Damaged 1950s Cuckoo Clock Restoration

Clockwork Chronicles
19 followers
Hey, thanks for stopping by. Next up on the bench we have a cuckoo clock and this one's
definitely seen better days so let's get right into it. Well here's our first problem. The cuckoo
has no way to open and close the door so he's trapped inside and this deer looks like he's
taking a tumble so we'll have to address these various case issues later on. So I'm just going
to poke around in here and see how things are working. It looks like the bellow lifting lever
is catching on something so that's not good. The bellow sounds okay but the bellow on the
other side has got some problems for sure. So before I start tearing this clock down I'd like
to first make a test stand so I can access the front and the back of the clock while it's running
and it's got to be set up high enough for the weights to hang and run for a little bit.
So I'll head to the wood shop and get this made up.
So every time I use the table saw now I always wear this face shield. A few years back I had
a piece of oak kick back on me, hit me right in the mouth and chipped a couple teeth. I had to
get stitches in my lower lip and my lip was numb for maybe six months or so. I think I got pretty
lucky because it could have done a lot more damage than what it did and you know it could have
knocked me out. I could have fell forward into the table saw which would have been bad because it was
running. So definitely make sure that you take the proper precautions when you're working with
some of these power tools because you're going to wish you had if something goes wrong.
All right so the stand's made and we can go ahead and see how it's running.
So it does tick so that's good news but there does seem to be a problem on the chime works
side of the movement so I'll have to try to figure out what's going on there here in a little bit.
All right so let's get the movement out of this case. First thing we got to do is get
the hands off and those are held in by a nut and a washer and then the hands should just pop right
off. They're a little dirty but they should be easy enough to clean up. So the door on the side
of this cuckoo clock is nailed shut. I think it's because it's not used in this model. I think
there's some clock movements where it allows the user to synchronize the cuckoo. So if the cuckoo
gets out of sync with the hour count they can open the door and pull on a lever and
get everything synced up but this movement doesn't have that feature in it. So in order to get the
movement out these bellows seem to be in the way so I went ahead and took them out first and this
one seems to be in good condition. There's no rips or tears and so let's get the other one out and
see what we're looking at. So these bellows are held in by a screw and a nail and once you back
the screw out you got to pry the bellow away from the inside wall and they just pop right out.
There's a couple different ways you can fix a ripped bellow.
You can just buy a new bellow online, pop off the old bellow and glue on the new one
or you can actually repair the bellow material on the existing bellow itself. I figured it was
better to keep the clock as original as I could so I had to figure out how to
replace this material. Let's get into that. So I replicated the existing bellow using some
scrap wood and then practiced installing the new material and I think it went pretty well
so I think I'm ready to give it a shot on the real one. So there's different kinds of material you
can use to fix damaged bellows. It seems that most people have used a product called Tyvek
and that's what I decided to go with. Some said they've used worn dollar bills which I wasn't
going to try and some said they've used priority mail shipping envelopes. The problem with the
shipping envelopes is the material is really stiff and that causes a problem with the bellow closing
and the bellow closes by gravity mainly. There's a weight at the top portion of the bellow which
causes the bellow to shut and if the material is too stiff it won't close and then the bellow
won't make a sound. The bellow needs to open about one and five-eighths of an inch so I'm making this
one and seven-eighths of an inch wide and that gives me about an eighth of an inch
to glue to the top and the bottom of the bellow and I'll make this seven inches long so it can
wrap all the way around the bellow. The sides are two inches long by an inch and a half so that's
seven inches total. I'll go ahead and get the hinge cut and save that for later and then I'll go ahead
and mark the center line on the top and the bottom and this will just help me line things up here in
the next step. So I decided to use Titebond wood glue and that's what I used on the practice bellow
I made and it held up just fine so that's what I'm going to use here. So I thought I'd try to be
clever and pre-crease the Tyvek and I ended up creasing it the wrong way so that didn't help
me any. I was just trying to make sure that when I did this step I creased it evenly all the way
through. Next we can go ahead and get the hinge glued on and I decided to wrap a rubber band
around the top and the bottom and that held them firmly together and in line with each other.
All right look at that starting to look more and more like a bellow. So next thing we got to do
is get the sides glued down. I'm also trying to make sure I spread the glue out correctly
that way there's no way for air to escape or anything like that.
One nice thing is it didn't seem to take too long for the glue to dry.
I had to wait maybe 10 to 15 minutes and then I was able to start working with it again.
Now that most things are glued up I can start going around and removing all this extra material.
Another thing I want to point out is when you're working with an X-Acto blade or
a blade similar to this one is you just don't want to lay it down on your desk when you're
finished working with it because it is round and it'll roll right into your lap.
And you definitely don't want that. So those little triangle bits that are hanging off the
back there are going to wrap around and hold the hinge in better. So that's why it was important
to make this strip seven inches long. So the split down the side of this chamber has really
been bothering me. So I went ahead and checked to see if it made a difference in how it sounded
and it did. So I'll have to get that fixed. Finally got the bellow fixed and it sounded
pretty good and we can get the movement out now. So I'm going to go ahead and get the bellow
lifting wires out of the way. And these are different lengths so I'm just going to take
note of that. And there is a slight bend to these lifting wires and I'm not sure if that was done
on purpose. They could have had a bend in them to make sure that the height is correct between the
bottom of the movement and where the bellows actually sit. So if there's not a problem
I'll just leave them like that. This is the strike lifting wheel and this is what the
bellow lever was catching on. But it looks like there's a set screw and I just need to
rotate that probably just a little bit so it doesn't catch. So I decided to buy these special
pliers I'm using here just to get these e-clips off. It made the job pretty easy. You barely have
to squeeze and lift up and the clips come right out. This clip seems to be a little bit different
than the other two I just removed and this tool is having a hard time grabbing a hold of it because
they're so thin. I can't seem to get the center wheel and the first wheel on the strike side to
come off. So I'll have to flip the movement over and see if there's something else holding them on.
