Making a Leather Sheath: Full tutorial

Native American Crafts
28 followers
6 Video Views·Dec 8, 2024
In this video I show the full process on creating a leather sheath from the beginning to end for the Hunting Knife project. Details are provided on carving a leaf motif and coloration using an airbrush. Additional tips are provided in certain areas on some of the processes used along with specs on tools, and dyes.
In today's video we're making this. Welcome to the channel. In today's video we're going
to make a sheath for this hunting knife that we just recently finished. Now the customer of this
knife recently showed me a picture of a sheath I had produced a while back. They want something
similar in design but they want to twist, they want to add a whitetail skull or a whitetail
deer head. So we'll have to see if I can fit that into the mix with this sheath design.
Overall considering this blade profile is very narrow which could make it tough to create an
intricate carving for the sheath. So let's head to the leather station and get tooled up. The
sheath we're going to be making is a pancake style with a Mexican belt loop, possibly two loops.
So first things first I gotta go ahead and create the design. So I'm going to sketch out and rule
out the sheath design and I'll put in the notes some of the measurements on why I'm making some
of those measurements on the sheath. I prefer to grab my outlines directly from the blade itself
because I find a finished blade usually varies from the original template. What I'm doing here
is trying to determine the best straight angle for the inside of the well of the sheath that
will clear the belly and recurve on the blade. What you don't want is a bottleneck at the throat
of the sheath that is too snug or even stops the blade from insertion. Okay we traced out our
pattern front and back using a red gel pen for the mark out. If you're not familiar as to why the
color red is used it's because the majority of leather dyes consist of a red orange base and it
makes it easier to blend in and hide the mark up or any wandering lines when you go ahead and
dye the leather. Now before we trim out our sides I like to make an initial cut with a swivel knife
and that helps guide the blade during the trimming process because
nobody likes squarely cuts right. So you probably noticed the blade on this swivel knife is quite
small. I've actually made this out on the lathe and modified it to make very intricate cuts for
small carving patterns but it works so well that I use it throughout the carving process.
So let me hone the edge on the blade and we'll get started trimming this out.
With the sides of our sheaths cut out we're going to move on to laying out our stitch lines. So I got
a stitch grooving tool here. We're going to mark out down near the tip and I'll show you how to do
that. Instead of pulling on a cut we're going to go the opposite way on the blunt edge. What that
helps us do we're going to put a couple marks in here and it's going to show us when we start our
groove where we come down to it's going to show us where to stop. That way we don't pull too far
ahead of the other line as we come down the other edge. After cutting the stitch lines I come back
with another cutter set at three-eighths of an inch and using the same process I begin setting
my picture frame for the carving. At this point I decided to change direction with the deer skull
concept. Given the small width of this particular sheath it would be a real challenge to carve any
decent amount of detail like I did on this quiver for example. Here I begin making undercuts to the
leaves and other areas of the pattern. I find a step to be the key detail towards giving any carving
even those with the most basic design elements a 3D look. Most of my undercuts stem from the use
of the D60 and D892 bevelers and a custom tool that I made from an old screwdriver which is
sharpened. This tool is used like a razor to get under the top grain of the leather and instead of
pushing the undercut is lifted up. Okay so you probably noticed that I went ahead and tooled
up a belt loop. Same process as I've shown thus far so I didn't feel there was a need or any
benefit to showing the details of it. At this point I've decided to skip on creating a Mexican
belt loop and go for a frog with a bullet keeper as I didn't feel like the latter went very well
with this sheath. The main reason for this change is because I want to keep the emphasis on the
carving. So my apology to those who are watching for that style sheath however I promise to do a
Mexican belt loop build in a future video. So before I begin mock-up of the keeper strap I
need to head out to the shop and melt some copper to turn on a lathe for the bullet. Yeah so I had
this great little cinematic clip of me melting copper in the furnace and making some round bar
in a mold. Of course I forgot to record the apex of the clip which was the pour. Out of all
areas I could have missed recording I missed the pour. So now we'll just jump ahead to the lathe
and get this piece machined down so I can get back to making the frog. And that is how you make a
custom bullet for a frog. Now what I need to do is get this centered up and hole punch for the screw
that holds the bullet in place. I'm using a scrap piece of leather as a backing for the punch to
give it a clean cut through. And since the screw has a beveled head I'll need to go ahead and
countersink the back side of the hole using a French edge skiver to create a flush fit. Normally
I stitch and pull a liner over the top of the sheath but the odd shape that I created to fit
the knife guard won't allow for a clean finish. So what I'll need to do prior to stitching up the
sheath is skive a thin piece of leather and glue it over the screw head so it won't scratch the
knife blade. After I check the fit on the sheath I can begin moving forward mocking up the template
for the keeper strap. I'll go ahead and show the template build but skip the tooling process as
it's identical to what's already been shown in previous steps of the build. Here I begin prepping
the welt or glue up to the back side of the sheath. All I'm doing is hitting the top grain with some
60 grit sandpaper to help with adhesion. Then I'll mark out where to place the barge with cement
so it doesn't creep out past the welt and come in contact with the knife blade.
