意大利布雷達M37重機槍【被遺忘的武器】
甲熊LYB
10粉絲
187 次觀看·2024年12月24日
Hey guys, thanks for tuning in to another video on ForgottenWeapons.com
I'm Ian McCollum, and I'm here today at Morphy's
Down here in the corner
Behind this rather large Italian machine gun
This is a Beretta Model 37 that we're taking a look at
And it's not a gun that gets much known in the US
It's not a gun that gets a lot of respect even when it is known
But I don't think much of that is deserved
This is actually a darn good machine gun
Now, the best way to think about this probably is
In terms of, this is Italy's equivalent to the Browning 1919A4
They're both basically a big box with a barrel sticking out one end
They're intended to be
At the time, they probably would have been called heavy machine guns
Because they were only intended to be used from a tripod
They're fixed position guns
Today we think of a heavy machine gun as a large caliber one
If you go back to World War I and World War II
A heavy machine gun was a static machine gun
Typically belt-fed
Either with a very heavy air-cooled barrel
Which is what we have here
Or with a water-cooled barrel
The Vickers, the Maxim, those were considered heavy machine guns
Today we have squad automatic weapons
We have general purpose machine guns, GPMGs
And the GPMG is sort of the role that this would fit into now
Or a medium machine gun
At any rate, it's not meant to be fired by one man on the assault
It is a fixed position gun
This was run by a crew of three
Supported by six men carrying and supplying ammunition
So in theory, one of these, you've got nine men
Actually working this gun to keep it running
Again, not that much different from a Browning 1919A4
It requires a tripod to use
Unless you're just slinging it from the hip like Rambo
It will support an attack
It can form a key point of a defensive line
That's what these guns were meant for
Now, Breda began development of this in 1933
Although it wasn't developed from scratch
Breda had already done a very mechanically
A pretty similar gun in their PG rifle
Which is incidentally the first rifle produced
With a burst fire mechanism instead of semi and full-auto
I have a separate video on the PG if you're interested in it
Once we get done with this one
I bet you'll find that interesting to see
The similarities in the working mechanism
Anyway, the gun is formally adopted by the Italian army in 1936
As the Model 37
The first order is placed in 36
The first couple of thousand guns are delivered in 1937
And functionally like this is intended to replace
The Fiat Model of 1935
The Fiat was essentially a belt fed conversion
Of the old Fiat Ravelli 1914 guns
Which feed from this really goofy
Mouse trap box like cube mag system
It's kind of a unique thing
I also have a video on that gun if you want to see it
Although I don't have a video yet on the Fiat 35
Anyway, the Fiat 35 was sort of an interim adaptation
This was the long term solution
To a medium slash heavy machine gun for the Italians
Also important to point out that the Breda 37
Was developed for the 8x59mm cartridge
This is a fairly obscure unknown cartridge in the US
Because it was only ever used in just a couple of guns
Essentially after World War I
Italy decided that they should go to a two cartridge standard
Think of this kind of as like 5.56 and 7.62 NATO
Your rifles use 5.56
Your heavier machine guns
And your squad automatic weapons use 5.56
Your heavier machine guns that are emplaced on
Tripods or in turrets on vehicles
They use a heavier cartridge
Because they have the potential to deliver
Accurate effective fire to a much longer distance
Than something that's being fired from the shoulder
So 1,000 perhaps even 2,000 metres
For area effect is a realistic idea
With a gun like this mounted on a tripod
But if you're shooting say 6.5mm Carcano
Which the Italian army was using when this was developed
You don't have, you lose a lot of the potential
Because of the light bullet
Of a small diameter cartridge like 6.5
So the idea was we'll have a heavier cartridge
For our heavy machine guns
And that was the 8x59
The Fiat Model 35 used it
And the Breda Model 37 used it
This was a 210 grain bullet
Running at 2,600 feet per second
So it was fairly comparable to 8mm Mauser
And it's worth pointing out that 8mm Mauser
Especially by World War II was running a heavy bullet
That was intended for long range
It was intended to be ideal for the machine guns
And then functional for rifles
This is the classic choice that military forces have
Do we run all the same cartridge and all of the guns
And accept that it's going to be
Inferior in one of the applications
Or do we split and supply logistics
For two separate cartridges
So that we can have very efficient rifles
And very efficient heavy machine guns
Anyway
There was a brief consideration
Of converting these to 7.35 Carcano
In early in World War II
The Italian army ... tried to convert to 7.35
And that would have been a universal cartridge
It didn't work and they kind of pushed the
Oh no, go back button
And went back to 6.5
It was a bit of a snafu
At any rate, the Breda 37s were always in 8x59
Now this particular one has actually been
Re-chambered for 8x57 Mauser
Standard 8mm Mauser
