Our first dive into suits worn by pilots, in this case ones who flew the Lockheed A-12 which was a part of a top secret proje

Uniform & Arms
3 followers
Dec 22, 2024
Most people are familiar with the U-2 spy plane and the 1960 incident involving the Soviet shooting
one down. However, what's not as well known is that the CIA had only given the U-2 a useful
lifespan of about two years. So what do they do? Continue using it, improve upon it, or build an
entirely new aircraft? Well, actually all the above. As soon as the U-2 took flight, the CIA
got to work on another aircraft, the A-12. With it requiring new specifications, a new suit would
also be needed. One that could maximize the efficiency of the craft, while also keeping the
pilot safe and somewhat comfortable. That would come in the form of the S-901 series of fully
pressurized suits. Now before we dive into covering the suits of the Lockheed A-12, we just want to
let everyone know this video is a part of a collaboration with the channel PilotFoTog.
For those of you coming over from there, welcome, and to those who aren't, you should take a look
at Tog's video covering the development, history, and usage of the actual A-12, link to which can
be found above, in the description, as well as at the end. Okay, so let's get right into it. It's
the 1950s, and quite a number of partial pressure suits have already been fielded for various
projects and aircrafts, with a series of full pressurized suits beginning to sprout up come
the middle of the decade for naval use. Now the difference between these two are pretty
straightforward. Partial pressure suits will protect certain parts of the wearer's body up
to a certain altitude. Its main way of attaining this is by compressing the body, thus keeping the
wearer under a specific pressure. This was considered by many as uncomfortable, but made
up for it by way of being smaller and easier to maneuver in. A fully pressurized suit, on the
other hand, essentially covers the wearer entirely and encompasses them in the proper atmospheric
pressure. So even at great heights, their body remains in a safer and more comfortable level,
which in turn can even protect them from cabin depressurization. The downside to these though
was that they were a little trickier to move around in, were heavier, and took up a bit more
space. With the early years of the U-2 seeing partial pressure suits being employed, many felt
that doing the same with Oxcart, the code name for the A-12's development project, would suffice.
This was so much so that the initial proposal presented by Lockheed to the Joint CIA and Air
Force Selection Committee suggested doing so. However, with the A-12 having the goal of flying
3 miles or 4.8 kilometers higher, as well as 5 times faster than the U-2, there were a number
of factors that called for a full pressurized suit. One of the biggest was temperature. With
the plane flying so high and at such great speeds, the heat of the cockpit itself could reach above
100 degrees Fahrenheit or around 37.8 Celsius. Many involved with the physiological aspects of
pilots and aircraft such as this pointed this out as one of the best reasons why a pressurized suit
would be required. Even still, there were those who pushed for a partial suit, but regardless,
the Firewell Corporation, along with the David Clark Company, which had been subcontracted by
them, were hired to design most of the elements related to oxygen systems and protective equipment
such as suits and helmets before the final decision had been made. This dispute between
what type of suit finally came to a head during a pre-development conference hosted by Lockheed for
the A-12. Going in, the CIA was on the side of using a fully pressurized suit. They had conferred
with Brigadier General Donald D. Flickinger, who had worked on the U-2 program and was one of the
CIA's top advisors around this time when it came to the physiological aspects associated with these
types of crafts. Kelly Johnson, one of the lead Lockheed designers on the project, felt otherwise,
believing that a full pressurized suit was too heavy and would just be a hindrance. A discussion
was held between Kelly Johnson, Joe Roussikas, a representative from David Clark, as well as
representatives from Firewell and the CIA, evidently believing the discussion was going
nowhere. Roussikas went to get up and leave, but was stopped by the CIA representative, who then
quite bluntly stated the full pressure suit route was going to be the one they took. This discussion
ultimately helped with the production and efficiency of the plane overall, as it was easier to create a
pressurized suit than an entirely pressurized cabin. In addition, it was calculated that for
every pound or 0.45 kilograms of weight removed, the craft was able to go up one foot or 0.3 meters
in elevation, so every little bit helped. So the cockpit would not be insulated, meaning that the
suit had to do most of the work protecting the pilot. And so not long after, work began and the
David Clark company was contracted directly to make the suit, rather than being subcontracted
by Firewell. Because of this, Firewell was then able to focus more on the oxygen and pressure
elements, such as the suit pressure controls, breathing regulators, and oxygen system. Come
early 1961, the first prototype was made, the S-901 Flying Outfit Full Pressure High Altitude
Multilayer Suit. The primary requirements of the suit alone was that it needed to provide
protection from the hot temperatures the cockpit may face, changes in pressure brought on by high
altitude, and the rapid onset of heat, wind, and eventual freezing temperatures in the event the
pilot needed to eject. These suits were based off ones that had come before it, such as the MC-2,
a suit made for the X-15, the world's first space plane, as well as the AP-22S series of suits,
which were being developed for non-top secret Air Force projects and operations.
