Learning the Art of Fan Carving (Carving Birds)

Carving Art Channel
11 followers
We've got, I don't know, doves, butterflies, hummingbirds, unknown birds.
I have become totally obsessed this week with fan birds. Now last weekend the International
Association of Woodcarvers did a little demo, and I'm going to put that link in the description,
but a little demo on fan carving birds. Now I saw birds before, but I just didn't really pay
attention to how they were made. So this is not a tutorial, but I've been dabbling this week,
the typical YouTuber, learn something, make a video, but no,
well, it hasn't been a week, it's only been a couple days, so even worse. But anyway,
I've been dabbling this week with fan birds, so I'm going to take you through the process.
I am not an expert, obviously, and I'm just having fun, and my shop, it's all in my brain,
I was going to make a different video, and I thought this is what I'm doing, this is what
you get. So I'm going to go over to my woodlot superstar here, aka my brother's house, and
we're gonna go steal a couple slices of cedar. Now I have used pine and ash and cedar this week,
and I kind of like pine for the reason that it takes up a lot of water, and I can get it really
juicy, but it's not as strong as the cedar. The cedar has more of a stringy fiber, I find,
and seems to hold the bird together better. So we're going to go with the cedar today,
the ash I didn't really care for because my ash is old and dead, and it just wouldn't take on
enough, and it was a little bit punky too in certain spots. So anyway, we're doing cedar,
so let's go cut a couple slices of cedar.
We got it around here. Some guys like to cut it like so. I'm going to take off that piece there,
but I'm just working my way all the way around, and just using the outside edge and keeping the
center chunk just for firewood, but we're going to take that round edge off, and then we want a
good three quarters to an inch all the way around like so. See that? That way, here, this is the
grain. Yeah, here's the grain on this one. Very, very flat. All right, I don't know if you can see
that or not, but yeah, keeping it flat, and we're just going to work our way all the way around,
and keep chunking them off. I'm making billets probably, oh, I don't know, two and a half to
three inches by three quarters to an inch. I'm going to work them all down to the exact
dimensions that I want, probably with my knife and my draw knife. So that's what we're doing.
All I'm doing is I'm going to, instead of splitting it all up, I'm just going to
take this round part off here like so. Normally, I take a little relief. All right, I can. Let's
take a relief cut out of here. Take a little relief. So there's my edge. I want to go about
two and three quarters, three inches to be safe. All right, a little split.
I'm going to go across. Like I said, three quarters to an inch.
Bob's your uncle. All right, if it needs to be cleaned up at all, we can clean it up,
but this is all going to see a draw knife. This is just cleaning it up really for the pot.
Yeah, that's what we're trying to get, nice little billets. So this tree wasn't super dry,
wasn't super green. It was kind of the middle of the road. We cut it down live. I remember
cutting it down. So we're going to put it in water and put some water back into it. So what I do
is I'll put the, let's make a whole pot, a whole pot of wood, fill that full of water,
and you got to get a rock or something from the garden and weigh it down,
bring the water to a boil, and then simmer it for two, three hours. It's,
some say that the wood has to sink on its own. I didn't find that to be necessarily true,
but you really want to get that wood waterlogged. But today we're not going to do that because it's
30 degrees Celsius here, and Mama doesn't care for the stove going for four hours straight. So
we're going to let that sit, but I'll show you what I do after these are simmered and boiled
or whatever. Take them out. I put them in a Ziploc bag, two in a bag fit perfectly, and
put them in the fridge. If you're going to use them shortly, or just put them straight in the
freezer. And then you've got these prepared. So you only have to do this once every once in a
while. And you got a prepared blank ready for, ready for making yourself a little fan bird.
And that's exactly what we're going to do right now. We're going to take this up to the carving
room and we'll turn this into a bird. Hopefully, like I said, not an expert. I failed to mention
another good resource. I'm going to put a link in the description. It's a couple of fan carving
world from Michigan. Lots of information. So if you have questions about this, probably not the
guy to ask. I've ordered books. I haven't even got them. And yeah, you'll see this again on the
I'm no expert yet, but this is what a prepared finished
wet blank is. So basically the same thing, and this is probably about four times heavier.
So that's all it takes is just get that thing waterlogged. The wetter, the better. So,
all right, carving room. First things first is I just want to get a little flat edge on here.
Okay. Camera. Just getting a little flat edge first.
Spin it around.
Good enough. Got to watch for some little pits. If you pull a grain or something that the,
if there's a little indent, you got to get it up. You want it nice and,
nice and sheer flat, but the other side.
This is not set in stone as a final, final edge, but it helps me,
helps me to see what I got here. So that's nice, nice and straight, but you can see that's all
pretty wonky. So we'll open this way up. I'm going to start flattening it out.
