We did a custom installation of Renogy LiFePO4 (lithium) batteries in our travel trailer to upgrade our battery system, and we will show you how.
We'd had many instances where our old lead acid battery just wasn't up to the job. It even resulted in a dead battery that we had to jump from our truck battery once!
With this upgrade, we'll be able to boondock for much longer periods without having to use our generator. And it opens the door to our next upgrade: Solar panels! (Stay tuned)
Today we're going to show you how we did a custom installation of lithium batteries
in our travel trailer. Stand by for tips and tricks.
As we showed you in the previous video, we found a place for the batteries where they
won't take up any of our storage space and we won't have to drill through the floor.
The only downside is accessibility. It's a bit of a tight spot,
so we first need to build some custom shelving.
Today I'm here in our garage because we're almost at the point where we're going to
install all this new electronic stuff into the trailer.
But first I need to build a couple support structures to actually hold everything in place.
You know what they say, measure once, cut twice. That's not what they say.
I need this platform to take the least space possible, so I'm measuring just exact the
battery. I'm going to have little sides coming up here to hold them in this way,
and then I'm going to have these things here that I can put this tie down across
and hold it in the other way and hold them down when we're going over big bumps.
All right, we're ready to make the first cut. Safety first.
Well here it is, our battery shelf. This is what's hopefully going to put the batteries
in that tight little spot underneath our stove. So now I've just got to go and see
if that actually matches up. So Mel and I just went out to the trailer and I'll tell you,
we had a heck of a time trying to get them in that little spot.
But we figured it out and we have confirmed 100% that everything fits. Perfect.
So one thing we did notice was that sliding the batteries onto the shelf was difficult. So
I don't know if you can see here, but we put tape all along the top to make it nice and smooth,
make it easier for us to slide the batteries in and out. I've got all the feet exactly measured
out. Yeah, we're good to put this in a little bit more permanently now. We also want to be
able to monitor our power usage, keep the electronics cool and have a convenient spot
we get to the tricky part, installation. I had a little bit of trouble trying to get
the shelf above the drawer and I was telling Mel about it and she thinks she might be able to get
it. So let's see. All right. So what's your strategy here? I don't have one. Just do it.
I like that strategy.
Wow. Look at that.
Well, it's a good thing we had Mel available because now I don't have to trim it like I
thought I would. So Mel helped get the inverter shelf in place and now I just need to level it
off a little bit and get the inverter up to the exact height that it'll match on the front panel.
I've got these little riser blocks and they're just going to go right here and level out the
And then these larger riser blocks are going to go under the inverter and raise it to the exact
height. Fingers crossed. So I'm in the trailer. It's nighttime. I've got no light and no heat
because I've got the converter all ripped out. We're going to take this battery shelf and get
it down into these depths here. And then we're going to put these batteries on top of it.
I've measured it all out, but as we've seen already,
you're never 100% sure until you actually start hooking stuff up.
Okay, that's step one. So now it's time to install the batteries. And you'll see I've
attached the wires already because there's just so little room in there. Normally these wires
hanging around would make me pretty nervous, except these are what's called smart batteries.
And this little plug here, I've actually put them into shelf mode, which means they won't give any
current. So even if I cross these wires or, you know, touched up against the ground or something,
no problem. Confident that my batteries are still in shelf mode. Very little room to go in here.
The project's coming along very nicely. I've got the charge controller all set up here. I've got,
all the wiring roughed in, fuses. I just have to make two more wires and hook them up and
should be in business. Oh, look at that. There's my monitor. 13.3 volts. Now let's see if we're
hooked up to the trailer correctly. Hey, hey. Did it just get a little brighter in here?
Apparently those lights take about 1.2 amps. You can probably hear the whine of the converter fan
here. Everything appears to be working. The battery is charging at a rate of about 45 amps,
which isn't bad. Converter's going. Trailer has power. Not bad.
It's 11 p.m. The converter is all back in place. Everything is all secured and hooked up. This job
didn't actually take as long as I thought, but there was two sort of minor what could have been
disasters, I'll say. One is when I turned on the converter for the first time. I got a spark
and that scared the crap out of me, so I immediately turned it off, texted my brother,
told him what happened. He walked me through the whole circuit, checking for things that might be
shorted. It looked okay, so turned it on again. It sparked a little bit again. Apparently that's
just what can happen. We just never saw it or heard it before because it was behind this panel.
I don't know. If you know something about this, please let me know in the comments.
So the second thing was, all right, we've got battery hooked up, everything's working great,
except the slide is not working and the tongue jack is not working. Why are they not working?
So again, I had to consult my brother, who's a bit of an electronics expert. We're going through
the whole circuit, we're tracing everything, we're checking voltages at certain spots.
At one point I'm like, okay, well the wire now just goes down through a hole in the trailer,
so I don't really know exactly where it goes from there. He's like, okay, well it probably
goes to some kind of bus, you know, there's probably a fuse or something, and immediately
a light goes off in my head. Three days ago when I started this project, I pulled the external
emergency battery cut off. Do you think that I had turned that back on again? No. Duh. It's
pouring rain outside. I've got to go out, go around, push in the disconnect, come back in,
turn everything on. It all works perfectly. So thank you to my brother who talked me through
it all and reminded me that I had not turned it back on. What a fail. But these are the kind of
things that you learn as you do a project like this. It's just those little things that you
forget, right? All is well, all is good. We've got a brand new battery system and we're going to be
able to boondock a lot longer than we were able to before. So far, so good. Stay with the channel
as we upgrade further, including installing solar panels and a high amperage truck charging cable.
And we are always very thankful when you take the time to like, subscribe, and turn on
notifications. It helps us reach more viewers just like you. Thank you. And in the meantime,
keep on living the life you've imagined. So had a little bit of trouble trying to get the drawer.
Oh, wait. So we're coming along here with the inverter shelf. Yeah, I can see my breath a
little bit.