Oops! I think I squeezed too hard there and that went flying across the room. But I was able to
find it. I heard it hit a few things and was able to track it down. So I just noticed that this cuckoo
is missing an eye and I'm not sure how that happened. They're painted on and I think I'll go
ahead and leave it like that because it gives that cuckoo a little more character I think.
So it looks like the strike gathering pallet is holding the first wheel on and the half star cam
is holding the center wheel on. And I don't really know of a good way to get those off
and I didn't want to risk damaging anything so I figured I tore things down good enough to get
things cleaned. All right so now I can get everything in the ultrasonic cleaner and I
think I'm gonna have to get a bigger ultrasonic cleaner at some point because there's definitely
not a lot of room in here and I think it'd make the job a lot easier if I had a bigger one.
So while that's running I'll go ahead and get everything else clean
that wouldn't fit. And so I'll first start using soapy water and then going over each pivot hole
with pegwood and then scrubbing everything and making sure I get all the dirt and the grime off.
Looks like the water is pretty dirty so that took off quite a bit.
And then I'll finish things off with the mineral spirits
and that gets all the grease and oily deposits off. All right so now I can get everything
back together and oiled and see how it runs. So I got a little nervous using those other
pliers to put these clips back on because I didn't want them to ping across the room so
decided to use these pliers to clip them back on and I didn't have to use much force for them to
snap in but those probably aren't the right type of tool to use for that but I wasn't sure what
else to do. So there's one thing in particular I'm not addressing on this clock and that's any
worn pivots or pivot holes and that's simply because I don't have those tools yet. This is
only the third clock I've worked on and I just can't go out and buy hundreds or perhaps even
thousands of dollars worth of clock making gear when I'm just starting out. But I plan on getting
those tools at some point and learning those skills but I didn't do that for this clock.
Now we can get the the top plate back on and this part can take quite a while because you have to
line up all the pivots with their pivot holes and it can be quite tedious so I usually just
start in a particular corner and then get that set, loosely put on the nut and then work my way through.
Man this spring was hard to get back on. You have to put it through the hole, wrap it around the
plate and then pinch it back up on itself.
On my last video there were comments made that I shouldn't have been using three-in-one
oil to oil the pivots so I went ahead and bought some real clock oil
and we'll see how this thing works. I was also greasing the the gears and the pinions
with lithium grease and apparently that's a big no-no so I stopped doing that and I'm not doing
that from now on so I really appreciate the the comments and the feedback that you guys
leave in the comments and that just helps me get better and better each time. I decided to use a
paper clip for the missing hook on the cuckoo door. It already seemed to have the right bend to it
so I just have to cut that down to size and get it glued in.
So it looks like I can't tighten up this one because the screw's covered by the case
so you want to see some magic? Looks like someone's put a nail through the front of this case.
I'm not sure what they were thinking but I'll go ahead and back that out. So I thought I would
be able to get the cuckoo in from the inside of the case but I had to take the cuckoo off
and bring him in through the front. I just couldn't get him hooked onto the door quite right
so I made this part just a little bit more difficult because there's not a lot of room to
fit my hands in there. But I was able to get it and now we can get the bellows back in.
So now we can see how the cuckoo sounds with a fixed bellow. I think I'm starting to go a little
cuckoo. So I'm going to go ahead and get this case cleaned up and I'm just going to use water.
I started using a q-tip but the q-tip fibers kept catching on the wood
and so I eventually changed to a small paintbrush and that seemed to make things a lot easier.
So it looks like it says Germany right there so that's pretty neat. I think I've seen some
clocks where it says made in Germany but this one just said Germany. So I went over this whole clock
all its nooks and crannies probably about three times just to remove all the dirt
and dust and everything that was on it. So I just brushed it with water and then when my water got
too dirty I would dump it out put fresh water back in and then go over it again until everything
looks clean. There's a little bit of rust on this washer so I decided to go ahead and knock a little
bit of that off. I wasn't trying to polish anything up here I just wanted to make it look a little bit
better and I think it did the trick. Now it's time to do a little bit of surgery on the deer
so go ahead and use some super glue and get that glued back on and I glued my fingers together.
I seem to always do that when I'm using super glue. All right so we can go and get the hands back on.
I wasn't quite sure where to put the hour hand just yet. I first want to listen to how many
times it cuckoos and then that'll let me know where the hour hand should be.
When you set the time on the clock you never want to move the hour hand you want to move the minute
hand. So in order to get the hour hand in the right spot I'll loosen the hour hand by pulling
up on it and it's just pressure fit and then I'll rotate it to the correct hour and then push it
back down.
So it cuckooed 10 times not 9 times at 9 o'clock and then 11 times at 10 o'clock
and then 12 times at 11 and 12 times again at 12 o'clock and then the problem corrected itself.
So I think I did something wrong when I was putting the movement back together so I'll
have to take it all the way back out and see if I can make a small adjustment.
So what I had to do was rotate the snail clockwise by one tooth that way when the
rack falls it hits the snail in the right spot and that seemed to fix the problem.
I went ahead and also checked each hour and I didn't see that issue come up again so I think
having that snail in the right spot would fix the problem.
And there we go a cuckoo clock from the 1950s ticking and cuckooing again.
I really appreciate you taking the time to watch and I'll see you next time. Thanks!
