Restoration Hardware knock off / DIY industrial clock from cardbord and old newspapers!

Amazing Life Hacks & Craft
124 followers
Hi everyone and welcome to my channel. I'm Irina and today I'll show how I made
industrial clock out of cardboard and old newspapers.
The size of the dial of the clock is 8 inches.
I decided to make the dial 2 inches deep and I calculated the circumference of
the dial contour using the well-known formula.
It turned out 25 inches. I'm cutting out all the details of the
clock body from corrugated cardboard. It used to be a shoe box.
I didn't have enough cardboard so the strip will consist of two pieces here.
When cutting the strip pay attention to the direction of
corrugation on the cardboard. It is to be perpendicular to the strip.
Then it will be easy to shape it into a ring.
Take any tube shaped item like bottle, can,
anything cylindrical and with its help bend the strip.
I'm connecting the strip into a circle using masking tape.
Then I'm cutting out 12 details of the outer frame of the clock
from the same corrugated cardboard. As always,
a link to plates of all the details and the printable
of the dial in the info box below the video.
These details are also to be placed perpendicular to the direction of
corrugation on the cardboard. I'm cutting out
all the details. Then I'm bending these parts of the frame.
First, I did it over a tube like I did for a circle but then I realized it was
way easier and faster to do it just with my fingers
crushing each row of corrugation. After I've shaped all these details I'm
connecting them together. I'm also using masking tape here.
Then I'm taking some old newspapers. I'm tearing them into pieces until I get
some bigger pile and covering the cardboard base with
pieces of newspaper dipped into white glue. I'm not thinning
the glue so papier-mâché turns out to be really strong.
You are to apply quite a lot of layers. I didn't count exactly how many I got
but not less than six. I'm drying each layer before making the other one
because if you apply all layers at once they'll get dry
forever. I helped it dry faster with a hair dryer a little.
And I'm covering both the inside and outside
of the base. After drying this frame is really strong
like made of wood. The outer frame of the original clock I'm inspired by
consists of four details. So here I'm making the second set of
details just a tiny bit larger than the first
ones. In order to match both frames I attached
these outer details to the first frame using masking tape and
only after that connected the seams. I'm covering the outer frame details
assembled this way with several layers of newspaper
not touching the edges and seams between
four resulting details. After drying the outer four pieces already hold their
shape well so I'm detaching them from inner frame.
I'm trimming the edges a little to make the seams a little wider
and after that I'm covering the edges with newspapers.
I'm not making these details very thick. I already began painting the inner frame
when I realized that I hadn't made a second ring to attach the frame to the
dial. So I'm taking another strip of
corrugated cardboard also two inch wide. I'm making a circle to fit the frame.
I'm measuring it to place so there's no exact size. I just try it
over the frame to fit tightly. And I'm also covering it with newspapers
to make it rigid. After the base has dried to make the
surface smoother I'm taking wood putty and applying it
in very thin layer. I'm using plastic spatula.
It's soft and follows the doughnuts relief
really well. If you're new I want to say a big welcome and would love you to join
my community by tapping on the subscribe button
as well as the bell to keep up to date with everything I have to show.
After the putty has dried I'm sanding the surface to make it
really smooth. Time to paint. I'm painting the inner frame along the
edges and seams only where it will be showing from under the
upper details. I'm painting the dial ring from outside
and partly from the inside with black acrylic.
After the paint has dried I'm dry brushing the frame with silver
paint to create an aged metal effect. I'm priming the outer details with white
glue to make it even more strong. Then I repeat the
steps I did for the ring. Painting with black acrylic and dry
brushing with silver. By the way I was thinking over for
quite some time what to use for the clock frame. First I
wanted to take a suitable bow and sew off the sides. Then to cut it out
of wood but everything looked really complicated
until I thought I could try to make the frame
using the papier-mâché technique. When my son was a little boy I used this
technique to make cardboard swords for children for some
holiday party and starting a wooden ruling side as a
central rod. These swords survived the party and then
many months of games and I think we still have one of these
somewhere in his gun storage box. So you can be quite sure the material is
really strong. The main thing is to make it quite
thick. I'm cutting the dial for the clock from thin plywood.
I had a leftover box of chocolates, found it
when decluttering the pantry and decided to use it.
