Easy Key Fob Battery Replacement for Dodge/Chrysler/Jeep/RAM - Step by Step Guide
Description: Learn how to quickly and safely replace the battery in your Dodge, Chrysler, Jeep, or RAM key fob with this easy-to-follow video guide. Perfect for DIY enthusiasts and car owners looking to save time and money. Avoid dealership visits with these simple steps. Don't forget to like, share, and subscribe for more handy automotive tutorials!
Remove Keychain & Physical Key: Start by removing any keychain attached to the fob. Release the physical key by pressing the latch.
Opening the Key Fob: Avoid using the physical key to pry open the fob as it may release a crucial spring inside. Instead, locate the small notch next to where the key comes out.
Using a Coin for Leverage: Insert a coin into the notch and gently twist to pry the fob open, starting from one side.
Handling the Internal Spring: Once opened, be cautious of the small spring mechanism. It's vital to ensure it stays in place to avoid any loss or damage.
Removing the Old Battery: Identify the CR2032 battery and observe the tabs holding it in place. Gently push the battery up past these tabs, as the opposite side is spring-loaded.
Installing the New Battery: Place the new CR2032 battery under the tabs, ensuring it's properly seated. Be mindful of not leaving fingerprints on the battery or inside the fob.
Reassembling the Key Fob: Reattach the rubber boot and carefully align both halves of the fob. Press firmly until it snaps shut, ensuring a secure seal.
Final Steps: Reinsert the physical key and ensure the fob is fully intact and operational.
🛠️ Pro Tip: Handle the internal components with care to avoid any damage or displacement.
👍 Like & Subscribe: Enjoyed this video? Give it a thumbs up and subscribe to our channel for more practical car maintenance guides and automotive tips.
First thing you have to do is just make sure your keychain is off right here.
Take out the physical key by pressing this latch over and some people basically use this key
to pry up on it and you could do that. The only problem you just have to hold on that side and
pull up on this. The only problem with that, I'll show you in a second, there's a little spring in
here that it kind of puts pressure on and sometimes it releases that spring. So another way to do it
is to use a coin and you can see this little space right here. Not the place where the key comes out
but right next to it like so. You put the coin in there, twist it, twist and turn it and pry up and
unsnap it from this side basically. So now it's kind of separated on this side. So now we can
kind of pull it. Now a little spring is in here and I'll show you where it's at. It's right there
and you see it's already half kind of popped up. So you want to be careful you don't lose that
little spring mechanism. So we're going to gently set that down and on this side is where the battery
is located and there's a rubber boot. Just take the boot off like so. Get that out of the way.
It is a CR302, uh CR2032, sorry, battery and you see these little tabs here and here.
You pry opposite of that. You're not actually prying as much as you're pushing. So you see
these little tabs right here on this side. We're just pushing it up past those little tabs because
this side is kind of spring-loaded. So you want to push it up like so. Now it will pop out so I'm
going to just put my finger there to make sure it doesn't pop out and it pops out anyway. So um so
yeah try not to get too many fingerprints on this battery and then don't touch in there basically
because it is kind of spring-loaded and you don't want to get any any dirt or anything in there.
Okay so the new battery you just put it like that and then it's like I said it's spring-loaded on
this side. So you want to push in and compress those springs and make sure you're under those
little tabs there. Push in and then push down like so. So now we're underneath these tabs
here and here. We're underneath those tabs so we're completely down and seated
uh properly. So if you happen to put some fingerprints on it on this side it's not
really a big deal. It's more so the other side. Okay so put the rubber boot back on.
Kind of set it there. Push it in place. You can kind of feel it that it's down in place like so.
Now just make sure your little spring mechanism hasn't popped away and lost it
and just kind of gently put it together like so and press it
until it snaps and make sure it's sealed all the way up around the edges there all the way around
and then you can put your physical key back in and then you're finished.