How to Whittle a Simple Dog - Step By Step Beginner Wood Carving Project

Carving Art Channel
11 followers
7 Video Views·Jan 1, 2025
In this step-by-step whittling guide, I will show you how to carve a simple little dog out of a block of wood! This is a perfect project for someone new to whittling and want an easy sculpture to start their carving adventure.
Hey everybody, this is Brian from Carvingisfun and in this video I'm going to show you how
to make a simple and easy dog out of basswood.
This is a great project for beginners and should only take you between 20 to 40 minutes
to complete.
Now all you're going to need is a 1x1x2 inch piece of basswood, a pencil to sketch with
and your preferred whittling knife.
I'm going to be using the FlexCut Whittling Jack right here, which is a great little pocket
knife.
If you want to see some other good pocket knives I have a full video showing off a bunch
of different pocket knives that are great for whittling.
Now if you're following along with the video at any point, if you feel like you're falling
behind I'll have a picture on the left hand side right here that shows you the current
steps so you can pause the video and catch up.
Let's get started over here.
The first thing you're going to want to do is take your piece of basswood and draw out
some sketches on there.
What I like to do is separate the top, middle and bottom in thirds and draw a line all the
way across.
Those lines are going to primarily reference the back legs and where the head is going
to start.
And then from there I will draw lines on the side, not necessarily right in the middle
but a little bit more off to the side that will represent the body for where we're cutting
out and then a little indicator right here for where we're going to be having the top
of the nose start.
Alright, so let's get started.
The first cuts I usually make are detailing out the top of the ears so I'll just cut off
those little corners on the top right here, simple like that.
And then what I'm going to do is start from the bottom of the ears and then go to the
top of the legs.
So what I'll do here is make a stop cut and then I'll make a little sweeping cut right
to where I made that stop cut there.
And I'll do this down to that line that I drew there.
And once I have that part set up I'm going to even out the curve right there to make
it more of a block at the moment because this is going to represent the bottom of the head
and the ears.
So you're going to have the top of the legs and then the sides cut out and then a little
bit of detail out on the bottom of the ears.
I'm going to flip it over and do the same thing to the other side.
So make a stop cut and then a little bit of a sweeping cut to where you made that stop
cut.
And repeat until you have outlined the sides.
And again, detail out the bottom of the ear there.
And then from here what we're going to do is trim off the little edges right here for
the ears because we don't really want it to be pointed on the side.
So cut straight along the grain and trim those parts off just like that.
And now we're going to start working on the face a little bit here.
So where that mark is that you put in for the top of the nose, we're going to make a
stop cut right there.
And then what I like to do is start taking off that front of the wood right here.
This is going to start forming the front of the dog's face.
So I like to make a couple of series of stop cuts and work downwards.
And I like to go right about there.
You don't want to go too far back or you're going to start removing more wood than you
probably need.
And from here we're going to start forming the bottom of the mouth and then kind of sweeping
up and forming the chest of the dog.
So right at the bottom of the line there for the bottom third we're going to make a stop
cut.
And then about the middle right here of the bottom portion we're going to start a sweeping
cut up to that stop cut that you made.
And repeat this a little bit until you've defined the bottom of the chin to about the
same distance back that you made for the top of the face there.
And that's about right.
Alright and then from here we're going to make use of that line that's still showing
and follow the same height of the top of the legs.
What we're going to do is start the cut right here and then end it underneath the neck.
So what we're going to do is make a stop cut on that angle right underneath the neck.
Start from that line and then work your way up.
This is going to further define the neck area for the dog.
And then repeat the step on the other side.
And then you have a general outline of the dog's neck.
From here you can further outline around the side.
Make it so it's tapered.
So it tapers in you can see right here compared to the other side.
We're just going to make it so that it looks like a neck going to the dog's head.
There we go.
Alright from here what I'm going to do is I'm going to take off the point in the front.
We're going to start forming the feet later on but I just like to get that part taken care of.
And then we're going to start forming the face a little bit.
