How to Replace Tailgate Handle & Bezel 99-06 GMC Sierra

Auto Retech
2 followers
Brought to you by www.1AAuto.com, your source for quality replacement parts and the best
service on the Internet.
Hi, I'm Mike Green.
I'm one of the owners of 1A Auto.
I want to help you save time and money repairing and maintaining your vehicle.
I'm going to use my 20 plus years experience restoring and repairing cars and trucks like
this to show you the correct way to install parts from 1AAuto.com.
The right parts installed correctly.
That's going to save you time and money.
Thank you and enjoy the video.
In this video, we'll be doing a tailgate handle on a 2004 GMC Sierra, same as any 99-06 Sierra
Silverado.
The only tools needed are a half inch wrench and an X-Acto knife if you have a Rhino liner
in your truck.
Also, if you're going to order the tailgate handle, we do recommend ordering the bezel
as it's kind of difficult to get off without breaking it.
Actually, we found on our truck it had already been broken.
Just save you a little time.
To remove your tailgate handle, the first thing you want to do is remove this bezel.
Basically, there's two pins that go down and then it clips in.
You want to push down on top and then pull out.
This is interesting.
This truck is already damaged and somebody used two-sided tape to put it in there.
Let's see a close-up.
The tabs are broken off and that's what commonly happens.
Two-sided tape is all right for a while.
The problem is what happens is these trucks, the dirt just kind of swirls up and around
here.
Sooner or later, that two-sided tape is just going to let go and the thing is going to
fall off.
It's going to look like that.
Here on the tailgate, you've got three bolts.
You can see one is already loose because I was experimenting a little bit.
This truck's got a Rhino liner in it and a lot of trucks do now.
If you don't, obviously, you can just take these bolts off.
If you do have a Rhino liner, you want to use a knife and you just basically want to
cut very carefully, obviously, so don't cut your fingers off, but cut each hex.
I'm trying to do this fairly quick because if you don't cut this off, you won't be able
to get your wrench on there.
You can probably force your wrench on there, but this is the best way not to ruin your
bolts.
You just kind of back it in there and peel it off.
You don't have to get it all off.
It doesn't have to be perfect, but you definitely need to get enough off so that you can get
your wrench on there.
It's a half inch, really push down, and the bolt comes up and out.
You want to remove these three bolts.
Now, as I was taking these out, I wasn't filming because you don't really need to see me tear
them out.
Something funny, it has washers and the Rhino liners actually trap the washers in there,
but that's okay.
You can just remove it to that point and you'll still be able to remove your handle.
You just back it out.
You can hear my handle just drop down there.
I'm going to put our bolts on our 1A Auto magnetic tray.
Here's your handle.
There are two rods right here held in by clips.
Basically, I just broke that clip.
You just need to move these clips down.
The rod pulls out, the rod pulls out, and then there's your tailgate handle.
New handle.
See, it's all basically the same as the old handle.
What you want to do always is lubricate any points where it might pivot.
Spray them with a bunch of stuff.
Attach.
See, it goes that way.
Push them in.
Rods into the clips easily.
Just going to work it in a little bit.
Open up the tailgate.
Basically, do it one side at a time.
Grab the rod.
Push on your tailgate.
Grab this rod.
Push on the tailgate and it will open up.
Down here, we'll take the handle and you can line it up by my wrench here.
These washers are stuck in here.
It's a bit with no problem.
Looks like it is.
Last one here.
As far as tightening, it doesn't have to be incredibly tight.
I'm just going to hold them with my fist and that's good.
We have our new bezel here.
There's the old one.
You can see these are the teeth that are broken off.
You can see I've removed some of this two-sided tape because it needs a bite underneath the
metal and that will just get in the way.
Basically, this just goes in.
Push down on it and there you go.
All set.
This video was brought to you by www.1AAuto.com.
We hope we helped you out.
We are your source for quality replacement parts and the best service on the internet.
Feel free to call us toll-free, 888-844-3393.
We're here for you on the internet and in person.
Thank you very much.
