The Ultimate TUB Camping Solution

RetroCarz
284 followers
All right, welcome back to episode two, guys,
where you're going to see me not finish this tub off
because there's so much we have to do
before we can finish the tub off.
But in today's episode,
we're going to finish off the headboard,
finish off the rooftop mount,
and then that's it,
because we can't cut flares or make tubs or anything
until our chassis gets here,
and chassis is a dime a dozen.
So let's get into this episode
where we finish off this tub.
All right, so Mickey came and dropped our rooftops off
for us, but this is actually a bit of history on these tubs.
Mickey really wanted it,
and then I full snaked it from him
because he wasn't quick enough.
So what do you think, mate?
Do you still want it?
I'll take it once it's all fixed.
I'll let you fix all the holes up for me,
and then I'll take it.
If you haven't seen Mickey's Instagram,
jump over to Mickey Fair.
He's got a sick GQ,
taking a little bit of inspiration from it.
It's a pretty wild art thing.
Big fanboy over here.
And thanks, Mickey, for dropping off the rooftops, buddy.
No worries.
You little f***ing dude.
All right, so I basically built this whole tub rack
around this.
Now, I won the argument.
Sam didn't get a say.
I got an X10, and it's sick.
So this is the Outback Tourer 1.4 X10.
Now, mostly you get the 1.2
to fit on the top of most dual cabs and stuff.
But because we've got the privilege of having a tub
and sitting it down on the tub,
I can afford to get the 1.4,
which is a lot wider.
Let's unbox it.
We'll get it on the hoist,
and we'll chuck it on the back of the GQ
so we can kind of see
if the headboard's going to work.
That might have to change.
Ah, see?
X10, very good.
I'll show you why I chose X10.
These are my favourite things on the market.
So, usual tent.
Up like that.
Not this one.
Has this extra room at the bottom.
Now, it may not look like it's a lot of room,
but trust me, once you're in there,
it makes a drastic difference.
You can...
And then, hold on, it's...
Wait, we're not done.
Okay.
There's more than meets the eye with this tent.
So, your usual tent finishes there
and has your rain fly.
Once again, not this one.
Room out the front as well
for an extra window.
You literally can't go wrong with an X10.
I can't believe Sam tried to get me
to get a usual tent.
It's literally a palace.
And because of the pop down here,
this goes higher than usual as well,
because normally that would be like here.
It's literally just the best thing ever.
A few moments later.
I have something to admit
and it's hard for me to do this
because I'm not...
I'm never wrong,
but I may have been this time.
So, with the X10,
I accounted for the height of the X10.
I did not account for the 13 degrees of slope
on the headboard to match the GQ.
Therefore, the X10 comes up.
It narrowly clears my headboard by a millimetre.
However, not when I make it wider.
So, I have to change it.
We're gonna have to run a regular tent.
So, Sam can set the tent up
and get into the tub at camp.
Everyone was rooting for me,
but I f***ed up.
F*** off, Sam.
Hello.
All right, we're on the road again.
We're heading back to Brisbane for a couple of reasons.
Number one, I feel like I won the...
Well, I didn't win anything, but I was right.
The X10's not gonna work.
So, I think we filmed...
We were about to...
We unboxed the tent.
We're about to put it on.
We did put it on.
I don't know if we got any content.
We got some photos.
I didn't really want to admit the problem,
so I pretended that it never happened.
Look, it worked-ish
and I would have been fine for it to not pop up and lift,
but even having it popped when it was closed,
it would still hit the headboard, yeah.
It was still hitting the headboard even when it was down.
So, it was just not gonna work full stop, which sucks.
So, we are on the way to Outback Tourer
to swap the tent for one of their just standard ones.
It's a little slim line.
It'll just give it a heap more room, so...
It's still a 1.4, though.
Yeah, we've still got on the wide tent.
Still a 1.4.
Also, we've got the car trailer dropping that back,
so we've got to pick up a chassis now.
Bit of research.
A couple of the boys chatting to guys.
We're gonna go with a wagon chassis,
which means it's got the right wheelbase,
the right length of chassis off the back
because it's a really long tub.
So, we're gonna get this.
It's cheap, it's like 500 bucks.