By an owner here in the US
So that it can be shot
Because there is no 8x59 ammo available these days
Anyway
The next thing that we need to talk about
Before we take this apart
Is the 20 round feed strip
Feed strips were a well-known
Feed mechanism at this time
Of course like all of the Hotchkiss guns
Used feed strips
Those are best known as being
The French army machine guns
But they were also used by a lot of
Smaller client states
Who bought guns for export
Feed strips have benefits over belts
In that they don't tear
They're much less susceptible to degradation
They're not susceptible to water
Unless, well
To moisture
In theory you could eventually have these rust
But that takes a while
And it's pretty obvious
The problem you get with cloth belts
In wet weather is that the belts will swell
And then dry out and swell
And if they're too swollen
You can have cartridges that are held too tightly
And won't feed
Over time you can have problems with the belts
Then stretching
And when they're dry
They won't hold cartridges tightly enough
And rounds will move
Get out of alignment and cause malfunctions
Or just fall out altogether
Metallic feed strips solved a lot of those problems
And the problem that a lot of people
Have with them today
The objection that people have to them today is
You've got a super heavy machine gun like this
With a massive barrel
It's a 42 pound gun
But it's only got a 20 round capacity
Like what a waste of potential
Because a lot of people are looking at these as
OK, let's say I go and get one of these for myself
I'm feeding it 20 rounds at a time
In reality, like I said
There's a nine man crew running this gun
Six of them supplying strips
And three of them actually running the gun
You have an assistant gunner
Whose job is just to stuff new strips into the gun
This essentially is going to fire at the same cadence
As a belt fed gun
Because changing belts is a much more time intensive operation
Than just stuffing another feed strip in
All you do with this
Is you wait for one feed strip to be mostly done
And you just slide this in right behind it
And the rate of fire is essentially
Unimpeded by the change
So strips for the Brita
Hold 20 rounds
They're nice solid strips
They're a little more solid than Hotchkiss strips
And the one really interesting thing about this
Is the Brita actually stuffs the empty cases
Back into the strip
Before it kicks it out the other side of the gun
Now why was this done?
The best reason I've come across is
The Italians simply wanted to
Be able to reuse their empty brass
It was a valuable resource
And they didn't want to have it all dumped
All over the ground everywhere
Presumably mostly during training exercises
When it's not that big a deal
To be picking up your spent brass
In actual combat
Guys are maybe a little less likely to
Get every one of these that they need
Because they're supplied with a ton of them
The story that this was done
Because the vehicle was developed for
The gun was developed for armored vehicles
And you didn't want brass cases
Bouncing around inside
That sounds good
But there actually was a specific vehicular
Version of this gun made
The Brita 38
And it used top fed box magazines
And it did spit cases out
All over the place
So I think this really was more about
Preserving and keeping brass
So that it could be reused
Either not necessarily reloaded
But the brass itself reused
And not just thrown away
Anyway, let's dig into
How this works
Because it's a really impressive gun
It's reliable, it's accurate, it's durable
And it's well built and well designed
We will start with the markings here
We have machine gun
Brita Model 37
Serial number 31000 and change
Made in Rome at the Brita factory
And then the date of manufacture is 1942
Which is also the 20th year
Of the fascist government in Italy
Which was marked on a lot of their firearms
During the fascist period
The tripod here is actually
A Portuguese contract tripod
So it's marked slightly differently
But it's still machine gun
Heavy Brita
7.9mm
938 is the Portuguese designation
M938
Adopted in 1938
The tripod itself is heavily derived
From the Austrian Schwarzlose tripod
It's a pretty good system
We've got extendable legs
On the front so you can lift
The whole gun up or down
You've got these bars
That just unlock back there
So you can fold the legs back
But when locked in place
These give them a good amount of stability
There are a pair of
Locking levers here
So this one allows me to just
Pivot the gun up and down freely
And this one
Allows me to pivot the gun
Side to side freely
You can lock those in place
And then you have dials here
And here
For fine adjustment of elevation
And windage
We have a pair of spade grips
On the gun and a thumb trigger here
There is no semi-auto functionality
So the trigger is full auto
There's a safety
Which is just this little bar
So you've got S for safe and F for fire
And literally all this is doing
Is just preventing you from
Pushing the trigger in
So very simple safety there
The charging handle is right here on the side
Lock the bolt open
Push the charging handle forward
It is an open bolt firing gun
So bolts open
When I pull the trigger
The bolt drops and fires