You can see the little, little, any little indent. It's got to, you got to get,
I've got to get it out anywhere that grain is pulled or it's loose. Just got to go.
See that? Digging it right in there. We're getting a little bit thin already.
All right. So now we know I've got a little,
a little indent there. So I'm going to make sure that that's going to be the head end.
Very nice. Very nice. Make sure it's nice and flat profile here.
Yeah. Fairly square. Not so bad. All right. First things first is I'm going to make sure my ends
are fairly square. I see they look pretty good. Okay. Got my little helper here that I can push
against and a pencil works fine, but if you've got an indelible pencil, that works great too.
So I'm going to come in about an inch roughly. Oh, see, that's that mark. That was the,
the head end. So wrong side. I'm going to come in about an inch. I'm going to take my
number 11 chisel. I've already deviated greatly from anything I've ever seen. So
watch, watch a bunch of videos, but I'm just going to put that in here and I'm going to put a groove
right across there. You can see that. Put a little groove there. Same on this side.
This is my lock. This is going to lock all the feathers together.
Now I want it to be about a third.
I want a third left in the middle, I should say. So I'm taking a third off of each side
and leaving a third in the middle. You see that? See some of these feathers, let me show you here.
So this is the tip of the feathers. Now you can do some of these, you can do them round.
See how these are a little bit rounded. What do we got here? We got this little,
I got that tight on there. I got little 45 degree angles also. And then I settled on,
I started doing them like this. You can see, see that? I kind of like that. So all that is,
I'm putting a little mark, say a quarter inch each way, quarter inch each way, like so.
And I'm going to take my little, what do we got here? Anything, anything works,
any gouge works. This is a number eight. I'm just going to line up those two,
two marks, the two quarter inch. I'm just going to run that right across.
Just take that right off of there. It's one side and the same thing on the other,
right across. Just see the water just oozing out. It's a beautiful thing.
And I'll just fine tune it until I got them perfect. If there's such a thing.
Something like that. All right. Not necessary. Like I said, you can, you can round them.
You can take that pencil off. There you go. That's the tip of our feather.
Now what I'm going to do is I'm going to come roughly,
let's just say roughly three inches. I want a quarter inch variance of that. Okay. So
if that's say roughly three inches, I want a quarter inch. All right. I'll just draw a line.
So that's over about two and a half inches, about a quarter inch. All right. I'm going to bring
that line across and do the exact same thing on the other side. A fella who did the demonstration
on the international association of wood carvers, he, this was all knife work to him,
but I'm going to take my number 11 little gouge here. I'm going to run that right across.
This is what we call the hinge. Okay. This is where the, the feathers are going to make their,
make their bend. All right. And I know this is banging the, uh, the camera, but I'm getting
nice and close. I'm just going right across that line with this gouge.
You see that water just so satisfying to carve for some reason. All right. But
we're nowhere near close enough yet. So we're going to take that deeper.
We're not going to go as close as we need to go. We're only going to go
in another eighth of an inch or so on each side. And then we're going to drive the feathers
before we, cause that before we thin that down, because that ends up being just
toothpick size. All right. Let's get this down a little bit deeper.
All I've been doing is taking my big old chisel here
and I've just been going down good. Well, half inch back from there,
pick it up and bring it down. I'm just trying to find the center of that, that gouge mark.
And we're back again. Cut the alarm off. Same thing on the other side, half an inch back or so
coming in on a nice 45 degree angle, hopefully finding the center of that
gouge mark with the other cut and take it off. And that's what we got. All right.
Clean that up a little bit, but like I said, we're going to thin that down
after we split the feathers. All right.
This is roughly a half an inch. You can see how thick we are here and we're going to go even
thinner when we're done splitting the feathers off, but that's your rough length. Now let's say
we want to add some detail to a feather. We can just take our, let's just put one,
this is purely for decoration, run that across. If we want to add something to the feathers,
we'll just take a V tool, put a line around it and we'll just run the V tool across.
And there you can see, you see these feathers here,
see those little V cuts in there, a little extra little detail in there.
All right, let's split the feathers. Now I have all these little draw knives here, but
this one here is a nice straight blade designed just for this purpose. And all I'm going to do,
I'm going to put that on there. I'm going to slide that down right to the bottom. I'm going
to push it over like so, and do it again. And that's okay. You can lose a feather or two on
your journey here. I've made many mistakes and that was no good. I can just pop that out. Do it
again. Keeping these, oh, I don't know, between a 16th, a healthy 16th. It should be wafer thin,
but I know I don't have the knack down just yet to do them all perfect, but I'm trying.
So we're just cutting these down and see how they, just that hinge there, and then they can wobble
each way. So I'm going to go ahead and go all the way through these, trying to keep this as
wrong here. This one here doesn't, yeah. All right. These tall ones. Overall, there is
no feathers. There's one there. That's wonky. All right. Take that one off. That's okay to
take some of these out of here on the ends because we have to do our bird head on here still.
