20+ Wilderness Survival Tips and Bushcraft Self Reliance Skills

Life skills
223 followers
We're going to start this off with one of the most useful things you're going to find in the woods,
and that is pine sap. Well, technically it's called resin, but you can call it whatever you want to
call it. Either way, it's very useful stuff and you can do all kinds of things with it. Pine trees
release this anytime they experience an injury to seal off the wound from any infections, and you
can harvest it yourself when it's fresh to use on your own cuts and scrapes for the same purpose.
It has antibacterial properties, and since it's sticky, it can help stop bleeding as well. It's
kind of like nature's liquid bandage and neosporin. It also happens to be highly flammable, which
makes it great for helping you to get fires going, especially in wet conditions because it'll burn
even if it's wet. Here I found a large chunk of it that I'm going to place on top of this pile of
dryer lint, which also makes great tinder. This large chunk of pine sap will burn long and hot
and will do a good job of drying out these damp sticks that I'm placing on top. It makes great
torches, which can be used as a portable light source at night or if you need to signal for help.
It can be difficult to ignite pine resin with a ferrocerium rod, but it can be done by finding
an older dry chunk of resin like this one and crushing it into a powder like I'm doing here
with the back of my knife, and just start throwing sparks at it. It might take a little while to
ignite it, but eventually it'll ignite. You can also use pine resin to make a temporary
waterproof patch for tents, tarps, rubber boots, or rain jackets like this one. I have a small hole
in this rain jacket, so I'm going to gather up some fresh pine resin. Just work it on there
over the hole until it seals, and you might have to add a second clump to it. It'll work best when
it's fresh, and this will create a waterproof patch. So I'm going to take this thing to the
stream, fill it up, and see if it holds water. And it's looking good. No water leaking through.
You can see the patch I made there. You can make portable fire starters that you can keep in your
pack for future fire making by wrapping pine resin with cedar bark so that they won't stick to
anything, and so that you can ignite it easier with sparks. After I've processed a strip of cedar
bark into finer fibers, I'm going to put the pine resin inside and roll it up. Now you can light it
with a lighter or give it some sparks from a ferro rod. This will burn pretty hot for about five or
six minutes, depending on how much pine resin you use. These are great for helping you to start
fires, especially in windy or wet conditions. Imagine wood that is soaked in oil or kerosene,
and that is what fatwood burns like. It can be found in dead pine branches. The section of the
dead branch that is closest to the trunk of the tree, known as pine knots, will be saturated with
flammable pine resin. And if you don't have a saw with you, you can break off small branches with
your foot or your hand as close to the trunk of the tree as you can get. It's very easy to light.
It'll burn for a long time, so it's really good for starting fires, and it's windproof. I have a stick
of fatwood here that I'm going to dunk in this stream, just to demonstrate how it lights even
when it's wet. To ignite it with a ferrocerium rod, you want to scrape very fine shavings off with the
back of your knife or with a scraper. Then I'm going to slice off some slightly bigger shavings
with my knife, and it lights right away. Great stuff. You can make long-lasting candles like the
one I'm going to make with this fatwood branch that I harvested earlier. Make a split in the top
about a third of the way down or so. Keep it propped open with a twig, and then do the same
thing in the opposite direction, crisscrossing the first split. And this is what it's going to look
like, almost like a miniature Swedish torch. And then I'm going to take my Zippo lighter, a good
wind-resistant alternative to the Bick lighter, and then I'm going to light my candle. Now you have
a long-lasting windproof candle for some light around the campsite, which also has a lovely
natural pine scent to it. You can make a larger version of this with a longer stick to use as a
torch. This particular torch I made lasted me about an hour, so you're going to get a long burn time
out of these. And if you need to put this out, find some water and dunk it. It'll burn while it's
raining, but it won't burn underwater. Make a stealth fire, also known as the Dakota Fire Hole.