We have a rear sight here
That lifts up for use
And then I can either
Push this button in
And freely
Slide the rear sight notch
Or I can use
The screw wheel at the top
To give it a precise fine adjust
That is calibrated out to
2800 meters
There's also a rear sight notch
Right here so that you can also use it
With a point blank zero
When the sight is folded down
We have dust covers on both sides
Of the feed tray
Entrance and exit
Because of course
This feed strip
Which by the way goes in
Cartridges facing down
It's going to slide in there
And it's going to come in this side
And go all the way across
And get spit out the other side
Full of empty brass
Now there's one other control lever here
And it's this guy
That actually locks the top cover down
So you don't need to open the top cover
To feed a new strip in
But you do if you need to address a malfunction
Or disassemble a gun
And to do that you first flip this
To the forward position
Then you can grab
These two serrated grasping pads
Lift up
And the top cover opens up
The top cover actually opens way way up
Folds all the way forward
Like that
Now to disassemble the gun
The first thing I need to do is pull out this pin
It is captive
And all I have to do is
Pull it out like that
Then, and by the way
I want to make sure the bolt is forward
Which it is
Then I'm going to push in on this
Which is the end of the spring
Buffer assembly
I'm going to push that in
And then lift the spade grip assembly up
So this collar right here
Locks in
And just locks
The spade grip assembly in place
By the way right here
You can see exactly how the trigger works
When I push the trigger
It just lifts these two hooks up
These are holding on to the bolt
That is the sear engagement surface
So when I lift that up
The bolt just goes forward
And because it is full auto
It will continue to cycle back and forth
Until it runs out of ammo
Or I let those hooks back down
The rest of this process is super easy
All I do is pull the charging handle back
And I can pull
The whole bolt, gas piston
And spring assembly out of the gun
A couple other elements to show you
Before we move on
The feed tray
The right side just lifts right out
It's got a pair of
Little tabs right there
That slide into grooves in the receiver
On the left side
We actually have a spring lever here
I have to pull this in
In order to slide this side of the feed tray out
This is also a locking lever
So when the feed strip is empty
This prevents the bolt from being
Dropped forward
So you don't have to re-cock the gun
When you put in a new strip
This locks it open until you put in a new strip
And then hit that lever
And it will release the bolt
And I can also
Lift this side right out of the receiver
So that's handy
Especially for packing and transportation
It makes the whole gun about
Well, less than half as wide
As it otherwise would be
That rear sight is paired with this
Truly massive
Triangular front sight there
One last simple control here
We can remove the barrel
By pulling this
Pin out to unlock it
Rotate it up
And then I just rotate the barrel
The barrel assembly
Comes out
We've got a basic cylindrical flash hider on there
We've got our gas system
This is a very heavy barrel
Because that's how it
Stays cool
It's just by having a lot of mass
We have an adjustable gas system
So you can tune
Technically you can tune the rate of fire
More importantly you can tune it to be
Reliable with whatever batch of ammunition you have
And this is just held in
By a set of interrupted threads
So a really easy
Interchangeable barrel
They did actually have a tool
That held on back here
To take the barrel off the gun
When it was hot
I don't have that tool here
But you don't need it when it's cool
So that leaves us with just essentially a box
And by the way
This attaches in a very cool method
To the tripod
Instead of having a couple of cross pins
Like we're used to on
British and American machine guns
We have a locking lever
Well we have a locking crank
And a locking lever here
I'm gonna unscrew this just slightly
There's a little press clamp up here
That tightens everything in
And then I rotate that 180 degrees back
And the gun
Slides forward and lifts off
It just has a dovetail bracket here
And
That
Locks into that cutout there
So in a lot of ways
This is actually simpler, better, easier
And you can see the cut there
So when I turn this crank
I'm actually squeezing the front of the mount
So that
Is really easy
To lock in place
The gas piston here at the front
Is pretty self-explanatory and simple
The spring assembly
At the back is the same
This is our main recoil spring
We have a much heavier buffer
Spring here
So the last impact of
Of this assembly
On the end of the receiver
The energy gets absorbed there
Instead of battering the gun
Alright, so what we have here
We have a bolt
Bolt carrier with gas piston of course
And this is essentially our ejector
Now this is very reminiscent
Of the Breda PG
If you go look at my video
On the Breda PG rifles
You'll see they have the same
Angular travelling system
Now the firing pin is a little bit different
In that on the Model 37 here
This by the way
Is the locked position upward
And this is the unlocked position