So to get a rough measurement for the keeper strap on the Krog I'm taking a piece of scrap
about the same thickness as the sheath material and wrapping it around the sheath layers to mark
out the center and ends, making sure to leave enough material for adjustment later on.
As I mentioned earlier I'm not going to head into much detail on tooling the keeper strap
I'll just highlight a few segments of the rough process for interest.
Before heading into coloring the sheath I prefer to use a wheel spacer to mark out my stitch holes
because it's easier to see at this stage. Spacing for the sheath is set at eight holes per inch.
Once finished I'll begin prepping a Pasche DL airbrush to spray Feelings alcohol-based dyes.
I prefer these dyes over water-based and other dyes because of the great coverage and they dry
uniformly. It's the next day and the resist has set so now we can begin working on applying the
antique to bring out all the hidden textures and details. For this project I'll be using EcoFlow
jelly antique. It's in a dark brown color. It's a water-based antique and I find it easier to
manipulate or clean up with a bit of water. When working with this antique I like to apply it with
a brush into small sections to get into all the details and undercuts and wipe it off immediately
to avoid staining any highlights on the piece. Once the antiquing is finished I'll let it set
for a couple hours before sealing it up again with the Resolene. Alright the antiquing is finished
and another coating of Resolene has been applied to seal it up. I went ahead and coated the back
side of the leather with moccasin brown prior to stitching. In the next few clips we'll install
the bullet, stitch up the sheath, round off and burnish the edges. Though I should point out the
top of the sheath and components of the frog need to have their edges finished prior to any assembly.
With the sheath sides glued and aligned with the help of a few makeshift pins
we can begin measuring out the length of thread needed to stitch up the sheath.
What you want to do is take the parameter of your stitch line and multiply it by six lengths. I find
this gives me plenty of thread to finish two sides plus the wealth of eight to nine ounce leather.
Thinner or thicker leather or even a shimmed wealth will require you to add or even subtract
the length. Regardless it's better to add to your overall length of thread to avoid coming up short
a few stitches from the end. When working on knife sheets I prefer a heavy wax thread as it's more
impervious to elements and is a lot less easier to break over time. It also allows me to do a
standard saddle stitch without having to wrap a knot on each pass. However I do like the back
stitch and overlap at each end to lock into stitching. After evening up the sides on the
belt grinder using a 220 grit belt and beveling the edges with a size 4 beveler I can begin
polishing. A key tip towards smoothing the grain is to just moisten the leather not soak it. Too
wet and the grain won't mold smooth and you'll just push it around causing the edges to crack
or ball up. Multiple tools can be used to buff the edge but my personal favorites are this wooden
slicker and a piece of old blue jean. Once I've gone over the edge with an initial pass of the
slicker I hit everything back with 220 grit paper. This extra step removes any imperfections
and really helps create a smooth finish. Then it's back to slicking up the sides before adding the dye
and buffing to a high polish.
So
well that's a wrap. What you just watched was several days worth of work cut into 40 minutes
of video. Though I tried to cover as much of the build and processes as possible some aspects were
not shown due to repetition. Overall I really enjoyed this build and have an ability to show
you some of my techniques on sheath making. So if you enjoyed this video and learned something from
it then please hit that subscribe button now and like this video. Be sure to leave a comment as to
what you liked or didn't like and also let me know what you'd like to see in upcoming future build
videos. I'll see you on the next one. Thanks for watching.
