Part 2 in a series teaches proper setup, configuration, and troubleshooting of wireless devices. We look at "mesh wireless routers", more troubleshooting, and items in your home that impact wireless and adjacent channel interference. We also look at wireless items in your home that slow down everyone.
https://www.metageek.com Professional Wifi software, spectrum analyzers, and more www.ekahau.com Free WiFi heatmap software for laptop https://www.arubanetworks.com/ Whitepapers, webinars https://www.aerohive.com/ videos, webinars, and more https://www.ui.com/ cool outdoor wireless products https://www.acrylicwifi.com best free WiFi analyzer for Windows http://wlanpros.com/ excellent videos and blogs on Wireless Google Play apps: WiFi analyzers: Wifi Analyser by keuwlsoft WiFi analyzers: Wifi Analyzer by farproc NOTE: do not install more than one mobile phone WiFi analyzer at a time My favorite cell tower analyzer app: RTR-NetTest 3G/4G/5G IPv4 & IPv6 by RTR-GmbH
Welcome back to our part two of our home wireless comprehensive setup
troubleshooting and a review of good solid wireless security.
Large homes and multi-story homes if it's a two-story even a three-story
these still provide significant challenge to RF designers
for the home. Mesh router technology was introduced to address these large homes
and inadequate wireless coverage. They gained a lot of attention in the last
few years addressing these problems and especially
when Google introduced their home Wi-Fi which was a mesh router. I'm going to
show you the pros and cons to them. Right now they're still pretty pricey.
Wireless routers are a combination of a wireless router configured in gateway
mode and that's just exactly what you normally buy from a store.
Gateway mode is the default configuration of most wireless routers.
Then you add to that one or more wireless devices
sometimes they call them satellites that act like a wireless bridge
and an access point. To get this all to work is
complicated so the third component is complex software that makes
all this easy to work and easy to set up. Mesh wireless solutions
as seen in the pictures below are still pretty pricey but they're easy to
configure and they give you good RF coverage
even in complex house layouts. The most attractive part
of mesh routers has been the vendor's effort to make the software that a user
has to use to set up and configure and maintain
really easy to use. This diagram shows you
how many devices to purchase depending on your home configuration.
If you'll notice these none of these devices have external antennas
and most of them are relatively low RF power. Next we're going to go look at
these items in your home that really impact
Wi-Fi transmission. If I put a wireless router on one side of
a wall in your home and let's say its power output is 100
milliwatts. By the time it passes through that wall
it will come out the other side with 50 milliwatts.
That is called a 3 db loss. That's pretty drastic. On the chart on the
right hand side is a list of material that may be found
in your home and it shows a column for 2.4 gigahertz radios
and a column for 5 gigahertz radios. You can look at the material
and the db loss. For example an interior drywall
3 db loss for 2.4, 3 db to 5 db loss for a 5 gigahertz radio.
Come down to a brick and concrete wall 6 to 18 db loss at 2.4
at 5 gigs 10 to 30 db loss. In other words if we go back to our wall
and it's a concrete one and I've got 100 milliwatts on one side
I will have zero milliwatts on the other. There's a lot of items in your home you
just don't think about when you're thinking of
wireless. We have a kitchen with a lot of metal appliances
in the kitchen. These reflect radio waves. The room behind this kitchen can be
dramatically impacted because of that metal. I've seen
corporate offices as well as homes using wallpaper that has metallic
metallic material in it. This is a copper wallpaper.
It has metal impregnated into the wallpaper.
It really looks great on the wall but man it impacts the wi-fi.
To save energy many houses are employing radiant barriers which are simply
metal material put on the roof area and in the walls of the home. This really
does save energy but the metallic shoelace really plays
havoc with your cell phone and your wi-fi connectivity. Let me share
some advice if you decide to purchase your own wireless router there's things
you need to consider. When a internet provider brings
internet to your home they generally bring a broadband modem
that has a router and wireless built in. It's kind of an all-in-one package. If you
decide to buy your own wireless router you do not want this. It will force you
to daisy chain your router into theirs. Daisy
chaining wireless routers is to be avoided. As long as your
internet provider has a router on your network they
control your network. You lose admin control of your home.
Because that device has wireless it can create adjacent channel
interference which is a real problem. After you have purchased your own
wireless router call your internet provider and ask them
to replace the device that they brought to your
home with a cable modem. A cable modem is simply an electronic
device that converts broadband into ethernet. The only thing you should have
in the back of that cable modem is an ethernet jack. In other words internet.