Like I said, if we draw our little bird head on here, we want that to come down a little bit.
So basically these top ones are garbage anyway. All right. Now we want to go like, let's go big
hummingbird. All right. And even up a little bit on the bottom. All right. I'm going to go and
I'll cut that out in the bandsaw real quick and come right back. All right. So there's our,
our bird head. So basically I'm just going to whittle that down. You can see what I said before,
we lost the top feathers because we took the head down. So the first few are good for practice,
but I'm just going to whittle my way around. I'm not really doing a super carving, just kind of
taking some of these edges off. All right. The fellow who did the demonstration
did all this as knife work. So I've already, like I said, I've, I've deviated greatly
off of the guy I watched doing it, but I think that's okay. Everybody's got to find their own,
find their own style. All right. Like I said, we're not getting too carried away.
When this is dry, you can paint these and do like, pull and pick your bird and
paint it as your favorite bird or whatever. But that's not today. And we know darn well,
any ridiculously sharp point that's going to break. So let's just nip it in the bud right
off the bat. All right. A little saw mark there. Yeah. I thought this video would just be fun.
Just so that, uh, maybe, uh, pique your interest a little bit. Like it did mine.
All right. So like I said, that hinge, we want that hinge just
take my knife. I'm just going to go just a little bit deeper on that hinge.
Careful not to cut through or it's all for nothing,
but very thin, a little bit of a wobble in there. So things that I have to work on myself,
are the, uh, thickness of the wings. Of course I always rush on camera,
but the thickness of the wings is, is critical. But I think that's, uh, that's as deep as I want
to go. You can see how, how thin that is. Back in the vice and, uh, let's put some, uh, let's,
what do you say? Fluff some feathers. See? All right. And let's pull apart. It can only get
better. But I do, I just find this fascinating. So many of these lost crafts that, uh, shouldn't be.
You're just pulling apart, shaping them all locked together. You hear those little cracks
of the fibers. That's totally normal. A little eighth of an inch that we left there. That's just
a hinge. All right. I'm going to put this one back and let's go to the back here. Let's make
a little tail feather. It's always an odd number. That's five, five in the back.
So all together, nice and tight. What kind of a bird is it? I don't know. So I'm going to clean
this up here. Very carefully. All right. So rough, rough birdie, but, uh, it's a bird nonetheless.
All right. One more thing to do and then, uh, then we're done.
Round it around, round it around. That's what that thing. All right. Let's make a little,
little eye hole. Okay. Then I'm going to take my little
trusty ice pick. I'm going to jam it right in his head. All right.
Stick that wire in there.
It's so waterlogged. I can actually, oops. I can actually push that in there.
Just like a nail. It's way too long anyway. All right. Stick that right in his head.
And then as that dries, that's only going to get stronger. Okay.
There we go. A little hanger for our bird. And this is, this is crude and all, but I'll just show
you. You can play with that wire to find the balance where you want the balance to be. But
actually that's pretty much banging on. So there you go. How fun is that? We have a little, little
bird, one piece of wood. All right. Like I said, this is not going to be the last time you ever
see this because like, as you're aware, I'm very green and new at this, but yeah, that's dry. That
was made last night, but that is all dry already. So really fun. Look at that. So cool. What a cool
little project. So I made, like I said, I don't know what kind of bird that is. Just some kind
of bird. Bigger, bigger tail on it. I made a butterfly. A little butterfly.
It's kind of fun. You can hang these in the garden. You can, like I said, you can,
you can paint these. I don't know why I tied this one. I'm going to cut that off there.
You can paint these and hang them in your garden,
hang them anywhere. Give them to your kids, mobiles. There's stories. There's quite a
traditional story about this, but I won't even get into it. But if you hang these in your house,
it's a kind of a good luck thing. But some, some simulate it with the, the Holy Spirit
dove in your house too. So all kinds of stories, but man, I just became obsessed over the last
little bit and super fun, super cool. Like I said, I'm putting the links of people who know
what they're talking about in the description. I've got the International Association of Wood
Carvers and I believe it's the NYE, the Fan Bird, Fan World, Fan Bird World Carving. Anyway, whatever
links are in the description, check them out. And like I said, if you've got questions,
go to them. I've ordered some books. There's some really, really cool things that I'm going
to attempt anyway. I've seen women carvings with the dresses of fans, little flowers and all kinds
of stuff like that. So yeah, just a little taste of something totally different for me and you,
hopefully. And yeah, so that's all I got. Thanks for watching. Thanks to everybody who bought me
coffee this week or purchased merch. Always appreciate it. And we'll be back with something
different sooner than later. Thanks for watching everybody. Have a good day.