Now this part you don't want to get too aggressive with it if you feel uncomfortable.
Take off little bits of the material and see how it starts looking for you
instead of taking off a whole bunch of wood.
And since this is at a full on 90 degree angle right here
I'm going to start taking the face back a little bit.
So I'm going to come in with my knife and cut a slight angle along that front there.
This will allow you to have a more natural face for the dog.
So it's just not like a block dog and we're kind of looking.
There you go.
So it's not at a complete 90 degree angle anymore.
It's just slightly slanted back.
And then from here what I'm going to do since I kind of want the dog's muzzle to be a little bit
wider I don't want to I'm not going to start taking off too much wood.
Otherwise you're going to start getting a dog with a very narrow muzzle.
Now if that's what you want go for it but for this one I'm going to have a little bit
more of a wider muzzle.
So what I'm going to do is along this line right here where you can kind of see where the
front of the face is showing.
We're going to start our cut there and push in just a little bit.
And then we're going to come in at 90 degree angle and cut right there.
This is going to define the face.
Then we're going to do the same thing to the other side.
There you go.
And then from here we're going to kind of shape out the face a little bit.
So what I'm going to do is take this squared face that we have here and then kind of put
a little bit of an angle on it.
We're going to detail this out a little bit later but for right now it's just to help
use as a reference.
And then instead of having this super pointy nose we're literally going to chop out the
front of it.
Just like that.
Now you can take yours back a little bit more if you so so desire.
I think I'm going to do it right about there.
And then from here we're going to start kind of rounding out the muzzle so that
instead of it being squared you're going to start cutting angles into it so you have
more of an angle to go by for smoothing it out.
So we're just going to go in and cut at a slight angle on the top of the nose right
there and then cut it off.
So what it is is you're going in at an angle right here pushing back to about the face
and then coming back at another angle and taking that off.
You can do that to the bottom as well so you have more of a rounded looking face.
Now from here we're going to kind of make the nose a little bit.
I found that the easiest way to do it is take your knife and kind of make an X.
So you literally line your blade up with the corner that you have made here to the bottom
and you kind of just press it in a little bit.
You don't want to go too terribly deep otherwise you're going to have a really big old nose
on there.
So do the same thing to the other side to about the same depth and you'll see you have
about kind of like an X right here.
From here what we're going to do is come in at an angle and kind of shave off the part
that we just did to that kind of stop cut that we made.
Now it is important that you go and go in slowly and you don't really push it in too
far or you might accidentally cut off the nose you just just made there.
So we're slowly removing a couple layers of wood at a time just so we can define that
nose.
Once you do it there you just flip over to the other side and slowly cut to that stop
cut and then you made yourself a quick little dog nose.
Very easy.
And from here we're going to kind of round out the face a little bit because it's a little
bit of a square by a sharp 90 degree angle so we're just going to go in at an angle and
shave off that that portion.
All right now from here we're going to kind of figure out how you want to do the legs.
I have a couple different samples of how you can do it.
The video I'm going to do here is going to follow this kind of a leg but you can also
but right now the way it's set up you can easily set it up set up your legs as shown
in the second one.
This is going to be the easiest way to do it because all you're literally doing is
cutting back at an angle and for the legs and defining the back legs and then using
that triangular wedge and just putting a split in the middle or if you really want to or
if you accidentally mess up you can do kind of like a super simplified dog which I think
looks pretty cool.
So if you want to go this route too you are able to do it at this step.
All you're really doing is creating a little it almost looks like a sock puppet kind of
dog which I think is pretty cool.
Like I said we're going to try and follow this dog layout right here so if we're going
to do that we're going to need to take the front back just a little bit more.
What I'm going to do is take my blade about right here and lop off the front part there.
There we go.
Now for this you may want to do a little outline.
It'll make it easier for you to find where you need to go.
I like to put a little nick in the middle there and then determine the max height which
I want the legs the front leg to be which will be just a little bit above half and then
I'll make like a little wedge cut out right to it.