We'll strip it, take it home and make our own tray mount,
so it'll put the tub on the back.
But yeah, it's just a lot easier and a lot cheaper
to find a wagon chassis than it is to find a ute,
but it is coil cab, coil rear end,
and it will just save us a lot of time there.
So, drop off tent, pick up chassis, get back to work.
Does anyone else hate when Google Maps reckons
you take Gympie Arterial Road
and then you hit a thousand lights through Brisbane
and the traffic's always absolutely f***ed
and you get to your destination half an hour later
than you should,
but it's the quickest way when there's tunnels
that take you the whole way through Brisbane?
Because I love that.
I don't know if anyone else does.
I'm sure people in WA could totally relate,
and Melbourne, and anywhere else,
but here, Brisbane traffic.
We say we're, oh, Brisbane traffic,
but you know what's worse?
Sydney and Melbourne.
Nah, you know what's worse?
Perth, bro.
Perth is cool.
Nah.
It's 40 minutes.
So this is what we worked out on our last trip.
Adelaide, everywhere is eight minutes.
It's a full simulation.
You can go from one end of Adelaide
to the other in eight minutes.
Anywhere in Adelaide is eight minutes.
It's weird as f***.
It's Perth, anywhere is 40 minutes.
You want to go get a bite to eat, bro?
The walk to the cafe is 40 minutes,
and the drive would be 40 as well.
Perth is way worse.
Alrighty, so we've got the tent now from Outback Tour.
It's all loaded up,
and we've just pulled up for this chassis.
So it's sitting out here.
There's a bit of weeds around it,
but it's only been sitting outside
for maybe three or four weeks.
So it's the chassis we can use
because it's a wagon.
It means it has the right length,
but we're going to have to obviously cut
all these mounts off
and put on our own ute brackets.
So it'll be pretty easy
because we'll be able to set the two chassis
next to each other
and pretty much match the ute mounts
for this chassis.
So flick off the diffs,
sell all those bits and pieces.
Pretty much the only thing we'll keep
is the rails themselves.
So now the mission is to get it out of here,
get it on the trailer,
and get her home.
So hopefully our winch works on the trailer
because it's been a bit dodgy.
We didn't film getting it on
because it was a bit of a three-man job.
Anyway, ready to hit the road, get home,
start stripping the seat.
So I lost the battle.
Everyone in the comments roasted me,
said that we need practicality.
So I guess we're going with the standard tent.
Now there's nothing wrong with this tent.
It's still a great tent.
I just have a weird connection to X tents.
So we're going to put this on
and test how practical it is
so all you in the comments can shut your mouth.
So we've just thrown this rooftop on
and now it's starting to clear everything,
which is pretty good.
It's perfectly wide enough being the 1.4
and it looks nice and slim sitting on this rack.
Once the rack's black, you won't even see it's there.
So we'll just open it up real quick
and see if it clears as is.
Works like a dream.
All right, so the tent fits
and when it's fully opened,
you can still open it
just like how Sam wanted.
So you can still get into the back
when the tent's open, which is pretty good.
Have to change a little bit out of this frame,
but it's to be expected.
This headboard design's kind of just hurting us at the moment.
I've took the rails off the tent,
which you really shouldn't do.
It voids your warranty.
But I've done that and then bolted it
through the frame directly to the tent
so it sits nice and flush.
And I've also put some little clips in here
so you clip it down while you're driving
and it doesn't go anywhere.
All right, so I've just gone and boxed up
these little sections here
with some small plates I cut out on the plasma cutter.
Now what I'll do is take it off the car,
weld it out, blend it off completely
so it's just like a seamless 25 mil thick headboard.
This is an extremely long and tedious process,
but you just got to trust the process
and hope it looks good when you're finished.
So we're going to rip that off now
and then start welding out,
blend off and should be sweet.
All right, so once I've gone through the grinding process
with a 60 and an 80 grit,
it still leaves some pretty deep scratches
and doesn't really do a nice finish.
So then we'll move on to an orbital sand.
Now we just got this orbital sander from SP.
It's just a pneumatic one
and SP is known for their great quality in air tools
and it definitely shows.
