AUTOSAVER88 FRP Hard Tri-Fold Tonneau Cover Review & Install: Chevy Colorado Truck Bed Upgrade!

Coach Helder
39 followers
11 Video Views·Dec 11, 2024
hello and welcome today I want to talk
to you about a new tun no cover that I
picked up for my 2021 Chevy Colorado
pickup truck and I picked up this cover
from Auto saer 88 store on Amazon this
tun no cover is a hard trifold cover
which fits my 5.2t bed on my Chevy
Colorado it is crafted from fiberglass
reinforced polymer and features an
internal honeycomb structure from what I
see this cover is built to last and
could hold up to 450 lb of pressure up
on top I was in the market for a new tun
no cover I had one for about 3 years
that uh has been lasting pretty well
still pretty good to go but I didn't
feel as safe about it because it wasn't
that hard plastic that this one Now
features so for me even any wouldbe
thieves or anything a lot easier to get
into my old one that had the vinyl cover
as opposed to this one that is now much
more beefier and more secure the
installation on this cover was fairly
simple there is a user manual that comes
with it and I just follow the steps I
had a buddy of mine because uh it is a
bit beefy uh heavy to maneuver
especially when I was actually trying to
record some videos so that I could share
it with you so if you do have a buddy
that could give you a hand I highly
suggest that and once again all I did is
go through the steps in this little
handy manual there were no surprises
everything worked quite well and I was
impressed by the construction uh what I
want to do now is just go over a little
bit of the install and what I did to get
this installed and and my hopes is if
you do pick up this cover it'll make it
that much simpler by me sharing this
information with you for you to get up
and running installed and enjoy the
benefits of this to no cover so
initially I had to remove my old cover
once it was removed there was uh some
dust and some dirt there I got some
Windex paper towels clean that up now
that I had everything cleaned it was
time to move on to Step One in the
manual which is to stick the front seal
strip on the front bed rail once I was
done with that step number two was to
place the assembled cover on the
bulkhead against the cab step number
three was to slide the front clamp to
the best position clamp the interface
under the metal bed rail point and then
use the triangle screw which is a wing
nut and rotated it on the metal rod to
fix the entire clamp step number four I
connected the provided rear clamps to
the T Bar on the cover as shown in the
figure which you'll see in the manual
step number five was to fix the rear
clamp on the third cover as shown in the
second cover so you're basically just
repeating the step once more for the
third segment of the cover step number
six is to adjust the connection position
of the rear clamp and T Bar and then
from there you're just going to push the
rear clamp vertically to fix it into the
rails on both sides step number seven
all clamps must be firmly in contact
with the lip of the metal bed rail to
ensure a firm cover step number eight
Slide the front clamp to the best
position clamp the interface under the
metal bed rail point and then use the
triangle screw that is included and
rotate it into the metal rod to fix the
entire clamp all clamps must be firmly
in contact with the lip of the metal bed
to ensure a firm cover fit finally close
the tailgate to complete the
installation step number nine when it's
necessary to completely fold the cover
place the rear clamp correctly into
position by clamping stamping the rubber
block and then folding it and then the
final step that we did was to attach the
Buckle onto the strap fix that into
place so that you can go ahead and click
that in when you need your too cover
open and that was it relatively painless
installation no special tools were
needed as I stated it was good to have
my buddy here to give me a hand made
things a lot easier smoother and faster
and I have to say upgrading to this bed
cover it was a whole other world
compared to the initial one that I had
in installed in my Chevy pickup truck
I'm happy with the construction of it
I'm happy with the look of it so bottom
line if you are in a market for a tun no
cover that is hinged that is made of
high quality polymer that could hold up
to 450 lb and looks great on your truck
definitely take a look at this tuno
cover by autosaver 88