And of course this is going to be coming out to the side as well because you can see the
this dog the legs are kind of triangular pointing out to the front so we're going to make use
of this current angle right here.
So in essence this area right here will be cut out.
All right so let's hop to it here.
I found the easiest way to do it is to create these triangular wedges first so I'll take
my knife and I'll cut I'll make little stop cuts by pressing in and then flip the
carving around and I'll start shaving off those areas that I just made the stop cuts
for and take my knife and start shaving off the top and I'll do this until I feel satisfied
with how deep I've cut those those sections there.
So I'm just basically cutting in a V.
You guys might have a tool that makes this easier but I'm just doing this with a knife
here so go in make a little V and the front doesn't have to be completely slanted downwards
slanted back towards the the neck just like I have there you can give them more of a prouder
chest if you want some so kind of like a little bit of a buffer dog so to say.
There we go now that I have a slight wedge cut out right here I'm just going to take
my knife and further emphasize that triangular shape right there.
All right and then from here I'm going to make a
stop cut along that other line that's going back because from there I am going to
be cutting in at an angle here in just a sec.
So what I'm going to do is cut in and I'm kind of like going to sweep the
front in right there so what I'm doing here is I am outlining the bottom feet and I am also
trimming up the the wood so that I can emphasize the the back legs there as well
and do the same thing to the other side make a little stop cut and then a vertical cut going in
and from there we're just kind of rotating the blade around to that stop cut that we made and
we're removing that front section. There we go then we can start detailing out the
the back legs there. From here just take your blade blade tip and just kind of go in at
that angle that you made. I need to make another stop cut like I need to right here. There we go.
So
and there then just clean up the the front portion a little bit more.
This is where I usually don't like to take off too much wood at the
onset just in case if I need to cut a little bit further down.
Find it easier to just take up a little bit more wood later on
than having to reshape the whole thing. There we go.
And then just reshape those front legs there to a little triangular shape again.
And then from here we're going to start working on the back legs a little bit making a little
bit rounder so what I usually like to do is take off that the corner
so it's a little bit more rounded and then I'll kind of lop off the the top here so go up that
and like that. That way it looks a little bit more rounded look a little bit more natural.
And then what I'll do is I'll kind of even up these spots right here so I'll take that back
and just kind of start blending it in. So I take the back just a little bit
and size the neck a little bit more. There we go. And do the same thing to another leg.
There we go. Let's start working on the top of the ears here. So I'm going to take back these
corners that are going forward for the ears and just kind of
knock it back a little bit and I'll start rounding off the top of the head.
I'm going to worry about the back and the tail in a little bit. I like to do this at the end.
Take off some of the extra fibery looking stuff at the top. There we go. And then I'm going to
start detailing up the the backs of the the legs here. So in order to make it look like it the leg
is not just like going straight back I like to put in a side of slight angle cut right here.
So it starts looking more natural looking and then I'll define it further back down.
That way it kind of separates the the leg from the rest of the body. So you can see it's kind
of more rounded shape now instead of a triangle going back. So that's just basically two cuts
going in. So again what we're doing is taking an angle going back and then cutting back down here.
So you're defining the top back of the legs and then we're going to define the
back of the legs and separate it from the the body. That way you can see it's in has more detail
to it right there. Probably do and then do a little bit the same to the front there.
This removes some of the blockiness. Yeah that looks a little bit better. All right now let's
work on the back a little bit. So from here you're going to determine where you want your tail to be.
I'm going to have my tail be about right here. So I'm going to make a little bit of a triangular
push cut right into the wood and then kind of from that X I just made I'm going to start from there
and go up. This is going to start off the back of the head. I'm going to make like some sweeping
cuts in there and just separate the tail from the head. Then from here we're going to run off the
back of the head a little bit and then further define where the tail is going to start. So
push in following that line that you just made to make the top of the tail and then
cut off the little bit right there. Then do the same thing to the other side. There we go.
