Making a Violin

Musical Instrument | How It Is Made
138 followers
5 Video Views·Dec 18, 2024
At first I was a little hesitant.
I've never done any kind of woodworking.
Totally doable.
You just need to follow Brian's directions.
He's been doing this for a long time
and he has a really good sense of what will keep you out of trouble.
It's like a dance.
You get into the flow of working with the tools and the wood
and it speaks to you after a while
in terms of how best to treat it.
Hello everyone.
Today's tutorial will focus on making the template and the mould.
Inside the package you received
you should find the parts to make the collapsible mould.
A little packet.
Inside the packet is a drill bit.
Some screws and washers to assemble the mould.
If you're not used to it
you need to get yourself a small engineer square
which you can put there.
Then visually you can watch with your eyes
and you can see that you're parallel to that
just to get a feel of what it's like to file square.
Hold it against the side
and then we're going to be rubbing it like so.
Making sure that it doesn't rock.
That the surface is very flush
against the side of the mould.
You can put it on fairly liberally.
Today's tutorial is going to focus on sharpening.
There are several methods.
This is the grinder which we will use.
Then I've got some different stones here.
There are several options.
Don't worry if you don't have one of these grinders
I'm going to show you exactly what to do
using the stones.
It just takes a little bit longer
but you'll get the same results.
We've finished grinding it on the tormac.
This is a gouge.
We'll take it out.
Then I'm going to show you
there are several ways of sharpening a gouge.
The one that I prefer is this.
I'm going to take a Japanese water stone
which is 1000 grit.
I'm going to hold my elbows
tightly against the sides.
I'm going to hold the chisel like that
with my finger.
Then I'm going to hold this
between my fingers like that.
Then I'm going to come
and instead of moving the tool
I'm going to move the stone
up and down like so.
This is a piece of leather
but it has a round surface
that we've glued on.
Then we're going to put on
some jeweler's rouge
or the green micro paste.
Then we're going to lightly
strop the gouge.
Always keeping it at the right angle
not too high because you're around the edge.
Then you're going to hold this flat
and you're going to rotate it
as you move it slowly.
That's the motion.
You can do it once more time on the front.
There we have it,
a nice sharp gouge.
When I look at this
I see it's going down at an angle like that.
This one's the same angle
which means I need to plane
this surface at that slight angle.
What I'll do is
I'll put it in the vise.
I need to make it a little bit rougher.
Turn it down.
It's nice and sharp.
You can see I'm holding the plane
at a slight angle to match
the angle of the split.
The secret when you're sawing
is not to go frantic like that.
That never really works.
It's rather to push it to the full length
and with the push stroke you give energy
and then the pull stroke
you do nothing.
When working on the end grain again
we use a little bit of water.
Then when we're using
tools in violin making
we try and avoid holding them
really far away like this
because you can slip and you have no control.
We always try and anchor
the tool.
I'm going to put my hand here
which is on the vise.
I'm going to grip the chisel like this.
Then I've got very little motion.
I can only move it
with a lot of force.
Even with this hand I'm pushing
I can only move it about that much.
It's like an inch.
That means we have really good control.
You'll see I have good control like this.
I'm rocking this hand
and I'm pushing with this hand.
We're keeping it very
stable so nothing
is being pushed away.
Now we're going to file a
chamfer on it.
When you're doing it the motion is not
straight but you're always moving it across
slightly so you're doing that.
That way you get a nice flow
otherwise you're just going to get different flat areas.
We can hold our hand
and just lightly rock it.
We can take off shavings like this
until we get to the line.
We're going to slide
in the glue.
You do it a couple of times
to make sure you're getting enough glue in there.
We're going to take our block
and put it underneath.
We have our cork ready.
We're going to clamp it lightly.
We can come with our paper towel
and we can wipe away
any excess glue.
The pegs are made of different kinds of wood.
There's rosewood
which has a natural oil in it.
Then you have ebony
which is beautiful and I like it.
It's quite elegant.
Then you have boxwood.
It's also lovely wood and it's generally a bit
softer and it's used mainly
on older instruments.
This is a block of wood with a blade
and they work really well because they have
more of a scraping action than a cutting
action and you get a beautiful
smooth finish.
Once you have turned it down you should have a reading
of around 8mm.
Once we started getting close
now we do something different.
We're going to turn the reamer the other way
so it compresses the fibres
emulating what would happen
when you put the peg in.
Paper towel and we fold it like four times
and then we give a really
nice big solid rub.
You can hear the sound.
It's really polishing it up.
And there we have it.
A nice, smooth, shiny, semi-satin
finish at the end of the peg.