Dig two holes next to each other, and then connect them underground with a smaller hole. The fire is
going to go in this hole, and as the fire burns, it's going to pull in fresh air from the air
intake hole, which is best to be placed upwind of the fire hole. So I'm going to get a fire going
in here, and once the fire gets going and gets nice and hot, it's going to burn very efficiently
and put out very little smoke. This is a very good option if you want a fire, but you don't want your
location to be known. Because as you can see, I'm walking up towards the fire, but I can't see it
unless I'm right next to it. Just be sure to watch your step and don't fall into it. You could twist
your ankle and burn your boot at the same time, and that's not good. It's also a very efficient
way to cook food and heat up water, compared to a normal fire. Think of it as kind of a rocket stove
in the ground. And once you're ready to put the fire out, all you have to do is fill the hole back
up with dirt, and you're good to go. It's almost like you were never there. A couple ways to modify
your BIC lighter. Wrap it with duct tape. Besides its obvious uses, duct tape also happens to be very
flammable. So now you have a fire starter and a lighter in one. I like to make kind of a hollow
tube out of it and give it a light. This will burn for a few minutes. It's also a good idea to pry off
the child safety guard that's on the striker wheel, and this makes for much easier striking
for if you ever lose dexterity and your fingers from the cold. One of the best natural tinders
you're going to find in the wild is birch bark. The bark contains oil that makes it waterproof
and highly flammable. I'm scraping fine shavings off the outer layer with my knife because I'm
going to pair it with cattail fluff, which makes a great combination for if you ever have to start a
fire with an empty lighter. The cattail fluff takes a very small spark, turns it into a flame,
but it goes out really fast, so I need the fine shavings of birch bark to catch the flame and
extend it. So I'm going to take my broken empty BIC lighter and all I'm going to do is give it a
spark. Make sure the cattail seed heads are fluffed up really good so that they catch a spark more
easily, and this can be added to your larger tinder bundle. If no other tinder is available,
you can always use your sock. Take your knife and start shaving off the sock lint off of your sock
and it'll make a great tinder that will take a spark from your ferrocerium rod pretty easily.
If you heat up a section of birch bark, it makes it easier to bend without breaking it,
and I'm going to use this to make a makeshift water filter. This is a good way to filter
heavy sediment out of your water. Bend your birch bark into a funnel and take a piece of clothing
like this cotton t-shirt I have here, and I'm going to place this into the funnel. Now all this is
going to do is filter out the sediment. It's not going to purify the water, which is why I'm letting
this drip straight into my metal pot, because I'm going to have to boil the water afterwards anyways.
And as you can see, this does a pretty good job of filtering out all that nasty sediment from the
water, and it's almost crystal clear now. Like I said, you still have to boil this, and it is
recommended to boil water for at least a minute. A good rolling boil. And you can see all the nasty
mud and sediment that I filtered out of it. If you have long branches but no saw and you need
smaller pieces, find two trees right next to each other and put your stick in between the two,
use it as leverage, and pull straight back until the branch breaks. Now you have a big messy pile
of logs. An easy way to transport them is to take off your belt, pile all the logs onto it, and
strap them up. Now you have a log carrier, which actually works pretty well. Carry your logs with
one hand and hold your pants up with the other. Cattail seed fluff is very compacted in the seed
but if you break them open, they fluff up really good. You've already seen me use this as tinder,
but there's another use for it. If you're stuck out in the cold without the proper clothing on,
you can use this as insulation. It acts just like goose down to keep you insulated from the cold.
The more fluffy they are in your shirt, the better they're going to insulate you.
Feeling nice and toasty. Say your lighter gets wet. When a lighter gets wet, needless to say,
it's not going to light. So first thing you want to do is shake it a bunch of times as hard as you
can, get all that water out of there, and then blow down into the top of it a few times to push
out any remaining water. Then you want to remove the safety guard that sits on top of the striker
wheel. Pry it off with something away from you because this thing can really shoot off of there.
If you poke your eye out, you're going to have bigger problems. Then you want to take the lighter,
hold it upside down, and roll it back and forth on your pants a bunch of times. You just want
to keep doing this over and over again until the lighter is dry enough to work. Now there's
another way to do this if you're worried about wearing down the lighter's ferrocerium rod.
Take the lighter and dry out the striker wheel with your shirt, turning the wheel as you go,
and then that'll dry it out pretty quick.