All right now that we've got the top of the tail somewhat defined we're going to start
making it look like it's separated from the body. I like to do just one other cut which is where the
base of the tail is going to be to a little bit out towards the side. I don't like to make it
straight up and down. That just looks kind of funky to me. I kind of want to make it look like
it has a puffier tail so I'm going to cut in at an angle make a little stop cut and then come back
in that from the side to separate that out from the body. Then you're going to do the same thing
to the other side and then come in at an angle and separate the tail from the body on that side.
There you go and you got the basis of the tail going. From here we're going to
further round out the body and separate the features so that they stand out a little bit
more. So you can go in and separate the tail a little bit more from the body and just further
define it. All right from here we have the basic rough out for our dog. All we're going to have to
do now is kind of just finish it up and just go and smooth out any uneven surfaces, round off any
blocky areas. We can define the back of the head a little bit more and also define out the ears a
little bit more. I get that part and for the ears one of the things I found that I like to do is
kind of separate it from the head just a little bit more. So I'll kind of round off the top of
the head so you can see that the head's there or you can leave it in a little bit of blockier
shape. It's completely up to you but if you wanted to separate it out a little bit follow the
what I like to do is follow the sides of the face that we made and then kind of use that as the guide
to where we are going to create the shape of the head. So I'll make a couple cuts there and then
I'll come in at an angle of those cuts I made as reference and then separate out the ears and the
top of the head. So you have a little bit more separation between the ears and the head there.
Just a little bit more defined and you can do something similar to the bottom. What I like to
do is cut back a little bit like little tiny cut back. So what I do is come in at a slight angle
right here, push in and then just cut it off from the front. That way it gives a little bit more
dimension to the the ears. You can also do it on the back of the head as well to
further separate it out. What I like to do is come in at a slight angle right here
and then about to where we have the head defined come and meet it.
And then just round off that corner right there and do the same thing to the other side.
And round that off.
And just clear to find the base a little bit more. And then for the most part you have your dog.
Like I was saying you just need to round everything off. Probably round off the base a little bit.
There is some of the fuzz. I'll probably lop that off just a hair. All right and smooth everything out there.
And that's the basis for your dog. From here what you can do is just start
smoothing stuff out. You can make it as chunky looking or as smooth looking as you want.
That's completely up to you. I kind of like the way that this one looks right here. It's very
simple looking. I think it I actually kind of like it like that. I kind of like the blocky look to it.
But from here what you can do is just again smooth it out. You can finish it up with a
and then you can cover it in whatever kind of protective sealant that you want. I'm going to
cover mine up in some beeswax because I kind of like the way that the wood looks it by itself.
I don't like painting my my wood carvings if I don't have to. So I'm going to use
some beeswax paste. Close this guy up and take these off.
Now if you're using beeswax paste it's pretty dang easy to apply. Just
stick your finger in there and scoop some out and apply it like lotion.
It's non-toxic or at least this one is right here from
Interstate Woodworks. It's basically beeswax and mineral oil.
Great for kids. Great for beginners. Super easy to apply. Protects your wood carving and
it also smells like honey so that's an extra bonus. Put it on. Rub it in. After you rub it
into all the little crevices you take a rag and you just buff off the excess. Super simple to apply.
The beeswax paste is cheap and it lasts a long time so it's a great option for anyone who's
just getting started. There you go. Add that to my dog collection. Kind of a blockier looking dog
but you know what? I think that's pretty cool looking. Each person is going to carve theirs
a little bit differently and as you can see I've carved several different versions of mine. None
of mine are all the same. I don't really like to go for perfection. That's just me. I like
having each individual or each kind of carving looking a little bit different. It just gives a
little bit more character to it. Even this one, I think my cats liked it a little bit more than I
did too because I looked away and they got a hold of it and one of them chewed them up a little bit.
Maybe he just doesn't like dogs. Who knows? I have a whole bunch of other videos on here that are all
about showing beginners how to carve different things so if you like the video feel free to
like and subscribe. I have a bunch of other videos you can watch as well if you wanted to
carve something else. As always, thanks for watching everybody. I hope you have yourself a great day.
