PORSCHE 911 | How It's Made: Dream Cars

Process A-Z
9 followers
4 Video Views·Oct 10, 2024
Production begins with the body shell assembly where the chassis is made from mild steel and
aluminium. Production islands with weld and transfer robots put together the largest parts,
notably the base of the engine bay. The three robots are programmed to work on all variants
of the model. The quality of the spot welding is checked and after each weld is inspected
any necessary changes are made. The distance between the parts are also measured to certify
that there aren't any variations greater than a few micrometers. Once the inspection is completed
robots move the parts to another workstation. The car's body shell side panels move via a
conveyor lift to a welding station. The panels are loaded into the robot which then welds the
parts into place. Since the car chassis is a monocoque structure the side panels are attached
with the base already complete. Automated guides hold the panels in place while they're welded to
the base. The body shell assembly line delivers the doors and weld robots secure them by welding
the hinges to the body. However it's only temporary as the doors will be removed after the painting
process to be reattached on the vehicle assembly line. Other frame parts and the car's roof are
welded to the vehicle platform in this automated assembly section. Once complete a lift moves the
skeletal body to another station for treatment and inspection. Here the strength and quality of
the welds are inspected and verified. Afterwards the structure is taken by an overhead conveyor
lift to another assembly line for parts and cleaning. At this stage the bonnet is installed
and then the body is cleaned. Using special cleaning agents any construction dust along
the body surface is removed. The frame weighing 36 kilograms less than the previous generation
chassis is moved by a transfer lifter to the paint shop. The painting process begins by dipping the
body into a bath of cathodic dip primer. Cathodic paint enhances the corrosion resistance of the car's
structure. Next a high pressure shower rinses the frame to remove any excess paint before the frame
dips into the primer treatment again. The body shell is dipped into seven consecutive primer
baths ensuring it will be completely protected from rust and other environmental damage.
By flipping and returning the body into the bath this guarantees that the primer paint
reaches every cavity and corner. It also eliminates any streaks that might develop at the joints.
After the paint is cured in a 30 minute drying procedure the structure moves into another room.
Here robots under seal the seam with sealing paint which consists of a pvc coating. This
layer of protection waterproofs all the seals and helps prevent corrosion. In another paint room the
body receives a filler coating. Robots apply a base coat that aims to protect the body from stone chips.
The filler coating color is selected by the customer. The car receives eight layers of the
environmentally friendly water-based filler coating. Once that paint is cured the body shell
moves to another area where robots apply two solvent-based clear coats. Wearing protective
gloves to avoid any contact with the new paint the company's crest is then installed onto the bonnet
using a specially made clamp revealing a symbol of Stuttgart's pride. The production of the engine
begins with pre-selected engine components such as the crankcase, the crankshaft and pistons.
A rod connecting machine is used to assemble the piston rods to the piston heads. A leak-proof ring
surrounds each piston head then the combined unit is gently slid into the cylinder block of the
crankcase. Once all the pistons are set the cylinder block moves to a new workstation.
With the aid of a lifting device the crankshaft is lowered onto a work table.
Using lubricated clamps the connecting rods are installed and fastened to the crankshaft
using an air impact screwdriver. After securing the piston rods metal timing chains are added to
the crankshaft. Because it's too heavy to handle manually a mechanized lifter is used to lower the
crankshaft into the casing of the crankcase. After it's attached into position all moving parts are
checked to ensure they're working. As the two separate cases of the crankcase roll into a
containment room transfer robots raise one part onto the other. The two parts are aligned and
linked. The six pistons are now parallel to each other in two rows of three. The new engine block
is then moved onto a carrier called a cross member which transports the engine to other stations for
further assembly. At the next station a cylinder head gasket is installed onto the engine block
in between the two housing parts. The cylinder head section which houses the camshaft is then
fastened into place with an air impact wrench. Then the engine block is rotated and a second
cylinder head gasket is installed on the other end of the engine block. Next another large piece of
the engine block is lowered into place using a lifting device. Large bolts are then placed into
specific positions. Then the near complete engine is sent to another workstation for further parts.
