a couple years later and instead of doing
individual sections I put one giant sheet over the whole thing and secured it that way.
So I would recommend cutting plastics for each end of the greenhouse and then putting
a sheet over top as opposed to just using one sheet of plastic for the entire structure.
So these are the ends of the greenhouse when you use my approach which is one giant sheet
as compared to the ends of his approach which is using individual plastic sheets and as
you can see it's a lot cleaner and there's not a lot of ripples and crevices which just
fill with bugs over the years.
So after that's all done the last thing you have to figure out is ventilation.
We had our window and doors open but that wasn't nearly enough for this greenhouse especially
in the summer.
So we cut a two foot opening on each side of the greenhouse and rolled up the plastic
and then we roll it back down when winter hits.
This seemed to work pretty well for us.
Another option is you can put a fan in there and run an extension cord out but there's
a lot of ways to do it so you just have to figure out what's best for you and your situation.
So hopefully you enjoyed this quick walkthrough on how we put this hoop house together.
Pretty simple design, very scalable, and it's pretty big relatively speaking for the amount
of time and effort that goes into constructing this.
I'll put a link to our other greenhouse builds on the screen right now and the comparison
between all of our greenhouse styles so if you're interested check those out and I'm
going to be coming out with a lot more greenhouse content this upcoming year.
