Shaping a Bottle on the Potters Wheel

The Story of Ceramics and Porcelain
9 followers
Hey guys, this is Keith from Echo Ceramics. I'd like to show you
how to make this cylinder into a bottle
like that. Alright, let's get started. So first thing I want to do is just shape out the
bottom half
and you can use your hands. So a couple of tools that I'll be using
for this demonstration is a wooden rib,
a stainless steel metal rib, and you'll most likely
will need a needle tool. So first thing I want to do is I want to go ahead and just
do the initial shaping
with my hand because the opening is pretty small. It's about three and a half inches
in diameter. I'm going to go ahead and just wet the primary, the interior of the wall
and I like to use the rib as my guide.
I'm going to go ahead and bowl the bottom shape out and the type of bottle that
we'll be making is
sort of the tear shape. So I'm going to go ahead and shape the bottom out like so.
So I'll do that once more. I'll just go ahead and extend the bottom out a little more
and smoothing it out, compressing at the same time,
just curving the metal rib like so.
At this point I'm going to go ahead and switch to my wooden rib.
I'm going to go ahead and make sure it's clean,
especially the blade side down. I'm going to go ahead and use my left hand.
I'm going to hold the rib pointing side down and go ahead and just
lean with the rib and using the maximum amount of contact
to give that nice even bulge.
The shape I'm looking for here is sort of a
more or less like an egg shape. In this case it's particularly a round one
but I'm perfectly content with the bottom half of the shape
so we'll talk about coloring the top half in now.
So I'm going to soften up the shoulder so I don't have a
sharp right angle because that can become a
weak spot. So at this point I'm going to close off. I'm going to go ahead and remove any excess water
that I might have put in. So I'm going to go ahead and just take out
the water. You might have to do this multiple times.
Now one thing I'm going to avoid is putting any excess water
on the inside of the bottle that I'm making.
The reason being is that if you put any water in, it's really difficult to get that out.
Some people use sponge and a stick which you can. To color
and I often like to use the word choke
because it's a lot like choking a person. What you want to do is you want to wrap your hands around
like on a person, around their neck and you want to go ahead and squeeze so that
you're actually sort of squeezing the air out or choking the person.
So one thing you want to do is press down on the shoulder
because you're not really choking the clay
or anyone else for that matter. And the other thing that's really important when you're
coloring or choking is that you want the opening to be the smallest.
In this case I'm going to make a bottle like this one here. I want to go ahead and make sure the
opening is the smallest.
So I'm going to wrap my hands around, all the way around
to choke. And you can do this multiple times
not being too aggressive. Each time I do it I'm going to lubricate
the top half but not the bottom half because I'm not physically touching
the bottom half. So the important thing is not to
unnecessarily wet the clay where you're not going to physically touch with your flesh.
Alright, at this point it's getting a little compressed and condensed
meaning that the wall is getting a little thicker. So I'm going to go ahead and do a light pull.
I'm going to go ahead and use my inside finger and I haven't added any
water to the interior because it's unnecessary. Even if it's a little dry
the amount of contact I'm making is pretty minimal. So I'm going to go ahead and do a light pull
and you can see nice even parallel lines.
And the other thing to keep in mind here at this point is
not to leave the rim thick. So if your rim feels a little thicker than the rest
I would go ahead and highly recommend thinning it down. So I'm going to go ahead and
do the claw. Often this refers to claw, right? I'm going to go ahead and just give it a
light little pinch without torquing. If you pinch too hard you're going to torque.
There you go. Thinning that down a little. I'm going to go back to coloring or choking if you will.
So the important thing here is not to have a flat area, right? So when you
choke, you want to wrap your hands around, squeeze, keeping your thumbs up. As you come up
make sure the opening, looking at the opening and making it smaller visually
and your hands will do the work for you. Like so. The other thing that I really like to use is my
thumbnail. My thumbnail as sort of as a miniature rib because you could use a
rib like this and do a pretty good job and which I do often but one of the
things that I find a disadvantage of using a rib versus my thumb is that I don't
really have a good sense. I don't really feel the clay when I'm doing this. I can't
really be as aggressive as I like to be and if I'm being too aggressive at least I'll know
because I could get a better sense of my fingers. So for the most part I like to really try to use my
hands as much as I can. So I'm going to wet it evenly. I'm going to use my thumbnail. Again I'm using the
blade of it, right? I'm not using the fatty part of the thumb. I'm putting my
thumbnail right against the clay, pressing in whatever you can. Try to make your hand
trouble where the top is going to start to ripple. I don't want that ripple effect so I'm going to go ahead and color that in. So I'm going to wet it down with my
sponge with some water. I'm going to make that opening a lot smaller like this, right? If you
get a little bit of rippling, ease off a little and go ahead and rip to straighten it out. Otherwise you
want to keep coloring. At this point I'm almost using what's often referred to as a four point.
