How does a worm drive work¿ ¦ statically and dynamically self-locking (self-braking) explained .

Terrific Physics
40 followers
Worm Drive The worm is a special type of gear.
Here the tooth wraps around the worm's shaft like the thread of a screw.
The gear that meshes with the worm is called the worm gear.
This type of gearbox, consisting of a worm and a worm gear, is generally referred to as a worm drive.
The worm can be regarded as a special case of a helical gear.
Imagine a gear with only one tooth.
Now increase the helix angle to such an extent that the tooth winds around the gear several times.
The result is a single-toothed worm.
It is also possible to imagine that instead of one tooth,
two or more teeth are wrapped around the cylindrical gear at the same time.
In this case, the result is a double-toothed worm.
The number of teeth on a worm is also referred to as the number of starts.
Therefore, one also speaks of a single, double, or multi-start worm.
Single-start worms are the most common type,
but in special cases the number of starts can be up to four.
So note, worms are basically teeth helically wrapped around a shaft,
which screw into the worm gear and thereby drive it.
Since the number of starts of a worm is equivalent to the number of teeth of a gear,
the number of teeth used to determine the transmission ratio
corresponds to the number of starts of the worm.
The fact that the number of starts on a worm corresponds to the number of teeth
on a conventional gear is also immediately apparent
in the animation of the single-start worm drive.
For each complete revolution of the worm, the worm thread moves one position further.
This means that the worm gear moves by one tooth.
Compared to a conventional gear,
the worm in this case actually behaves as if it had only one tooth on its circumference.
In contrast, with one revolution of a double-start worm,
the two threads would each move further by one position.
A total of two teeth of the worm wheel would then be pushed further.
In principle,
the double-start worm would then behave like a conventional gear wheel with two teeth.
The animation shows the comparison between a single-start worm and a double-start worm.
Note that the worm gear meshing with the double-start worm rotates twice as fast
as the worm gear of the single-start worm,
as the single-start worm drive has a higher transmission ratio.
Due to the generally very low number of starts of the worm,
usually single-start,
and the high number of teeth of the worm gear,
the transmission ratio of worm drives is therefore very high.
With worm drives, ratios of over 100 can be achieved in a space-saving manner.
Because several sections of the worm are usually meshing with the worm gear at the same time,
such gearboxes can handle very high loads,
which means that very high power can be transmitted.
Due to the constant sliding of the flanks between the worm and the worm wheel,
and the necessary lubrication,
worm gears are also very quiet.
In worm drives, power is transmitted almost exclusively by the sliding of the flanks,
like a screw in a thread.
Worms are therefore a special case of so-called screw gears.
However, unlike screw gears, which produce a punctiform flank contact,
worms produce a linear flank contact.
This has the advantage of transmitting more power at higher transmission ratios.
Due to the sliding and the resulting friction between the flanks,
the efficiency of worm drives is lower than that of conventional gearboxes.
Due to the friction on the flanks and the associated generation of heat,
worm drives must also be cooled in addition to lubrication when operating at high speeds.
Lubrication and cooling are provided by special oils.
The low friction and low wear sliding of the flanks in worm drives
is already taken into account when selecting the appropriate material.
Case-hardening or nitriding steels are generally used for worms.
Case-hardening or nitriding gives the worm a wear-resistant surface.
However, this means that the worm, which is expensive to manufacture,
is only optimally protected against wear if the wormwheel is made from a slightly softer material.
For example, tin-based bronze is a suitable material for wormwheels.
The combination of bronze and steel provides excellent sliding properties
even under less than optimal lubrication conditions.
In practice, however, the specific material pairing always depends on the individual case.
Worm drives can be classified according to the shape of the worm.
If the shape of the worm is cylindrical, it is called a cylindrical worm.
If the cross-section of the worm gear imitates this cylindrical profile on the circumference,
it is called a globoid worm gear.
This type of gearbox is called a cylindrical worm drive.
This design is preferred because a cylindrical worm is relatively easy to manufacture.
In a modified version, the shape of the worm describes an arc,
which is adapted to the shape of the globoid wormwheel.
This is known as a globoid worm or enveloping worm.
Compared to a cylindrical worm, more sections of a globoid worm mesh with the worm gear.
Globoid worm drives can therefore transmit higher torques than cylindrical worm drives.
The production of a globoid worm is relatively complex and therefore expensive
compared to a cylindrical worm.
For this reason, globoid worm drives are used less frequently.
In special cases, the globoid worm can also mesh with a conventional helical gear.
However, this requires the worm to be specially matched to the helical gear,
which makes manufacturing more expensive.
However, the advantage of such a variant is the radial positioning of the worm gear
when combined with a simple helical gear,
which allows a greater tolerance than is the case with a globoid worm gear.
The advantage of worm drives is that they are self-locking.
Gearboxes are described as self-locking if the power can only be transmitted in one direction.
This means that the gearbox can only be driven by the input shaft.
The gear unit cannot be set in motion by the output shaft.
Worm drives are often self-locking due to the way they operate.
The reason for self-locking is the low pitch of the worm threads.
Although the worm can drive the worm gear with its screwing motion of the flanks,
the worm gear cannot produce a rotational motion of the worm.
For this reason, self-locking worm drives are always driven by the worm and not by the worm gear.
It should be noted that single-start worms generally have a smaller lead angle than multi-start worms.
Single-start worms are therefore more often self-locking than multi-start worms.
Conversely, this means that self-locking can also be specifically prevented with multi-start worms,
if desired.
Self-locking worm drives are used in lifting mechanisms or cable winches, for example.
This prevents the winch cable from unwinding automatically when the motor is switched off.
This is also referred to as statically self-locking.
An additional brake can be dispensed with if self-locking is strong enough
and cannot be released by vibrations.
However, if this is the case, you will often hear the gearbox rattle.
Depending on the application, it may also be necessary to ensure that the gearbox
stops automatically when the load is lowered and the motor is turned off.
This is referred to as dynamically self-locking or self-braking.
As the examples show, there are two types of self-locking.
On the one hand, there is self-locking in the rest position,
which is referred to as statically self-locking.
The point here is that the static friction acting on the flanks is not overcome and
the worm gear does not reverse the direction of rotation on its own.
On the other hand, there is self-locking out of the operating state,
which is also referred to as dynamically self-locking.
In this case, the sliding friction must slow down the gearbox after the motor has
been switched off so that it automatically comes to a standstill.
Self-locking is always associated with friction,
without which there would otherwise be no self-locking.
Self-locking gearboxes therefore always have a lower efficiency than non-self-locking gear units.
The efficiency of self-locking worm drives is usually below 50%.
Above 50%, worm drives are often not self-locking.
If self-locking is not required, the focus is usually on maximizing efficiency.
Efficiencies of well over 90% are possible with non-self-locking worm drives.
If high efficiency and self-locking are required, the worm drive must be equipped with a brake.
Self-locking can become a problem when large masses are moved by the worm gear.
If the worm drive is suddenly switched off,
the worm gear will continue to move a little due to the inertia of the driven mass.
However, with self-locking, the worm will not allow any rotation,
resulting in enormous forces acting on the flanks, which can lead to worm breakage.
In such cases, the worm must not be stopped abruptly,
but must be allowed to rotate a little when the motor is switched off.
Special lubricants can help the worm to over-travel.
It may also be necessary to install special traveling devices that
slowly bring the worm drive to a standstill.
I hope you enjoyed the video and found it helpful.
Thanks for watching.
