18世紀老槍::1790 年代肯塔基燧發槍步槍的射擊和裝彈演示
神和灵之间
8粉絲
256 次觀看·2025年1月3日
Good morning, my name is Steve Sells, and this is Traditional Muzzleloader.
Today, we are in the Cebola National Forest with the New Mexico Mountain Men at their McGaffey Lake Rendezvous.
And today's topic is flintlock rifles.
This is my flintlock, otherwise known as the American rifle, the Kentucky rifle, the Pennsylvania rifle,
or more correctly, the Lancaster rifle.
These rifles were built by several highly skilled gunsmiths in Lancaster County, Pennsylvania.
This one happens to be .40 caliber, which is suited for medium and small game.
It is in the style of Isaac Hayes, who was a rifle builder in Lancaster County around 1790s.
The stock on this rifle is pearly black maple.
The artwork on it, the carving, is reminiscent of that work that Isaac Hayes did.
It's more of a Rococo style.
The engraving matches that style.
And I will try to give you some close-up views of some of the art that's on this particular rifle.
Hopefully you can see the engraving in the brass fixtures.
Some of the engraving and artwork that's in the wood.
All up and down at the entry pipe, along the muzzle, along the wrist, behind the cheek piece.
This is all deep-release carving.
Now, this is not the typical rifle that would have been owned by a common working man.
This is the kind of rifle that would probably belong to a wealthy merchant or maybe a plantation owner
that didn't hunt for a living, but more for sport.
Now, the barrel on this rifle is made by Rice.
It's a swamped barrel.
So the barrel tapers down to a thin section in the center
and then flares back out at the muzzle to approximately the same size as it is at the breech.
And the purpose of that is to affect the balance of the rifle
so that it's not so muzzle-heavy.
But balance is more central to the rifle, which is very good for shooting offhand.
And this rifle was built by Chuck Kinkle, a good friend of mine.
He's a member of the Dallas Muzzle Loading Gun Club.
We used the best parts we could get at the time.
The Ross barrel.
The lock is a Jim Chambers Deluxe Siler lock.
All the brass fitting is high-quality yellow brass.
The thumb piece here is a German nickel-silver piece with my initial on it.
And, of course, Chuck has signed the barrel.
The patch box is released with this little button protruding from the top of the buttstock.
And it will spring open.
And mostly that's for storage.
You can store patches or small cleaning tools.
I happen to keep a few Band-Aids in mind
because I can hardly ever shoot a flintlock without cutting myself and drawing blood on the flint.
So this is our flintlock rifle.
And in a little bit, I'm going to take it out to the range
where we have some metallic gongs set up.
And I'll demonstrate how I load this rifle,
how I prime the lock and shoot some targets with it.
Hopefully we'll get some good footage.
So this is how I load my flintlock rifle.
First thing is measure out your powder charge.
Don't forget to plug your powder horn.
So you pour your powder charge down the barrel.
And then you need a patch and a ball.
For this rifle, I'm using white denim for patching.
And it is lubricated with a mixture of Ballistol and water,
allowing the water to evaporate out of the patching and leaving the oil.
I seat the ball sprue up on the patch
and use the short starter to seat the ball
flush with the muzzle.
Then using the patch knife,
cut the patching off flush with the muzzle.
And by doing it this way,
I always have a perfectly round and perfectly centered patch.
Then with the long end of the short starter,
drive the ball 4 or 5 inches down the muzzle.
And then using the ramrod in the gun,
seat the ball firmly on the powder charge.
So the rifle is now loaded.
Return the ramrod to the pimbles.
And then we'll prime the pan.
Now this particular rifle has double-set,
double-phase triggers,
meaning the front trigger will fire the rifle
and then cocking or setting the back trigger
will turn the front trigger into a hair trigger.
Now once I've got the barrel loaded,
I like to check the vent with a nipple pick or a vent pick
to make sure I feel powder down in front of the vent.
Then with my small dispenser,
I will dispense about 6 grains of 4F powder into the paint.
Now when I'm hunting,
I often prime the pan with 3F,
the same granulation powder that I load the gun with.
But when I'm shooting targets,
I feel that the 4F gives a little quicker ignition,
whether it really does or not,
if it gives me confidence,
it helps me shoot better.
So pushing the plunger in,
I release powder into the pan.
Now you will hear many, many different opinions
on the correct way to prime the pan of a flintlock.
And the best thing I can suggest for you
is when you start shooting a flintlock
to try all those different methods that you hear
and see which one your gun responds best to.
I always like to shove a little bit of that 4F
into that flash hole with my pick,
and then I spread that powder out
across the entire surface of the pan.
Now I do that because
I can never predict absolutely certain
where the first spark is going to fall.
And I just like it when the first spark
that falls into the pan hits powder,
because it goes off fast.
Now you'll hear a lot of people
that will tell you to put the powder
on the side next to the lock
or furthest from the lock.
And you can try all that
and see if your gun responds to it.
But I find just spreading it across
always gives me good ignition.
Now the one thing is
you don't want the level of your priming powder
to be higher than the flash hole.
I like it to be just below the flash hole
so that the hot gases from this priming charge
can travel into the main charge in the barrel.
So now that I've got my pan primed,
I'm going to close the frizzen.
I'm going to cock the flint,
the lock back and set the trigger.
And I'm going to shoot
at this little round metallic gong
that's downrange.
Yeah, good hit.
Well, it's been a lovely September day
here in the forest.
I hope you enjoyed our video
and our shooting demonstration today.
You may want to hit subscribe.
The next video I'm planning to do
is how to disassemble and clean a flint lock
and reassemble it properly.
So until the next time,
shoot straight.
And remember,
keep your powder dry.