This thing's probably one of the most used tools
in the shed, not gonna lie,
with paint work, fab work.
This thing's caught an absolute beating
and it's still good to go.
But then you just run the orbital down here
with a 36 grit on an orbital
and then you move to a 60 grit
and that kind of gives you like a nice finish.
This is only like a five minute segment for you guys,
but it's been about two days for us.
So let's keep going on this
and get it finished perfect.
Rightio, so as you've seen,
we got the headboard blended off
and we've now put it on the car.
It's just sitting there for like a idea,
but today we're going to start washing
and stripping the GQ coil chassis that we got.
So we've got a bit of work to do on the chassis,
like rust wise, there's absolutely none,
not even under the coil towers,
which is pretty common for GQs,
but it's in really good nick,
just surface rust.
There's a bit of work we've got to do.
We've got to cut out, obviously,
the long arm brackets on the bottom.
We've got to weld on some ute brackets
for the tub
and I noticed the tub has a lot of little spaces
along it as well,
like support beams for the tub along the chassis.
So we're going to have to weld a few of them on as well.
Get ready to do the hydros in the front and rear as well.
So that's, you've got to cut out the bottom
of your shock mount and stuff,
your coil mount, sorry.
So yeah, there's a lot to do today.
So we're going to kick in by washing it first.
Tech tip, when you buy your GQ,
you can see these,
they're really good frisbees
and you never go get them.
They're shit.
They trap all the dirt in.
You can't wash these out.
It's exactly what you do with them when you get them.
My GQ had the same thing.
All problems.
All right, so as we've seen,
we bought a wagon chassis
because ute chassis are impossible to find.
So with the wagon chassis,
obviously you've got different mounts for your tray mount.
So we're just going to cut these off
and then you can get like a ute kit online
to just weld on your own chassis bracing
and ute tray mount.
So we're just going to do that
because we'll probably make our own tray mounts
because it's a lot easier.
But yeah, so you just start by like
cutting these stitch welds
and then just smash them off,
clean the chassis, prep it
and then we'll just make up some tray mounts
to suit this tub.
Hi guys.
Now Mitch did do a little talking segment on this
but his mic wasn't bloody working.
So what we're doing here
is notching out the chassis.
It's required if you're doing a lift
over three or four inches
or if you're creating a suspension setup
with a lot of down travel like we are.
It makes your drive shaft clear.
You also got to flip it
so that the skinny side is up the top as well.
You have no dramas with that.
All right, so we've gone and done that crossmember mount
and knocked all these body mounts off.
Now the next thing we're going to be doing
is working out our tray mounts.
So the first one I've measured from body mount back
to sort out where our first tray mount goes
and the correct height of it.
Now I've noticed that the coil and leaf chassis
has a different height from here to here
but that should be fine.
We'll be able to get away with that
with the tub pretty much sitting flat on here.
So first thing we're going to do
is mount the first two front tray mounts
and obviously I've measured back so that's fine
but then we're going to get a laser level out
and try and laser level them
so the rest of the heights won't be changing.
And after this,
after we've got our tray mounts tacked on
and our long arm front mounts on
we'll be able to get the chassis 3D scan
and we're going to make up
our own chassis bracing as well.
So we're cracking into that.
I've gone and cut these out on the plasma cutter.
I've basically just cut out two side plates,
the backing plate and then key weighed them
so they can just sit together
and makes it a bit easier to weld
and just line everything up.
So we're going to slap them together on the front,
make sure they're perfect straight
and the right heights
then we'll get the laser level out
through the rest of them.
All right now we've got these centered,
tacked up
so we're just going to tack them onto the chassis.
I'm going to tack on every mount.
I'm not going to weld anything out
until we have the cab
and tub on to make sure all the levels are right
but just give these a quick hit onto the chassis
and I'll put the other one on, same thing
and then we'll be able to measure them,
find out where our hole needs to go for the top piece
and then we can laser level,
figure out where the rest go.
All right so that's about all we can do on this for now
because now Sammy and I have to go down to Melbourne
to go to the Keep It Read event.
So stay tuned for that.
That should be coming out next week.
That's going to be a cool one
and then we can get back
and start cracking back into this thing.