If you do a four point, you want to be four equal distance, right? This wouldn't be a four point or
this would be a four point. You want to make sure it's four equal distance at all time as you color
and hold and release slowly. Alright so I'm going to make my opening fairly small. So I'm going to
go back just below the bump here, even that out a little. I'm going to go ahead and color up a little
more. So essentially I'm shaping and pulling at the same time. Having a bit of a clay like this
is perfectly normal. So I'm going to go ahead and thin that down a little. Now if you get a ripple
and or if you have an uneven part of the clay, you could perfectly just go ahead and
cut that part off. So like here, I don't want to cut too much because I worked too hard to
get this height. I don't want to lose the height but you just want to cut just enough so that you
could take it off in one ring, right? Insert the needle slowly, just take that piece off.
Whenever you cut, you should always sponge it and soften it up. The main reason for that is you can't
tear, right? So I'm just about there. At this point, it's all about fine-tuning. So I'm going to go ahead
and do often for just a six point. In this case, it's more like five points with a sponge. So you
can do multiple different points if you will. All right. So I'm going to keep working on the neck
because the neck is the last thing you do. So if I wanted a flare top, I would actually have the
flare at this point and then work on making the neck. So the thing to keep in mind about
bottles shaped like this, one, you don't want to be too aggressive but the other thing that I really
want to talk about is the neck itself. If you make the neck opening at the narrowest part is at the
top, it doesn't tend to look very good. So the idea here is that you want to make the opening a little
narrow at the bottom and then have a slight flare. And if you happen to have some little bumps and
so on, you can take care of that in trimming. So if you don't know how to make a cylinder at this
point, you should go back and watch my video on making cylinders. Once you have a cylinder, that
will give you a lot more options. All right. I'm going to go back to four points with a sponge.
I'm going to narrow up the bottom a little bit. Following up at this point, I'm just
gently following to keep this more or less straight. Now of course, this becomes a very
delicate area. So a couple of things I want to do is I want to smooth out the neck.
And even if it isn't perfect at this stage, you could make that so much better in trimming stage.
So don't sweat over little things, right? So I'm going to give a little flare at the top.
I have a little bump there, which I could trim out a little later, but I'm going to try to see
if I can resolve that a little bit now. All right. All in all, I think I'm okay with the opening.
I'm going to go ahead and sponge lightly, still keeping it centered. And I'm going to trim anything
that bugs me at the trimming stage when it's leather art. All right. Take a lean back,
take a little look, a little fine tuning here and there. I don't want to take up too much
time here. And then last thing I could do is give it a little final shaping. So I could remove some
of the excess water that I might have dripped. And that's important because I don't want the
plate to absorb any excess water because it's going to dry unevenly. So I'll just go ahead and
smooth that down. Now let's use the rib on the flip side of it. So I could use that to make the
almost like an S curve instead of digging in the corners of it. So I could use this part. And again,
if I have a little bump there, I could always trim that out. But don't think that you have to do
everything at this stage, right? Drawing is only one half of the work.
Other half is all in trimming. You could fine tune so many things. I don't trim much clay,
but I'm a big fan of trimming. So I'm going to be trimming this from top to bottom,
making sure there's any little bit that I don't like is removed. So you have to be careful not
to shape too much because then you can see the top here start to wobble. And if it starts to
wobble, clay is kind of telling you, you know, you're pushing a bit much. So I'll go ahead and
leave this part for now. And then I'll take care of it in trimming video. So if you make a bottle,
watch my trimming video of the bottle. I'm going to go ahead and re-center this by just starting
at the bottom. And you'll start to see that it wobbles a little more. But if you use your sponge
and your fingers to guide it through, you can just simply hold and just let it get back in line
because it used to be center and the clay wants to go back the way it used to be.
Just like that, right? Light guidance. All right. All right. I'll leave it at this stage
and we'll take care of the rest of it in trimming. Thanks for watching.
