Traditional Leather Hunting Gear - Possibles Bag - Powder Horn - Knife - Clothing

Jewelry Making
51 followers
Hey everyone, Melissa here. Welcome to my channel and in this video I want to show you my three
favorite chain lengths that I like to make in my jewelry making. So just stay tuned. Okay,
grab your tools and let's get started. You're going to need some wire. Today I'm going to use
18 gauge and 20 gauge round wire, but depending on how thick you want your chain, you can go
larger or smaller with your wire and you get a different look. If you go 16 gauge, you'll get a
thicker, more substantial chain. Alright, let's start making some figure eight lengths. What I
do is I pre-cut my wire ahead of time. I cut them to one inch length. I'm using 18 gauge wire,
by the way, round wire. I cut a bunch ahead of time and I always put one aside so I can use it
to measure against and I always make sure both ends are cut flush.
Another quick tip I want to tell you about is to keep all your little loops the same size
because you can mark your round nose pliers
with a sharpie so you keep your wire at that spot every time and all your little loops will
be the same size. Alright, so I take the end of my wire, put it where that mark you made was,
and start twisting it around. You can use your thumb to push it the rest of the way
from behind there. Sorry, I went off camera a little bit
and do you flip it around and you do the same thing to the other side.
Start turning it and then you can use your thumb to push it along the rest of the way.
If the ends of your loops aren't lining up, you can use your flat nose pliers
and kind of push them together.
So I made a few figure eight links and after some experimenting I figured out that I needed
an inch and a quarter of wire to make the elongated link. I'm going to cut it to that link
and make my loops on the end about half the size of the figure eight links.
So I'm going to make a link on one end, flip it around, and
do the opposite direction on the other side.
And of course I repeat this process until I have enough links to complete my project.
At some point you can start linking them together to make your chain.
Here you go, that's what your chain starts to look like.
For the second chain style, I go ahead and make a bunch of figure eight links ahead of time.
Same as before with one inch of wire.
But this time I take each loop and I give it a half turn.
I grip one side in one plier and the other side in the other pliers and I twist.
And then I go back and close them up.
At some point you can start linking them together.
Keep in mind to open them to the side and not outward. You don't want to misshapen your loop.
The links for this next chain take a quite a bit more wire so I cut lengths of about four inches.
And I just cut a bunch ahead of time.
So about an inch and a half or so down one side I make a wrapped loop.
If you are unsure on how to make a wrapped loop check out this video here.
So at the end of those wraps you're going to make another loop
and do the same thing but this time you're going to overlap your first wraps with your second wrap.
You may need to snip off your wire if you have too much but in this case I don't need to so
I'm just going to bring it around and smoosh it down
smooth and make sure your loops are on the same plane and nice and uniform.
So that's our first link. So from here on out we're going to start linking them together.
So go ahead and you start the process all over again.
Make a wrapped loop.
The key to making chains like this is to remember to add your link in
which clearly here I forgot so I made a wrapped loop and I forgot to add my link.
But that's okay because you can always add them in later if you forget which I always do.
So I'll show you that in a second.
Now that I have two links to incorporate I'm going to
start my third link. Before I wrap it I'm going to add my other link like this.
I'm going to grab it with a narrow chair nose pliers so I don't smash my other links loop.
And I go ahead and make my wrap and I add my link to the other side.
Okay so that's how you link those together.
You can make as many links as you want and you can make
bracelets and necklaces whatever you want. This is a necklace that I had made
with those type of links and here's the other necklace I had made with the other type of links.
Now these are already oxidized.
So those are my top three chain designs that I go to
when I'm making jewelry. So if you like this video give me a thumbs up,
comment below if you have any questions or suggestions, and hit the subscribe button
because I post new videos each week. Thanks for watching and I'll see you next time.
