How to make a cup on the pottery wheel from start to finish

Handicraft occupation
458 followers
Making a cup or a mug from start to finish is one of the most satisfying things a potter can do. This is my step by step process that I take to making my cups on the pottery wheel.
✨
Socials:
Instagram:
@mae.ceramics
https://www.instagram/mae.ceramics
Website
https://www.maeceramics.com
Sometimes the shop is sold out, sign up to my mailing list for updates on drops!
secondfloor.co.uk
✨✨✨
#DIY #pottery #tutorial #ceramics
Cups are my favourite thing to make as a potter.
They're so satisfying, there's so many different variations and they're obviously very useful.
This is how I make a cup from start to finish.
Before the wheel I have to weigh and wedge my clay up and then I sit down at the wheel
and get to throwing.
For this cup I used 280g of clay.
The most important part of throwing is making sure the clay is properly centred.
I always cone the clay up and down a few times, especially today as I'm using reclaimed clay.
Coning helps to align all of the clay particles and it kind of gives it an extra little wedge.
Once it's centred I open up the clay puck, widen it and compress the base a little bit.
Then I pull up the walls.
When making a straight sided cylinder it's really important to focus on applying more
pressure to the outside fingers rather than the inside ones and this will help to make
a cone shape or like a volcano shape on the first pull, fighting the centrifugal force
that the wheel is putting on the clay.
On the second pull I let the clay flare out a little bit more.
And after a quick measure up I do the final pull and I do a little bit of finessing in
the shaping department at the same time.
Then I'll use a rib to get rid of any excess slip on the outside and I always compress
the rim in between to keep everything nice and sturdy.
After that the throwing is done and it's time to remove it from the wheel.
With all my pots I remove the water from the inside and use my wooden knife tool to create
a little chamfer for the wire.
I like the sliding method when removing pots from the wheel so that I don't have to dry
my hands in between each cut.
So I squeeze my sponge out onto the wheel head and then when pulling the wire through
I make sure to drag some of that water with it.
And that pulls the pot off the wheel and then I can pop it off and place it onto a wear
board to dry.
These dried overnight but because it's still a little bit chilly here in London at this
time of year they needed a little bit longer before I could trim them.
When the weather is like this I find that flipping the pots over and giving them another
hour or two to dry upside down really helps.
Sometimes after using the water method to remove the pots they can get really stuck
to the bat though and this one was very stuck.
So I decided to wire it off and sometimes they kind of like pop off halfway through
like this pot did and it left a little uneven half moon of clay that I had to even out while
I was trimming.
And the other one popped off the bat quite easily when I coaxed it off.
I like to make my handles at this stage so that they can harden up a little bit whilst
I trim.
For a long time I pulled my handles but I found that the slightly rounded look of pulled
handles meant that it wasn't quite matching the squared energy that my pots have so I
decided to make them with slabs instead.
I do think that pulling handles is a skill that all throwers should know though so one
day I'm going to make a video about different styles of handle.
Anyway I roll out a big slab and then I use these guides to cut a whole lot of long strips.
Then I cut each strip into three-ish smaller strips and they become blanks for my handles.
I give each side a sponge and then I place them onto this dowel to form their shape.
For trimming I stick my pot down by wetting the wheel head, swirling it around a little
bit with the wheel moving to create a bit of slip, check it's centred and then I give
it just a little tap to stick it down.
These need very little done to them at this stage, it's just kind of an exercise in tidying
up really.
I drag my loop tool across the base, a quick drag over the walls and then I create a more
refined chamfer which is a 45 degree angle on the shoulder and that's it.
I swipe it down with a sponge and it's ready for its handle which are now leather hard
after trimming all of my pots.
I like to make sure that the curve of the handle is the exact round arch that I like
and I have found that this random little pot that I made years ago is the perfect former.
The tails both get trimmed to the form of the cup and then scored.
The cup where it will hold the handle is also scored.
A little slip is applied to the handle and then I just kind of squash it on.
When I press the handle on I always make sure to support the inside of the cup with my other
hand to stop it from warping or misshaping at all.
Then I fettle each surface of the handle where it joins to the cup with my wooden knife tool.
Then I follow up with a quick wee sponge down to get everything looking real beautiful and
spick and span.
After drying out for a week or so the cups can be bisque fired and then glazed.
Full disclosure, the pot that I am showing you how to glaze on is not the same pot.
The kiln hadn't quite cooled down enough for me to unload it yet so we're using a little
stand-in.
For glazing you need glaze, a mixing brush, some water and a sponge and your pot.
You also need a jug or something to pour your glaze with.
You can see that my glaze has separated from the water on top so it needs a really good
mix.
I always mix it for a minute or so and if it's still lumpy I'll pour it through a sieve.
This glaze was good to go after just mixing though.
So I fill up my measuring jug, I pour it into the cup, hold it for a few seconds and tip
it back out.
Then I can hold the cup on the base, plunge it down into the bucket with the rim down.
I'll hold it for a few seconds then I pull it back out and shake off any drops.
Flip it back over and I dab the fingerprints with a little bit of extra glaze to fill them
in.
Once it's dried to the touch I can hold it really firmly, turn it over and sponge the
base off.
Then it goes back into the kiln for a second firing and it's finished!
It's hard to believe how much of a change that ceramics go through in the kiln.
I really adore this honey glaze that I made recently, it's quite interesting how it goes
from this red colour to this beautiful deep yellow.
That's it, as always please let me know if you have any questions, follow me on the other
socials at may.ceramics and I will see you next week for another video.
Bye babes, love you!
