I Bought a Lemon Buyback BMW X6M and got 50% off because of a Mystery Electrical Issue

Ex Used Car
15 followers
All right, so this is really weird the car is running
That's flickering notice. It's flickering. Look it's in drive
And watch car's moving. Oh, there's no power steering. So we're gonna take it slow. We're gonna go home
And we'll charge the battery up and retest it in a minute, but it feels it's driving real smooth
Look, so we're driving right now. Look
It says we're going zero miles an hour
This is still flickering. Look we're driving
I gotta make a turn here. I flip my turn signal on. I don't even know if it's on
I think when the other drivers see that i'm driving a bmw, they'll understand
Well, I guess the turn signals do work. But uh, i'm pretty sure that fan's not supposed to be that loud
Look at this
This just popped up out of the middle of nowhere. I even pulled the key out of the ignition at this point
Um stuff's still lit up stuff's going crazy
I think that the batteries in the trunk like most bmws
But am I just really stupid or is this car not well thought out at all?
Where in the heck is the trunk button usually on a bmw?
trunk buttons like
Here maybe or or down here somewhere
Look, no center console trunk button. I press this this isn't responding to anything. I'm holding this
Not doing anything. Look
um
Trunk button. How the heck do you open this? There's got to be look what the heck this is like a possessed
bmw and
Something crazy is going on. Basically what I want to do. I'm gonna get to that battery
I'm gonna pull it out. I want to test it
So we know what in the heck is going on here. Jeez
Things are already starting to look like a real winner here. Look at this
That is a nice quality
That's definitely aftermarket with that cheesy clown coloring there, but it does have the m engine what is going on here
Also has some really cheesy, uh oil cap this does look all pretty clean under here. Um, oh what is this?
Just cracked off
Just chilling. What the heck is going on with this car? I've never seen anything like that
Let's pull this off
What the hell look at that
Just pop the oil cap off
10 years ago
The bmw x6m was the fastest suv you could buy even faster than the more expensive porsche cayenne turbo
Today, it's quite possibly one of the fastest ways to go bankrupt
This luxury utility hot rod has the same twin turbo setup as an m5
Which makes it just as unreliable as an m5, but we don't buy decade-old bmws because of their reliability
We buy them for their monte carlo blue metallic paint with this orangish red leather interior
This car is wild and has an even wilder history
It was bought back by bmw with 90 000 miles on the odometer
Which makes little sense while also making it a genuine lemon title car and shortly after it was repossessed
Then it surfaced at auction where I picked up for nearly 90 off its original msrp
Clearly that discount was for a good reason. This strange electrical issue has made this car basically unusable
Even though I drove it a mere mile home from its drop-off
It did so without power steering a suspension that feels as stiff as a rock and clearly without most of its electrical aids
I've worked through a multitude of mechanical and even electrical issues on bmws in the past
But i've never seen one with problems quite like this
I personally love almost everything about this bmw the looks this size
It's drivetrain and I was extremely excited to scoop this m car up for just a little over 12 grand
But it will definitely be a true auction gamble
We could literally have a weak battery or just one bad ground wire like on my old e46 m3
Which also caused a slew of electrical issues or this thing could just be a disaster lemon
That's worth only what it contains in working parts
And in just a moment
We'll start digging into things to find out whether i'll be riding dirty cheap or if i'll be waiting outside the bmw parts department
On black friday, we all know they won't be having any good deals there
but that's okay because i've already got all my gift shopping done since simply safe is offering their best deals of the year and
Giving early access to my subscribers during their black friday sale right now
You can save 50 or more on their award-winning home security systems when you visit simply safe.com
Sam crack simply safe on i've been using simply safe for over two years now
And they're always improving my system with over the air hardware updates and app updates which future proofs the system
It makes it as secure as possible. They're always innovating with new devices
I love my smart locks which can be open with the tap of a button on my smartphone from anywhere in the world
And their brand new outdoor wireless camera
It installs in just a few minutes and has a battery that lasts between three and six months on a single charge
And when you click the link in the description or visit simply safe.com
Sam crack not only are you going to get at least 50 off a simply safe home security system
You're going to own your very own security system. There's no renting or leasing equipment and there's absolutely
No contracts with simply safe. It's a tremendous value because home monitoring starts at just 50 cents a day
I highly recommend it and again, that's at simply safe.com
Sam crack and I got to give them a huge. Thanks for keeping my place safe and for also sponsoring this video. What are those?
