How Power Inverters Work (Complete Guide to DC to AC Conversion) #documentary #cd4017 #inverter .

Terrific Physics
40 followers
In a home which utilizes a solar energy from a solar panels and has appliances that uses
AC current to power those devices, he needs to convert the DC current from the solar or
battery to an AC current for the AC devices. Therefore, the need of inverters is essential
components to study. In this video, we want to see how an inverter works. Inverter converts DC
current to AC current by switching the direction of a DC current several times per second. For
example, in this circuit, we use the IGFIT to switch the DC current on and off. When one transistor
is off, the other one is on. How? Let's start with simulating the inverter project inside
Pro2 software. We have used several components such as integrated circuit CD4047, which is our
controller. We have two resistors. We have two IGFITs. We have a transformer. We have a capacitor.
We have variable resistor. Others devices in the circuit are the DC voltmeter and AC voltmeter
and also some motor to show the direction of current.
The project shows that the motor connected at the DC source is rotating all through in one
direction, while the motor connected at one end is alternating in direction clockwise and
anticlockwise. Now let's assemble our inverter. The inverter is able to convert the DC current
to AC current with the help of the transistors. Through the signal from the controller terminal 10
and 11, the transistor enables conduction effectively. Now this is how. IGFIT is essentially
a combination of a MOSFET and a BJT. It combines the high input impedance of a MOSFET with the
high current capability of a BJT. The IGFIT here operates similarly to a MOSFET. Applying the
voltage to the gate terminal controls the conductive between the collector and emitter.
When a voltage is applied at the gate terminal, it controls the conductivity between the collector
and emitter. Therefore in this circuit, if we applying the voltage to the gate of one transistor,
it allows conduction. Applying the gate voltage to the other transistor it allows for conduction.
Now the second part of the circuit will experience the alternating current, since when the first
transistor is high and the other transistor is low. When we do this as transistor 1 is high and
transistor 2 is low, then transistor 1 is low and transistor 2 is high, then we will get one complete
cycle of the frequency. We need to do the opening and closing of transistor 1 and 2 60 times
each one second to achieve 60 hertz frequency alternating current. This can be easily done by
a controller which can provide an on and off electrical signal for 60 times per second.
The signal generated is square wave AC wave and has harmonic distortion.
The harmonic distortions can reduce the efficiency of the inverter system due to overheating and
power losses. Therefore concept of the pulse width modulation arises. The pulse width modulation
uses the square wave generated and reduces it to other smaller square wave signals with different
widths. The width of the pulse, sometimes called pulse width offset, is commonly proportional to
the amplitude of the output signal. Important parameters in pulse width signals are the duty
signal and frequency. The duty cycle may be described as the fraction of a second that a
signal has. Also a frequency may be related to the amount of time a signal takes to complete an on
OFF state. Duty cycle can be 50 percent, 75 percent, 25 percent and the rest. When we take a one frequency
and give it a pulse width module, we will get a smooth AC current with no harmonic distortions.
Therefore we need a microcontroller that can provide this pulse width modulation at any
frequency needed. Therefore we can use CD4047. CD4047 has 14 terminal pins. It has the ability
to operate in both astable and monostable mode. It has to be connected to the external resistor
and capacitor, which in astable mode, it operates by charging a capacitor using a variable resistor
that is mainly used to adjust the frequency near 50 hertz. In monostable mode, an external resistor
must be connected between pin 1 and 3 of the IC that helps in determining the output pulse width.
The CD4047 has 14 terminals. One is connected to the external capacitor. Two is connected to the
external resistor. Three is a common pin for establishing a connection with resistor and
capacitor. Four is for astable and must be kept low when used in astable mode. Five is still a
stable and must be kept high when used in astable mode. When I say high, it means state 1 or on state
and when it is low, it means state 0 or OFF state. Terminal 6 is for trigger. That is high to low
transition will be given to this pin when used in monostable mode. Seven is VSS or ground pin.
Eight is positive trigger, low to high transition when in monostable mode. Nine is external reset
trigger when a high pulse is provided to this pin, resetting Q to low and Q bar to high. Ten is Q,
which generates high output. Eleven is Q bar, is the inverse output of pin 10 producing a low output.
Twelve is the retrigger pin. This pin is used in monostable mode for simultaneously
retriggering that is positive retrigger and negative retrigger. Thirteen generates oscillated
output. Fourteen is VDD, which is voltage supply pin and the formula for determine the frequency
of pin 10 and 11 is F is equal to 1 over 8.8 times or times C. For example, I want the frequency to
60 hertz and I have 200 ohm resistor. Using the formula, the required capacitor will be 9.47
microfarads. The generated output is therefore stepped up with a transformer. I hope you found
this video informative. If you did, kindly subscribe, like and share. See you in the next one.
