Washer F5 Error Code DIY Repair - Step By Step

Mastering Mayhem
12 followers
Washer F5 Error Code DIY Repair - Step By Step
DEWALT 20V MAX XR Impact Driver, Brushless, 1/4", 3-Speed, Bare Tool Only (DCF845B)
https://amzn.to/47VpRR9
Spec Ops Tools Slotted Screwdriver, 5/16" x 6", Magentic Tip, Cr-Mo Steel Shaft, 3% Donated to Veterans
https://amzn.to/3N8cdRk
LEXIVON Tamper Proof Torx Bit Set
https://amzn.to/3Yckqu9
#whirlpool #whirlpoolappliances #whirlpoolcabrio
All right, if you get this code, the F5 code
on your top loading Cabrio Whirlpool wash machine,
that means that your latch that keeps the door locked
is no longer functioning properly,
no longer working at all.
I'm gonna show you how to take out the old defective latch
and install the new one.
We paid about 80 something dollars in change,
almost a hundred bucks with tax.
That is the part number.
If that is the model number right there,
so you'll know if you have the exact same one
if you go off that model number.
The only tools you should need is a flat screwdriver,
a quarter inch hex nut driver, Phillips bit,
and a drill driver or impact driver just to make it faster.
Okay, of course, first thing you need to do is unplug it.
Start off here in the back.
First screw we're gonna remove is this quarter inch hex
to remove this cover right here, just like that.
Then we remove the other two quarter inch screws,
which is gonna be this one right here,
as well as that one right there.
So another quarter inch here.
So a quick recap, remove this cover,
which is just one screw right here,
and then this screw and that screw.
Slide the top forward just a little bit,
lift, and then we can open that top up.
You should be able to slide it forward and slide it back,
and you can lift it up.
Basically, you release the lid
from these two tabs right here.
Okay, this tab and this tab.
Before you lift this, you wanna take some masking tape,
electrical tape, any kind of tape really,
to tape down the door,
keep that top door from opening up on you.
Just tape it up with whatever kind of tape you may have.
So just like that.
Now we can get to the mechanism here.
Two Torx screws first, T15 Torx bit.
One down, there you go.
These are the two clips right here,
and here, pretty snug, but you just push it down
and forward.
So yep, there you go.
So now you can see it released the display panel.
It's the same thing on the left side,
but because we have this mechanism here,
I recommend you just use a screwdriver,
push it down to where it can release there as well.
You got that panel up off of the main surface here.
We have these metal tabs right here
that hold the cable in place.
You just open them up with a screwdriver
to take this cable out.
Just pop it out like that.
That hook right there.
So just use a screwdriver to open it up a little bit
so you can release that cable and you're good to go,
and then we'll be able to get to the other side there.
Okay, next step right here.
We gotta remove this screw here,
this screw here, right there,
one right there, yeah.
So one, two, three, and four.
Then we'll be able to lift the panel off.
So I'll show you that here in a second.
Right here, number two.
Should just be able to pop off here.
There we go, at some angle.
And you just have one cable here,
so you can actually just put the panel down
because it gives you a little bit of slack.
So this is the one you wanna disconnect.
The Pro's releases black zip tie clip here.
It's the last one before it goes through the hole here
on the other side.
It's this guy right here.
And I'm just gonna use my screwdriver.
I guess as long as you just force it down.
There you go.
There's a little tab right here, right,
or a little lip.
Just push that out,
and then you should be able to unplug it, just like that.
All right, so grab this guy,
just get it out, push it through the hole here,
and the old one is gone.
There we go.
That's it, we got the old one out.
That's the tab that just wouldn't come out anymore.
That's what locks the lid, right?
Otherwise you get that F5 error code.
Let's replace it.
It even comes with a new wire clip here,
so don't worry about the old one if you break it.
There is a new one on here.
Grab this end,
and we're gonna feed it through the hole here.
Just pop that clip in.
Now it's holding.
All right, so now we're on the panel side.
Yeah, okay.
Again, just kinda reverse the whole process, all right?
Should just snap in easily, all right?
Don't force it, but just listen for that click, okay?
Well, that's it.
Now we're plugged in.
We can put the cover back on.
I'm not gonna push everything back in
because I wanna make sure I can run the cable,
and just like we were saying,
you have these clips,
and they even have electrical tape.
You know, if you want,
you can use a screwdriver to open that clip up,
or you can just use your hands.
For me, I can basically open it up with my fingers,
and then it pops in, okay?
Just like that.
And one more up here.
There you go.
Zip tie clip, U-clip one,
U-clip two in the middle,
and then three at the top.
And now we're just gonna run the rest of the cable
right up in this channel,
and then use the two Torx screws
for that guy to be securely fastened back to the lid.
Basically, we just screw this on,
and then the cable just kinda falls
into this lip right here, this channel.
So if you're familiar with your drivers,
you can use that,
but others will recommend a hand screwdriver
to hand tighten these.
Again, I know how much,
I just do like one impact with my impact driver,
and we're pretty much done underneath.
Looks good.
I've never done this before.
This is my first time,
so for all you guys out there,
you know that it's your first time as well,
don't be afraid to do it, man.
We can remove the tape, just drop this down.
We'll just let it drop all the way down,
and then it slides back into place there, okay?
And then this display panel,
remember all it was,
those two spring tabs here,
so it should just pop back down.
Just like that, y'all.
Real simple.
Okay, and now we just screw all the screws back
in the back, right?
It was two here, one in the middle,
two on the side, and then the panel.
So I'll show you real quick
how we're gonna do the first two
that hold the top piece from sliding forward
so you can remove it.
Those are the two screws that keep this portion
from sliding forward, right?
Now we just got the remainder of the screws,
or is this one here,
that one here,
and that one right there.
There we go.
This is the final piece.
It goes right back here.
You got these two openings,
those tabs hook into, right?
All right, the last screw.
Everything is back on.
Panel, everything's good.
Let's plug the washer back in.
Let's just push this back in
where we usually have it.
There we go.
Let's just give it a whirl,
see if we get that F5 error code still.
Power it on.
Let's just do a quick wash.
Let's see.
Shoot, that's about 1050.
Oh, we got it.
There we go.
That would not show up anymore.
It's working fine.
I think we're good.
I think it's gonna start.
Yeah, there we go.
Oh yeah.
We're good.
No more F5 error.
Pretty easy.
I think it's better than paying someone else to do it.
It took me about an hour
because I was also recording,
but I think if you could just focus on it
and watch the video,
20, 30 minutes, you're done.
It's putting water in.
That's how we do it, y'all.
As always, follow for more tools, tech,
DIYs, and amazing deals.