Now you can hook up your new wireless router
to the cable modem and you have control. You also
avoid that adjacent channel interference from their
wireless device. When we add devices like 4k tvs
gaming consoles that stream high definition content
these high bandwidth devices will impact everyone on your wireless network. When
streaming high definition content you can pull up to 25 megabits per second.
Some 4k gaming streams can require up to 100 megabits per second.
Google strata's new gaming platform if you run 4k hdr 60 frames per second
and 5.1 surround sound will require 35 megabits per second.
When you have these types of high bandwidth devices
in your home you need to look at the cpus
in your wireless routers. Because of high bandwidth
the cpus in our wireless routers have to be as powerful
as our laptops and our desktops. Companies like
Asus are putting in quad core 64-bit processors inside of their
wireless routers. You kind of have to have this if you're
going to stream 4k and serious online gaming. Mr Vanderbilt I
just bought a brand new router wireless device. It's got a
gigantic cpu in it and i'm still getting awful wireless. Let me
show you some things that you may not think about that are impacting your
brand new wireless router. So the kids have some old tablets that have kids
apps on them. It connects to your wireless network. You've got an old e-reader
that connects to your wireless network and you've got that old camera in the
front door you've had for 40 years and it connects
to the wireless network. Those are your problems.
Just as important as it is to buy a new wireless router
is that you need to look at the items that are connecting to your wireless
network and do an inventory to see are they old
radios. Do I have an old tv with an 802.11g
radio? Do I have kids toys that connect to
my wireless network and they have an 802.11n
Do I have devices connecting to my access point
that are five years or older in my home? Are you telling me that Mr
Vanderbilt that I have got to replace everything in my house to get good
wireless speed? Well no, but you do need to look at the
devices that have old radios. 802.11g runs at 54 megabits per second.
That's very slow. It's just like this beautiful interstate
with two lanes where you can go 75 miles an hour
and you get a wide load that straddles across
the interstate. Nobody's going to go fast. When this old radio connects to your
wireless router it slows that router down. If you've got
kids toys on and they're on all the time
your router's running at a very slow rate. You're pulling your hair out.
The easiest solution to this problem is simply don't allow these
older radios to connect to your wireless radios. Here I have a
TP-Link wireless router and I'm going to show you how to configure it so that
those old radios don't connect. Now your router interface may be a
little bit different but I'm going to show you
in a TP-Link router and an ASUS. So let's go to wireless.
I'm going to go to advanced and here we see our 2.4 gigahertz wireless.
We have two 5 gig wireless radios. I'm going to go to advanced.
Then I'm going to come over here to the wireless tab and drop down
into wireless settings. This is where we can right now this radio will talk to
a 802.11 b radio which we don't want. A g radio which we don't want and an n
radio. We don't want that so we're going to drop
this down and we're going to say only n and above. So
immediately by doing this we have cut off
all the old radios in our house. Then we'll hit the save
and we're then we can come up save. Come up to
the 5 gigahertz radio and here we're going to allow
maybe n and ac only. These are newer standards. Newer radios will allow those
to again save. Go to my last radio over here
and configure it to n and ac only. That way older radios cannot connect to
your access point. So this time I'm in an ASUS wireless
router and I again I'm in the advanced settings of wireless
and I come up here to wireless mode. Here it's set for auto which we don't
and what we want is for this 2.4 gigahertz radio
only to connect to n. Now it will when a g radio tries to connect or a b
radio it just ignores it. We're going to go ahead and
apply on the 5 gigahertz radio. Let's go up here
and change this to 5 gig and here we go to the wireless mode
and in this particular one we can choose the n
only. It does allow us to connect to legacy which would be
an 802.11a radio which we do not want to connect to our 5.
In this case we can probably leave it n only and we've taken care of
our 5 gigahertz. If you have an old if you have an older laptop
and you want to upgrade the wireless simply disable in device manager
your old wireless radio. You can add one using USB.
Make sure it's 3.0 or 3.1. Also look for external antennas. Avoid any
wireless radio that does not have an external antenna.
They use antennas but they're built on the printed circuit board.
They just don't have the reach. This USB radio
looks really good. It's got good speed. It's got dual band radios. It's got a 5
gig radio, a 2.4 gigabit radio. It's got a high
gain antenna. All great things and it's USB 3.0.