So when it comes to here
The cases in
Our extractor grooves
Here sitting on the breech face
This is going to
The bolt carrier is going to slam forward
And that fin hits the firing pin
Right here
Pushes in the firing pin
Fires the cartridge
Then gas
Once the round's fired
Gas is going to push this whole assembly backward
While the bolt stays in place
So there's a little bit of travel here
Where it's just going straight back
That's the dwell time
So that allows pressure to drop in the chamber
To a safe level
Then the bolt hits the angled section
Of this track
And it starts to drop downward
That is unlocking it
So that the whole thing can travel backward
And you can see that the extractor here
Is going to go from that position
Where the cartridge is
Fully in the case
In the bolt face there
And as it travels
This is going to push the empty case up
Out of those extractor grooves
So what that's going to do
Is of course
Free the empty
It's going to pull the empty case out
And then it's going to free it from the bolt face
So the bolt face can pick up the next cartridge
However
There is one little bit
Of extractor lip on the top
Right there
And that's going to stay hooked into the case head
And it's going to pull the empty case back
Out of the
Well, it's already out of the chamber
Because this is pulling back
As it unlocks
But it's going to pull the empty case back
Into the feed strip
So the cartridge was initially
Pushed out of the strip by that fin
And then
As this comes back
It's actually putting the empty case
Back into the feed strip
The whole time that's happening
We have this lug right here
That's operating the top cover
And by the way
This lug is spring loaded
So that you can close the top cover
In any position
And this will just snap into place
When it's lined up properly
Like that's a feature
That a lot of World War 2 guns didn't have
Let me show you where this is in the top cover
Inside the top cover
We have this reciprocating slide
And it controls
The feed pawls here
So you can see this track is straight
All the way until the very end
When it has a little dog leg
So when it's all the way back
It's going to pull this feed pawl out to that side
And then when it moves forward
It pulls it back in again
And that is going to cycle
The feed strip in one position
Now you can see this hole up here
That is where this lug sits
And so as the bolt assembly
Bolt carrier assembly
Goes back and forth
It is pushing this
Back and forth
And at the very end of travel
It cycles
So it's during this section of travel
That the empty case
Comes back out of the chamber
It's put into
The now empty position in the feed strip
And then
At the very end
Once the empty case is in
Then the feed strip is cycled one position
Well, these lugs come back
They hook on to the next set of notches
In the feed strip
Because they are hooking on to
These notches
Little bumps
And then they are going to pull it in one position
Now there is a live round
In front of
This fin
And as the bolt carrier goes forward
This is going to strip the round out of that
Position in the feed strip
Into the chamber and repeat the whole cycle
So that's the Breda 37
All the way field stripped
This is a remarkably
Simple, durable, effective
Gun
It was really well liked in the field
It was well liked by the Italians
It was well liked by the Germans as well
These were used by Allied troops
When they had the opportunity
When they captured a gun and could put it to use
They did
The guns were accurate, they were durable
Really, it's a vastly underappreciated gun
In part because of those feed strips
And in part, I think, because of its rarity
We just have very, very few of these
In the United States
Manufacture of the Breda 37
Ran from, of course, 1937
Clear until, well, in fact
After the Italian armistice
In late 1943
Production was pretty hefty on these
By 1942, they were building
1,000 a month, that picked up even more
First quarter of 1943, they did
4,000 of them
In addition to purchases by the Italian army
These were also adopted by Portugal
As the M938
I don't know exactly how many Portugal bought
This is actually a Portuguese tripod
On this particular one right now
But sold to Portugal as well
After the Italian armistice
Breda did continue to manufacture them
For a time for Germany
And the Germans would get something like
1,300 of these
Specifically made for them
There was some talk at one point
Of expanding manufacture
Beyond just the Breda factory
So that they could increase production even more
But that never actually happened
All of them ended up being manufactured
By Breda
And it says something about the quality
And the utility and durability of the gun
That it actually continued in Italian military service
After World War II
Into the early 1950s
Eventually the Italians would adopt
A copy of the MG 42
But this was
We're talking close to 20 years
This was the standard Italian heavy machine gun
Anyway
These are extremely scarce in the US right now
There's something like less than half a dozen of them
That are transferable on the US registry
So very cool of Morphy's to give us a chance
To take a look at this one
Hopefully you guys enjoyed the video
Thanks for watching