Those are one of the first things I noticed whenever I saw the listing for this car clearly someone ripped the nice
X6 m wheels off that these look like more of a basic x5 or x6 wheel but either way
That's not our major concern here. Our major concern is the electrical system, you know, the car sat at auction a while
So first things first
We got to get the trunk open. I did find that trunk unlock button in the car
All right. See everything is just super finicky right now
I've got my electrical system tester there which we're going to use in just a few seconds
First thing I noticed when I checked out the battery is that it has a date of 5 21 on it
And the tow truck driver did start this car right up
So the chances that this battery is bad is uh, very slim at this point
But be easy enough to tell this is an awt tool
Like I said an electrical system tester has a bunch of different functions on it
But we're going to start really simple and just do a voltage test
All you've got to do is like when a set of jumper cables positive to the positive terminal negative
And it should power right up
So we go to this first smart function here
You can see it tells us there is 12 to 12.1 volts coming off of our battery
That is good that will start this car that should be enough to run all the electronics
But it's not just the battery we're concerned about a faulty alternator could also cause a slew of electrical issues
So let's go ahead and fire the car up
And we should see that number jump
And you're seeing a jump right here. Look
So we're averaging well over 14 volts and it's consistently over 14 volts
It's not jumping in and out. So our alternator is likely also just fine
I think we can confidently say the issue isn't with the alternator nor the battery
Plus we've got that electrical system warning popping up on the iDrive
So the car's trying to tell us something we still want to keep things relatively simple here
So the next step for me was to do a quick code scan when I got back the initial health report
There were dozens and dozens of codes across several different modules. Most of the modules contained in the car
I cleared those I re-scanned and a lot of those codes came back
Which unfortunately still doesn't give us very clear direction where to point to so we have an issue like this where there are codes
Just thrown everywhere and they're not very particular codes
You'll notice that each code definition here doesn't really point to anything in particular
You got to look for consistencies
So there's two major consistencies I can point out number one
The majority of the codes seem to be stored in what was called the jbe or the junction box electronics
We'll get back to that in a second
But the second consistency was the fact that a lot of these codes in the code definition said
Kcan in them and what kcan refers to is the can or can bus system
Which is the network of modules communicating with each other to work now putting those two things together
The junction box electronics and a kcan fault and considering that the junction box
Electronics runs a lot of the systems that are on this can network
well
Maybe there's an error here
so I think the next step is to go pull out the junction box electronics is really simple to get to
See if it changes any of our symptoms. I'll try this again
No matter how many times I go and try and shut this car off just you know, normally using the key
It keeps on certain
Electrical functions so you can see lights flickering on and off you could hear the iDrive
Binging and bonging and so now we've got no power to the car and that's also a smart idea
When we go and remove this footwell junction box module, which should be simply located right underneath here
and uh, okay what I don't like to see is
Somebody's messed with this
missing screw screw screw
Let's get in there. Let's look let's hope
Somebody didn't already do this because if they did and it didn't fix our problem
Then we really got to figure something else out and we don't want to do that
So i'm curious to see if there's any water intrusion in this car
I mean water that would get up to the module behind this dashboard
uh would be
I mean monumental
And you'd see a lot of sediment in places like here. This looks all very normal. I don't see anything
super obvious
and
Right underneath here is exactly what we're trying to get to this junction box
All right. So right underneath here. We need to remove a few more things and then we can pop the entire
Uh assembly down and pull the module itself out
All right
one good thing i'm seeing right now, which I didn't think I was going to see is that
There's like this piece of trim that's holding a wiring harness in place
It specifically mentions it in the workshop manual says to remove this piece and then slack in the wiring harness
If somebody really sloppy just came in here and worked on it
Well, I can tell you right now to get this all back the way it goes is not a lot of fun
So the fact that they did this the appropriate way
um