Now one of the interesting, and sometimes confusing aspects about these suits was what
they were called. Neither the Air Force nor CIA ever gave them official designations or names.
They were simply referred to by the David Clark Company's model numbers, which oftentimes covered
various parts and elements of suits and other components, some of which were not even associated
with the same project. Anyway though, the first suit was ordered on March 7th, 1960, and was made
specifically for Captain Harry Collins, who was to be the one to test out the suit before full
production on them began. Due to ongoing research, feedback, and development associated with the
program, quite a number of changes were seen to the S-901 over its lifetime. From things as small
as changing neck ring latches the device used to connect the helmet to the suit, from single to
double, to things as large as adding flotation bladders and knife pockets, as well as the
removal of aluminized fabric on the outside, there were quite a number of versions. All in all,
before the suit actually reached a completed point, it had gone through at least 12 major
versions, with the initial ones gaining an additional number, sometimes two. For example,
the S-901-2 or S-970-5-3. Not only that, the S-901 series would also include the addition of a letter,
so for example, S-901B, C, and so on. This, mixed with the various modifications and models being
made for the A-12 as well as the YF-12, an interceptor fighter based on the design of the A-12
that was being tested in the early 60s as well, led to quite a bit of concurrent usage of different
suits during the same time periods. But, the final large-scale version as far as suits for the A-12 go
was called the S-901H, which became the primary one for Oxcart in 1965 and saw quite a bit of
changes to it compared to the original S-901. So let's actually take a look at the general
components that made up most of the suits. Though features vary between versions,
suits generally were comprised of an underlayer. Though not technically part of the suits,
these were essentially a base, usually in the form of olive green or white long johns,
that added a bit of comfort for the wearer. An inner suit, sometimes referred to as the gas
container layer, these were basically a garment made up of a waterproof material that inflated
when under pressure. These went from the wearer's toes all the way up to their neck and were the
main component of the suit as far as environmental systems go, as it had most of the connection
points for other pieces such as the helmet, gloves, and communication systems. Versions up
until H were noticeably different as far as entry method. Earlier suits utilized what was called a
U-entry method, which saw a zipper start at the front of one shoulder, then go down around the
back, and then up to the front of the other shoulder. The H model simply took that zipper
and oriented it horizontally along the back, allowing for a much quicker and easier process.
Above that was the restraint layer, used to support and prevent ruptures of the pressurized
section. They too appeared to have had similar entry methods, i.e. the U versus vertical rear.
On top of all this was the outer suit, which is what you usually see in most photos. Initial
versions were made of an aluminized, no-mix fabric, then referred to as HT1, but were eventually
replaced with matte white polyester based fabric, known as Dacron, as the aluminum finish would
cause reflections and glares for the pilots. The Dacron fabric stopped this problem but did not
offer the same amount of protection against fire, and so it had to be backed with HT1,
which added a little to the suit's overall weight. This layer was also the toughest, as it was the
exterior portion, which would face all the elements and interactions with the cockpit,
and in worst case scenario, atmosphere. At some point these also featured a patch that was sewn
onto one of the arms, which highlighted the steps a pilot needed to perform in the event of a bailout.
Much of the earlier versions of all these layers were custom made for the wearers, but as stated
earlier, the later models were made in 12 sizes. Small, medium, large, and extra large, with each
of those sizes offering a short, regular, or long versions as well. Next up was the helmet, which
featured a clear plexiglass, acrylic, and later on glass visor that incorporated a conductive gold
layer which allowed for defogging, but often caused a bit of reflection. Additionally, a tinted shade
visor with adjuster knob for it on the side was seen, and a built-in headset and microphone, which
were attached on the face seal. In addition to being connected by the latch rings, they also
featured a form of cable that held the helmet down when the suit was inflated. These were made in
three sizes, and allowed a bit of adjustment for the crown. Now on to the gloves. Available in 12
sizes, they were connected by way of a mechanical metal ring. These included a neoprene bladder with
the same restraint material found in the middle section of the suit. The outer gloves were
connected by way of zipper, and included various fabric, such as black leather on the palm side, as
well as nylon on the back, a stretchy material known as Helenca for the knuckle section, and
finally the same Nomex as the rest of the exterior suit for the remaining area. They also featured
internal components referred to as brake bars. These allowed the gloves to become clenched after
the suit was pressurized by way of the black straps on the outside. Finally were the boots.
