Unleash Your Creativity: Expert Carving Tool Tips For Stunning Results!

The Story of Ceramics and Porcelain
9 followers
Hi everybody, this is Anne.
If you're a potter, chances are you have your own stockpile of carving tools.
We see them in the pottery supply stores and we imagine all the things we can do with them,
but once they're in the studio, suddenly we draw a blank.
In this video, I'll demonstrate some carving tricks using six carving tools on three simple
designs.
The good news is that you don't need expensive fancy carving tools.
We found a set of similar tools for less than $10 and added the link for you in our description
First, I'll do a simple thin-lined carving.
I threw a vase using a no-grog porcelain and let it stiffen up to leather hard.
To draw the design, I sectioned off the vase with borders at the top and bottom, then starting
at the top, I drew a gently curved line 3 quarters down the pot and finished it with
a flower shape.
I repeated these lines and flowers, alternating my starting points along the top and bottom
borders all the way around the pot.
I then connected stems and leaves bowed out from each original line.
As I came upon an empty area on the pot, I added some extra swirls and leaves until the
design was visually balanced when I turned the vase around.
Next, I added dimension to each line by drawing parallel lines along each stem.
Now I'm going to be using this sharp V-tip carving tool on the pattern.
It glides along the clay easily and the narrow tip helps keep the lines crisp.
I like to hold the piece in my lap for more control.
Notice that the palm of my hand and my pinky are resting on the piece to help steady my
fingers as I carve.
Curved lines can be tricky, but if you take them slowly and confidently, turning not only
the tool but the angle of the piece as you carve, it'll help.
You want to try and achieve a seamless line, so try to carve without hesitation on the
long lines in order to avoid a choppy, messy-looking surface.
If you notice, I'm not concerned about hitting my pencil marks every time.
The pencil marks are there as suggestions, but my main concern is to carve the parallel
lines leaving a raised area in the center.
When inspecting the design, the extra pencil marks can be distracting.
Using a slightly damp sponge, I wiped them off.
This also wipes away sharp burrs and crumbs at the same time.
Notice I'm using gentle motions, not too rough.
Now don't forget about the borders.
Tightly carved borders would create the perfect frame for the fine carved body.
I carve simple lines side by side all the way around.
Notice I leave the piece on the banding wheel and hold it straight in front of me as I carve
so my lines don't go crooked.
I turned it upside down and repeated this for the bottom border.
Now here's the vase.
The straight, ornate borders around the elegant curves on the less crowded body design create
a very pleasing contrast.
The angles of the stems and leaves move your eye around the vase too.
I painted underglaze into the crevices along the vase body, then bisque fired it.
I brushed a stiff white glaze around the border designs, then brushed Amaco Sky Celadon glaze
over the borders.
I fired it to Cone 5 for this attractive look.
Now let's do a medium carved line design.
I threw a shorter vase with my smooth porcelain and let it dry to leather hard.
To draw this design, I used the mark lines along my banding wheel to section off my piece
into thirds at the bottom and top bands.
Then I did it one more time for 12 sections.
I drew vertical leaves from every other mark extending along the top and bottom borders
straight up and down.
I attached alternating stems and berries, connecting each leaf to the one next to it
around the vase.
I'll be using a sort of cocked-over V-shaped carver and a slim circle carver for this design
I positioned the pointed edge of the tool along the pencil mark of one of the leaves,
angled the tool, and carved down the line.
Keeping the tool at the same position and angle, I carved down through the middle of
the leaf, letting the back end of the tool hit the outer pencil line.
Using the pointed end of the tool, I created a slight carving for the leaf veins along
the first side, and again on the opposite side.
Using this technique gives the leaf a little more sculpted, modern look.
I again used the pointed end to carve the stems.
I used the circle carver for the berries.
Using scooping and twisting motions, I burrowed out each one.
I again used the damp sponge to wipe away the pencil marks, the sharp edges, and the crumbs.
Now here's a similar one I finished earlier where I also carved the straight lines along
the top and bottom borders like the first project.
I like the extra detail inside the leaves that the carving tool offers.
And here it is all finished.
I glazed the inside with a white liner glaze.
On the outside, I used Amaco Hibiscus Matte Glaze and fired it to Cone 5.
The glaze highlights the carved areas and accentuates them to continue with that more
modern look.
Now let's go even bigger with our flower and stem design.
I started again by throwing a large vase with the no-grog clay and letting it dry to leather hard.
I'm using a tool similar to the medium carver, but on a bigger scale, and this triangle carver.
Like the first project, I drew a similar simple design drawing a gently curved line from the
border, but ending it this time with bigger round pods, then continuing to fill in the
spaces around the rest of the vase.
For the leaves, I started with the pointed end of the carver along the outer rim of the
leaf and carved down the outside and down the stem.
The angle of your carver will determine how big your divots will be around the image,
whether you like them narrow or wide.
Starting where my first divot ended, again, I held the pointed end along the other pencil
mark and carved the other side.
Using the triangle carver, I held the tool at an angle and carved the inside of each
leaf.
Now for the pods.
I used my larger carver with the pointed end along the bottom inside edge to carve out
the side petals and down the stem.
I then used the triangle carver edge to carve along the rounded outline, first along one
half, then around the other, and joining the line in the middle.
With a pencil, I marked alternating carving lines in the center of the pod.
I used the pointed end of my triangle tool and pulled thin to thick to thin lines inside
the pod.
I did go back and carve a few of the thinner lines to even them up with the other thicker
lines and create more unity.
I used a sponge to wipe away the pencil marks, soften the edges, and wipe away any of the
burrs.
Now here's one I created earlier where I fluted the rim for more texture in that space.
I bisque fired it to cone 04, then glazed the inside and the top border with a white
liner glaze.
On the body, I brushed on Amaco Glacier Celadon to give it a nice light green shine.
I hope these ideas give you a little more confidence to get out some of those carving
tools that you've avoided experimenting with.
Thanks to the newest members of our Little Street Pottery Research Facility team.
If you'd like to join the team and earn a title, click on the Super Thanks button or
the link to buy me a coffee.
It also really helps us out if you hit that like button and subscribe to our channel.
See you next time in the studio!