Or didn't do it at all is good. It means somebody probably hasn't replaced this module yet
All right, and look here this comes down
And there is the module right here this guy
That's what we want to try and pull out. I think I can wiggle this out of place a little bit
So i'm going to put the camera down try and get this out
That way I can also inspect the fuses in the junction box here and just make sure it doesn't look waterlogged or anything
Yeah, the workshop manual always makes everything look easier. So
You see there's one tiny little screw you got to get to back there and I thought I should be able to since I slackened
Um the wiring harness back here. I thought i'd be able to just pull this out a bit more to gain access to it
It's no big deal. I've got this really nice small allen head torx
Tool, so that'll get back there. No problem, but i'm going to do that
I'm going to pull this module up and out first and foremost and then
You know one of the things again, we might be worried about is some water intrusion
But if you take a close look and i've got the light on here so you can see
There was water intrusion in here. It'd be a disaster. See it's a little dirty
That's you know, probably pretty normal if you consider that the hvac system is circulating
And i'm moving in particles the the filter for the hvac system is right to the side here
um, so
After 10 years 100 000 miles, I think that sort of let's call it wear looks pretty normal
So let me go ahead and reach my hand back here. I'm gonna grab this module out right now
The module is out. We did solve one mini mystery here
well
the reason that that lower panel there the cover panel for the bottom of the dashboard was out is
what I said earlier, there's an air filter element in there, but
The other reason why i'm darn near positive. This is the original first of all
If somebody took this out and put it back in there's no way they put this
Final screw and it is so difficult to get to it probably took me 25 minutes just for the one screw
And the second reason is the more factual one right here. You see this 13 10 10
I'm sure this has to do with the build date of the module itself
This car is a 2011 which means a lot of parts would have been manufactured on 2010 as well as potentially the car
Now one of the ways we could test this module is without the module at all here
Let me explain it's something I read on the internet something i've never tried before
But I am very excited to try right now because it's literally going to take a few seconds
And it kind of makes sense if you look at these european cars and really any modern car
There are usually dozens of modules in there
Modules that run things as simple as just the automatic door closer
So that module is located underneath here and it's one that it frequently gets taken out by water intrusion in this generation x6 and x5
Uh, there's modules over here. There's one on the floor
Down there and again, they're scattered underneath the carpets and the dashboard pretty much everywhere in this car
Remember, we just removed the junction box control module when we did I unhooked the battery
Well, I just went and temporarily hooked the battery back up in theory a lot of these modules communicate with each other
So that junction box module is responsible for a lot of functions of this car
And remember a lot of our functions were either inoperable or acting very funny
So if that module is gone, let's say a disease module, which is sitting right here
And not hooked up to the car. You can see all the wiring harnesses are still dangling down there
The car is just going to be missing all of those features that this is responsible for. However
Everything shouldn't be spazzing out anymore
The car should kind of work at least certain functions of the car now the car might not even start up
But as you notice when we got in it, there was a light on the dashboard. It wasn't flickering
So, let's see what happens when I take the key
We'll put it in
here
Everything comes on
So far so good. We don't see any flickering of any of these lights foot on the brake
And so the car didn't start up, but look at this. We've got all our information
It's telling us we're low on gas
um
Yeah, I mean nothing is flickering that's a good sign because this thing would start flickering within seconds of turning it on now
Sometimes it would stay solid like this for 10 20 seconds
But it would always flicker before when our junction box module here was plugged in now. Let me try and hit this again
So the car actually will start
Notice our tachometer still isn't running
Our iDrive, let's see here. I'm assuming is not running
Nope iDrive is dead. It looks like climate control. There's nothing coming out of the vents
Yeah, nothing here is running
This is flashing a ton of lights probably again because this module here is responsible for some of these functions
We see here, but notice nothing is flickering
Oh look
huh
A few days ago when we pulled that junction box electronics from the BMW
I think I said that we could test to see if it was bad by pulling out of the car and running it and