Primarily constructed of soft white leather in seven different sizes, they looked a bit like
US combat boots of the time, though made a bit bigger so they could fit over the inner section.
On the front was an easy on-off zipper, which was surrounded by adjustable laces. Connected to these
by a series of straps, were a specialty set of metal spurts. They would be connected to the bottom
of the A-12 seats for the purpose of keeping the pilot's legs secure in the event they needed to
eject. The total cost for one of these suits? Usually around $30,000. Now for the sake of
covering all bases, here is a very brief rundown of all the alphabetized suits. The original S-901
was the base model used, though not solely to develop all future S-series suits. The S-901A
saw the replacement of dual neck latch rings to a single one, and saw the most amount of insulation
under the cover, which was decreased in all future suits. The S-901B went back to dual neck latch
rings and replaced a back biomedical fitting with a pad. It remains a bit of a mystery as far as
reasons for its development. The S-901C kept this single neck latch ring and also added a double
slide fastener. The S-901D switched brands of the neck rings and updated the forearm disconnect as
well as communications components. The S-901E was one of the most modified of the versions as it
overhauled many aspects and was the first suit to ditch the long name of Flying Outfit Full
Pressure High Altitude Multilayer Suit, which was replaced with the much easier Pilot's Protective
Assembly. This would become the first large-scale used suit, though it was still tailored to each
of the wares. The S-901F, used primarily for the YF-12 series of aircraft, saw the restraint layers
leg section modified for improved comfort, as well as the removal of knife and watch pockets.
They were the first in the S-series to gain general size options for the wares. The S-901G
was mostly the same as the F, but has been considered as a custom-type suit for wearers
who didn't exactly fit into any of the general 12 sizes seen with it. The S-901H was the most
commonly seen suit. Being the main replacement of the E as the general suit of the A-12,
it took a bit more influence from another family of suits and saw the main way of entry change from
a U-style to a simpler back vertical zipper. Additionally, the restraint layer had adjustment
cords on it instead of laces, and it adjusted elements of the venting system. Later versions
would also add a urine collection system, and finally completely do away with the aluminum
exterior for a non-reflective white one, which appears to have been intermittently used with
an assortment of previous models as well. There appears to be no I model, as in many industries
when assigning numbers, I is skipped over as it too closely resembles the number 1.
After this is where things get vastly different, as the next suit was referred to as the S-970.
The overall look and functionality of it appears to be based off the S-901H,
but according to David Clark it was based off the model G, with one of the biggest changes
being the addition of an integrated flotation system. Finally is the S-901J, which is the
odd one out as it was not directly associated with the A-12, but rather YF-12. However,
it would see major use as the go-to suit associated with the SR-71 project that spawned
from Oxcart, albeit in a modified manner, though that is another story. Now again,
these were just some of the larger changes seen between versions. Because of the secrecy
surrounding Oxcart, the lack of information, and just passage of time, covering every single
variant of each version in great detail would be next to impossible. Anyway though, by the end of
the 1960s, Project Oxcart was on its way out, and was eventually cancelled. The A-12 project and
its suits were rather short-lived, yet extensive, though proved vital in the US's development of
high-speed reconnaissance aircraft. The S-901 series, when looked at with just the A-12 in
mind, doesn't seem like much, but when viewed with a larger perspective, proved to be vital in
the development of future fully pressurized suits, such as the S-1030, which eventually replaced all
SR-71 and U-2 suits, as well as the Advanced Crew Escape Suit, used by space shuttle crews
towards the mid-1990s. With so few made in general, today even fewer of the S-901s still survive,
and can be found in a few different museums and exhibitions, with very little making their way
to the collector's market. Well, a bit of a doozy, this one. Hopefully it was enjoyable,
and something of a refreshing break compared to what we traditionally cover on the channel.
Again, we didn't go too much into the actual A-12, so if you want to learn more about that
and the entire history surrounding the project, check out the video Pilot Photag did on it. As
always, be sure to like and subscribe, or just check back real soon for more videos,
right here on Uniform History.
