Restoring the painting of the Virgin Mary (narration)

Sculpted Rome
10 followers
So here I'm going to do another narrated walkthrough of the restoration of this
painting of Mother Mary. It's not meant to be instructional or
exhaustive, just to give you guys an idea of what I'm doing.
This painting was pretty damaged. It had been exposed to moisture which resulted
in a lot of flaking. There were punctures and tears. The
painting was quite dirty and there was an old varnish on it.
Obviously there's a lot of paint missing which also needed to be addressed.
So the first step is to remove the painting from the stretcher and I'm
using an upholsterer's tack pulling tool to remove these nails.
I just need to get it off the stretcher so that I can start working on it.
But I want to preserve the tacking edge as much as I can.
The next step is to clean the back and this is just to get rid of the
dust, dirt, and grime that's trapped in between the stretcher bar and the canvas.
The next step in the conservation process is to repair the tears and what I'm going
to be doing is something called bridging. That's where I take little strands of
I was just cutting them off and a conservation adhesive and I will lay
these strands perpendicularly across the tear.
The reason that I do this is to provide some stability to the tear so that it
doesn't move, to provide a nice foundation for the fill-in medium which
will replace the missing pigment, and generally just to hold the tear together.
So it's slow going and after the strands are laid down I have to make sure that
they're fully saturated in adhesive and then I can press them and I'm going to
use a piece of silicone release film and a pad of felt.
The release film makes sure that nothing sticks and the felt is just a cushion
and then a steel weight.
Next I'm going to be cutting off pieces of Belgian linen for the strip lining
and that will go on the new tacking edge.
I'm going to fray the edges of this linen so that the edge doesn't impart
upon the face of the painting.
If I don't do that the crisp edge of the new linen can sometimes show through
on the face of the painting.
Now here I'm using a conservation adhesive film it's iron-on and then I'm
ironing on the new piece of Belgian linen and as I go I use a weight to make
sure that it dries flat.
Cutting off the excess and there you go the whole thing has been strip lined.
In this step I'm going to start cleaning the painting and the first step
is to remove the surface grime.
So I'm using a paste that I mix to loosen up and remove the accumulated
surface grime and that's dust, dirt, oils, just grime that's sitting on the
surface of the painting.
And I have to remove this stuff first before I can get to the varnish layer
because that layer of surface grime prevents the solvents from penetrating
through and softening up the varnish.
If I were to just try using solvents it would be ineffective and then I would
probably go to a more aggressive solvent and eventually do damage to the
painting.
So I'm making my own large swabs because cleaning paintings with q-tips is not
effective and here I will start to remove the surface grime and the old
varnish and you can see it start to come up there.
I work slowly and I work in isolated sections because I like to keep control
of what I'm doing.
Here working on metallic letters I'm using q-tips because I want to just
focus on those letters.
Now here I'm squaring up the stretcher.
I need to make sure that it's square before I stretch the painting to it.
These little nails are going to make sure that as I'm handling the stretcher
it doesn't flex or distort and become a parallelogram.
So painting gets laid down onto the stretcher and then I will use steel
upholstery tacks to secure it to the stretcher.
I use a magnetic hammer and steel tacks.
I prefer them over staples for a lot of reasons.
I think they're superior.
Some people will debate that with me but this is my studio so I get to decide
on the rules.
I like to put the tacks in about an inch to an inch and a quarter apart.
I feel that gives good coverage without overstressing the tacking edge or the
stretcher.
Sometimes I'll use a pulling plier to add tension but in this case I don't
want to so I'm just using my hands and I can add pretty good tension with just
my fingers.
I'm going to clean up the corners and fold over the new Belgian linen and
secure it with smaller tacks.
I prefer this as opposed to staples or glue.
I think it looks nicer and it's easier to remove in the future.
I'll clean up the corners again just making it nice and tidy and then the
next step is going to be cutting new keys for the stretcher.
Now these little wooden wedges are keys and what they will allow me to do is
add tension to the stretcher.
Because the stretcher's joints are not glued together I can insert this key and
tap it with the hammer and slowly expand that joint and if I expand all four
joints I can enlarge the stretcher and add tension.
Here I'm using fishing line and a tack to secure the key so that it doesn't get
lost.
If that key falls out it falls in between the painting and the stretcher
bar it will create a bulge and there's no reason why that should ever be lost.
Here I'm using a putty to fill in wherever there was missing pigment.
This is necessary because if I don't fill this in and just go ahead and
retouch it you'll see that as an indented area and it just won't look right.
I'm removing the excess.
All I want is where the missing pigment is to be filled in.
And now comes the retouching process and this is the long and slow and
time-consuming tedious work of putting the painting back together.
Here I'm using a conservation pigment and a medium and I'm just going to mix
my colors and slowly add them to the painting where the color is missing.
You'll notice I'm using a very very small brush and I'm going very slowly
and I'm just adding pigment where pigment was lost.
As a conservator it's my job to restore the painting to how the artist
envisioned it not to make editorial decisions so it's inappropriate for me
to glaze in large areas or to add medium where there already is medium.
This is again I said it's just slow going and methodical and some days I have to wipe it all
off and start over because the light wasn't right or because I'm not satisfied with the retouching
but the good thing about using archival and reversible pigments
is that I can remove my retouching without damaging the artwork.
And then finally I will varnish the painting and here I'm mixing
the varnish a combination of matte and gloss varnish with a UV stabilizer
that will prevent the varnish from yellowing and I'm going to brush it on the painting.
Generally I prefer to brush my varnish as opposed to spray it sometimes I do spray
but in this case a brush is fine it gives me a little bit more control
and I just prefer it there's no right or wrong way to add varnish other than to go evenly
methodically and to keep in mind that you can always add more varnish when the painting's wet
but removing varnish if you put too much on is much more difficult.
So once the painting is varnished it is all complete and you can see the final product here.
So the clients were really happy with this I was really happy with it
the painting is now stable and sound and will be good to go for the next 150 years.
All the work that I've done is archival so none of it will damage the painting
and it's fully reversible so if in the future another conservator decides to
take my work off and give it a go it should be pretty easy for them.
So thanks for watching I hope you enjoy it!