well
initially, I thought okay things are better because well the screen wasn't flickering and the dashboard wasn't flickering but
Really nothing worked at all and that's because this module is responsible
For so many of those functions now, this is not the one that came out of the car
I just got this in the mail. I ordered it off the internet from a parts breaker. It's from a high trim x5
It's the same part number, but you can see the build date is different. So this is a spare module and basically
Even though this came from a different car that might have different options from our x6m
It should bring back a lot of the other functions like iDrive and whatnot
So we're going to go ahead and swap this module in place
And if it changes the way the car works and it brings back all electronics online that we know our fault
with the old junction box module
Key, we'll put it in the ignition
Okay, see this
Okay. Well, we've got our functions back, but we've got them back with all the problems
So clearly our issue wasn't with the junction box electronics after all
Let me just take it for a little drive around here and see if it does anything different
And we've got a strong battery. So the car should crank over pretty good
So you see flickering there I hear a lot of clicking coming from the back as well
I wonder if it's this relay right here. It's it's very warm
Let's put in a drive see if it moves. All right now it's moving on us again
And again, it feels like my power steering is like completely gone. Very very stiff
abnormal for a bmw
See sometimes it gives me trouble in reverse right now. It seems to be working
All right
Put in a drive it's working
Oh
Oh, oh
Did you just hear that
It's throwing itself in the park
Randomly, so I got to stop driving it. You can see the gauges are all going crazy
Even though swapping that module didn't really change the symptoms much
I'm interested to see what in the heck is going on with this. Well, check that out
That's interesting
I wonder what all that stuff is. I mean
Doesn't look like uh, it was wet or anything. Maybe it's from all the heat
It's developed some of that I don't even know what you'd call that it's like, uh
The corrosion almost but I mean there's no water anywhere in this area. There's no water down there
Um, this is a common place in the x5 and the x6m to get wet
And i've already checked all down here because that would obviously create an issue obviously where the battery is all good there
so
Well, we need to we need to figure this out
As you could tell car electrical systems aren't my strong suit and every time we fire this crop we get new symptoms
which points me in a different direction and at one point I just
Will start going in circles, which is what we've already started doing the fact that I bought that spare junction box electronics
Not knowing any better not seeing anything obvious
Well, that's basically 80 bucks down the tubes and if I start replacing every single module that's throwing an error code
Well, it's going to get really expensive really quick
So just kind of put everything on hold did my research away from the car
And I remember this amazing youtube channel hosted by a guy named super mario
The channel super mario diagnostics and he's an electrical guru when it comes to these cars
It seems a lot of bmws come through his shop recently an x5 with a similar engine came in his shop
And it had a misfire now bmw guys think misfire. Well, it's easy
It's probably a coil pack or maybe an injector
But it was nothing mechanical and it came down to the circuit board and he very clearly and concisely walked through step by step
How he diagnosed it as an electrical issue instead of a mechanical issue
And so I figured he'd be the right guy to give me some guidance on this
I reached out to him and he cut me nearly a 20 minute video on our issue with the x6m
And how he would approach it here. Let me show you a snippet from the video. Hey there sam. Thanks for reaching out to me. I uh
I'm, i'm glad we could uh collaborate on this one. Hopefully we could get this one fixed
uh remotely, but if if need be we'll go ahead and uh
Take care of it over here at the shop
but
Taking a look at your x6
Uh that video that you sent me
Showing those that relay clicking. It sounds like multiple relays
Um, it was in the rear electronics box. I want to find out what those relays are
so for that I look look at diagrams, let's go ahead and uh,
take a look at
power and ground distribution
and usually
these uh diagrams start out with
All the stuff that's in the front
In the first few pages and then works our way
To the back so and if we keep going
I see a terminal 15 relay
And a bistable relay over here
And I believe that is the one that is outside the rest that bistable relay. That is a current
cutoff
Relay and
You can see right here that
It has a solid ground and the other side of the control is powered by the junction box, which you changed
Let's see if we could just take a look at at its purpose, right?