You can also buy a ready-made circle of thin plywood
or glue several layers of thick cardboard together.
I'm priming the dial. I'm sorry it looks that I didn't wash my brush well.
And then I'm painting it in ivory. Here I mixed white,
dark ivory and a dash of black. Since the clock is vintage I'm using a
sponge and lightly touching the edges and surface of the dial with brown paint.
Then I'm taking a printout of the dial, combining the centers of the picture and
the base and pinning it together. Then I'm wetting
the paper with nail polish remover or better with acetone and pressing it
firmly. You can even rub it with some plastic
card or spatula. For large pictures, as in this case, best
is to work in sections so that ink transfers better from paper
to the surface of the dial. Please note this will work with
laser printout only. Inkjet will bleed too much.
Take off the paper and here is the most vintage
dial ever. If anywhere the paper has passed along with the paint you can
gently roll it up with a damp finger.
Finally, I'm applying varnish to seal the dial and covering
all the other painted parts with matte varnish.
To attach the dial to the ring I'm putting measuring tape on the inside of
the ring and making nodes around the entire circumference in
order to align the dial. Then I'm inserting the dial into the
ring, coordinating the marks and hot gluing it to place.
The original clock has round pyramids made of
rings around the entire circumference. I decided to make mine from washes from a
hardware store. I took six sizes of washes. The biggest
one 20 millimeters, the smallest six
millimeters. I'm connecting the washes using super
glue. You can also take gorilla glue. They turned out to be quite weighty and
make the clock really nice and heavy. I'm also hot
gluing all the pyramids from the inside for
extra secure. For some reason I trust my hot glue
more than super glue. The resulting pyramids are to be
I'm dividing the circle into equal parts with the measuring tape
and outlining the places for installation of the pyramids.
I'm applying a couple of drops of glue over the pyramid
foot and put it to place. To make even gaps between the pyramids
I'm using a small strip of paper of the required width as a template.
The four external details will get some rivets along the
seams and I'm marking where I'm gonna put them.
I'm making a paper template of the quarter of the donut,
make markings, cutting it out and poking it with a thick needle.
And here I got a template for marking the inner contour.
I just put the paper over the detail and drawing dots
in the punctured holes. According to the markings along the seams I'm attaching
brads. I'm poking the seams along the markings
with a thick needle. This is why I didn't make these details
too thick. And then I'm attaching brads. I have here
very cheap ones from AliExpress. You can also
fake rivets by gluing halves of piece, putting hot glue dots and so on. But with
brads it's very neat and I like their look
most of all. Then I'm connecting all the details of
the clock together. First I'm twisting a screw into the
tops of all the pyramids and unscrewing it back to mark the
holes in the ring where I'll twist screws from the inside
to get into that pyramids. Then I'm twisting the screws from the
inside so that the very tip of the screw will
show from the top of the pyramid. Here I'm already using a screwdriver.
I'm attaching the outer frame face down and tighten the screws
until the tips show from the other side of the frame.
I'm leaving the heads sticking out a little. I was afraid to ruin the base
if I twisted it too tightly. And I'm covering the sharp tips of the
screws as well as the caps with hot glue.
Then I'm attaching the outer details. I'm covering the entire
surface except for the edges with white glue
and applying some hot glue to the edges to connect
everything tightly. I'm also applying some upholstery
tags along the markings around the dial. To make it easier to hammer you can
first poke holes in the base with a thick needle.
From the inside I'm also covering the sharp tips of the tags with hot glue.
And I'm painting the entire underside black.
If desired you can also make a flat back cover for the underside
then all these tips of tags and screws will not be visible at all.
It remains to install the mechanism. I edged the arrows a little with black and
brown acrylic using sponge. I'm drilling a hole for the clock axis
and I'm attaching the mechanism, the arrows and of course
inserting the battery. I'm very happy with the result. I got
exactly the same clock as seen on the picture I was inspired by.
I love this style. I'm a big fan of everything
old and worn. I think the clock is really classy
and of course its cost is very pleasant. It's made actually of nothing. I had to
buy only the clock mechanism and washers. The rest I had on hand. I haven't yet
decided where to hang the clock. Hope someday we'll have a workshop and
I'll be able to hang it there. Let me know what you think of the
project down below. I want to thank all of you for joining me today.
Have a great day! We'll see you in the next one.
Bye!