The thing to be careful is if they don't build enough heat sink capability
in that form factor they simply won't last.
Those radios get hot. Upgrading your desktops are pretty straightforward.
Make sure it has external antennas. Most people
are not aware of the worst type of wi-fi interference.
It's called adjacent channel interference and it's primarily caused
by your neighbors. Looking at this chart below you can see
that my 2.4 gigahertz radio can be put on any channel between
1 and 11. So it can be on 2, 3, 4, 5. The problem is over here
where I start putting wireless access points close together.
When they get close together then I must have
each of them five channels apart. If I have this scenario over here where I
have a wireless router on channel 4, another one on 5 and 6, I begin to
experience adjacent channel interference. This
really impacts your wireless. Remember the key is that the
radios are close together. So here's a map of a
group of homes and you can see let's say that
these are single family homes and they each have an access point
shown by the yellow dot. As long as there's enough distance between them
it really doesn't matter what channel that all of these homes
have their access point on. It doesn't matter they could all be channel one
but because there's enough distance between them by the time the radio
transmits outside this concrete wall it's dead. There's no RF transmission
to speak of between the two buildings. So in this scenario
having all the radios on the same channel really doesn't matter at all.
But what if I have an access point in this home that's
right here on this side of the house and I have an access point
over on this side of the house. Now I have about 15 feet between them. If
they're on the same channel or not at least five channels apart
we're going to get adjacent channel interference.
Now come over to the map where I've got an apartment complex.
Now we've got three-story apartments side by side.
Each of them have their own access point in them and you can begin to see the
problem really quick. Now these apartments and access points
in each of these apartments can be very close together.
This is where adjacent channel interference causes havoc.
In our part one of our video we talked about
how you can download the Wi-Fi analyzer onto your Android phone.
To check for adjacent channel interference in your home
or your apartment open up the app and launch it
and kind of walk around in the case of a single family home.
Kind of walk around your home all the way around and you'll be able to see
like here on the right hand side in my phone I can see
all the SSIDs of my neighbors but the signal
is way below negative 80 dbm. So as I walk around the house I can see
those radios from my neighbors but because the signal is so low I don't
need to worry about it. No adjacent channel interference in my
house. So now I'm in the apartment complex and I'm looking around with my
my smartphone and my Wi-Fi analyzer and I notice the SSID of my neighbor
and I'm looking at the signal level that's negative 59 dbm
and negative 60 dbm. Those the signal from my neighbor's wireless
routers are strong enough to cause problems with
adjacent channel interference. I want to go in my wireless
routers interface and make sure that my radios are at least
five channels away from channel 10. In really dense apartment condo
environments this can be really really challenging.
When comparing this problem with 2.4 and 5 gigs
5 gigs has over 24 non-overlapping channels.
This is really easy to do with 5 gigs but with 2.4 you only have three
one six and eleven. In an ideal world if we had
three apartments close together we would like to have them on channel 11
channel six and channel one. Remember just because you can see your neighbor's
SSID doesn't mean you're going to have problems.
If their signal level is minus 80 dbm or higher don't worry about it. 5 gigahertz
range if you see a strong signal from your
neighbor and let's say he's on channel 64
on the 5 gig and you're both using the same channel
you can just move yours a couple channels away either to channel 104
channel 52. In most cases 5 gigahertz will be a
less of a problem one because a limited range of 5 gigahertz.
If you haven't been noticing I've been giving you a ton of troubleshooting
ideas in this entire presentation. Let's talk about some of the items I haven't
covered to this point. When troubleshooting always start simple
and work to the more complex. So start by rebooting the wireless router
power off the tv the laptop the camera and try reconnecting. Use these phone
apps that I've shared with you to verify you've got
enough wireless signal to the device. Update your laptop wireless adapter
check for tv firmware updates. If your connection is slow and you have a 5 gig
and 2.4 gig radios switch your wireless connection to a different radio.
Just try something different. Also check what has changed in the home.
Have you added a new 5x5 mirror and you hung it
in the living room? Did you add a gigantic refrigerator to the kitchen?
Or has the internet provider changed out your wireless router
for a better one? Coming up in part 3 of this video series on home wireless
comprehensive look at wireless security. If you cannot take time to watch
any of part 1 or part 2 be sure to watch part 3.
We're also going to look at how does 802.11ac provide
high range and bandwidth and what are the new
802.11ax devices going to provide for your home network.