So what I like to do is use the search function. See if we get lucky put cut off in there
um
terminal control
Terminal control would probably be where we're looking for
So this is telling us
Uh each and every single possible terminal control there's terminal 30 15
let's see if we see cut off in here because
All right. Here it is closed circuit current cutoff relay deactivation in the event of a fault
uh, so
The junction box or the jbe that you changed already and that we need to code
It is responsible for that that cutoff relay so something's going on the junction box is seeing
Some kind of a fault and causing this problem
And we can see that part of that cutoff relay. These are the things that are
Being cut off. We got the trailer module the amplifier the comfort access system
The communication computer the car information computer the multimedia platform the comm box navigation
the interface module
that's that's for a electronic vehicle the instrument panel, so
It looks like all this is leading back to your junction box, which you know, you're already in the right area
Uh, it can it can be tricky sometimes
But a lot of times it's really simple
The trickier part is probably the disassembly that's going to be required and
there is
easy way the easier ways but
Say you have a shorted module
Disconnecting the fuse like a lot of people get away with that. They'll disconnect the fuse to the module and it'll
Clean up the waveform
But if you have a grounded
waveform
And you found the offending module you disconnect the fuse it might not necessarily clean up the
the waveform
because they are the can chip
Inside of the module is internally shorted to ground. So disconnecting the power supply to that module won't fix that
physical short to ground so
Just something to put out there. I thought you might want to know that
Let me know if you need any more sense of direction where we could go from there, let me know your findings and
We'll keep in touch
We are heating up just like this relay did we are getting really warm and figuring out exactly what's wrong with our x6m
And mario helped us understand
Exactly why the screens are flickering exactly why we're experiencing the symptoms
We are and it all comes down to this relay
Now i've got the electrical system tester back out because it has a relay test function
We'll be able to confirm that our relay is good
I suspect it's good because it is turning on and off all those electrical functions
It's the whole reason why the iDrive is flickering why the speedometer is going in and out
It's because the short or the problem somewhere in the system
Is firing this relay telling it to shut off a bunch of those functions in the junction box electronics
And that's protecting everything else in the car now you see when I hooked up the relay it lit up right here
It sees that the relay is on which means that it's sensing the relay which tells us it's pretty much good
But we can go ahead and send power to it and the power is going through the relay as well
No problem. So this is a known working relay at this point. We will replace it just because well
That unfortunately just replacing this isn't going to be the end all to our problem
Now that we're equipped with a little bit more knowledge
We understand what this relay's function is and that it does work. Watch this. We're going to take it
We're going to leave it right here
We're not going to plug it into the fuse box and i'm betting you this car is going to act quite a bit differently
key
and the ignition
Everything powers up
This looks like it's flickering in person. It's not that's just the camera
No flickering on the iDrive screen
This all looks good put on the brake
And while we still have a bunch of trouble lights on the dashboard, but we got to remember it's a bmw, right?
No, but seriously, look at this
I'll sit here like this for a while
Nothing is flickering anymore. These rpms used to jump all over the place. It would go all the way down to zero
Look at it all it just it works. We obviously just can't run this car without that relay
Do you get what we just did there when we removed that relay from the system that main cutoff relay?
Since it's not plugged in it can't cut off power to these systems that are experiencing interference
But I could assure you in a short period of time by driving around without this relay in place
Well, it'll probably cause a lot of damage to those systems that relay is there for a reason
It's a safety net for very expensive electronics in our bmw
So based on everything i've learned about this bmw over the last few days and that bit of guidance from mario
I think we've got a good plan of attack going forward. It's pretty clear at this point
We have an issue in the kcan network
We need to figure out every single module that runs on this network and inspect not only the modules themselves
But their lines very closely and let's hope there's a visible issue here nine times out of ten that i've dealt with electrical issues
It is because of some sort of physical damage again, whether that be water intrusion
a lot of the stuff i've seen in the past has been due to a crash where a wiring harness or a module is
Compromised because of an actual crash damage fires things like that things that are really obvious this car at first glance
Just looks really clean now
I can't wait to figure out what is wrong with this x6m because I want to drive it so bad
This is one of the most exciting bmws I bought even
Maybe more exciting than the i8, you know like 0 to 60. It's just as fast as an i8
So if you're excited to see what it might be make sure you subscribe to the channel because you'll be notified next time
I release a video also if you feel like you learned something in this video
Be sure to hit that like button guys. I can't thank each and every one of you enough for watching today
I'll catch you very soon
You
