How to make Mountain Range Rings

Native American Crafts
28 followers
2 Video Views·Sep 24, 2024
How to make Mountain Range Rings
So in this video I'll be showing you how to make rings just like these that have mountain ranges
on them. And this is not just on top of the metal, it actually goes all the way through
so you can see it on the inside. So let's get started. So the first thing you're going to
need to do is figure out what ring size you're making. And I'm going to be making a size 8 for
this. So I'm just going to take my mandrel and my calipers and measure that out. So it's about 18
millimeters. So the next thing you're going to need is your metals. And these are about 0.6
millimeters depending on where you measure from. And I'm going to be using the same size
for this ring. So you can use one of them in a size a little bit larger so you can get effects
like this where you have an actual little cliff in there and a layer. And you could switch this
to either side depending on how you round your ring. So now we need to figure out how long we
need our pieces of metal so we can make the proper size ring. So I'm going to take the 18 millimeters
and then add the 0.6. And this will make the ring a little bit too small but because we're going to
be hammering it and these are thinner metals it will stretch to the right size or you can stretch
it up to the right size at least. And then we're going to multiply this by 3.14. So this is how
much we're going to need. So just take your calipers and set them to whatever that happens
to come out to. If you're a little over like this it's totally fine. So now you need to mark your
metal. I'm just going to use my calipers to do that. If you're using expensive calipers or using
metals that are really hard don't use your calipers to mark stuff but these are very cheap calipers
and I do this all the time and they've been fine so far. So now that we have that line I'm going to
also mark it on this sheet. All right so now that both of them are marked like that I'm going to
make the eight millimeter mark on them and you do it basically the same exact way.
All right so now I'm going to cut it out using a jeweler's saw and I'm making sure to use one that
is pretty much flush because I have a bunch of them that have anvils that stick up. If you're
bigger material like this you really can't do it because it hits it so if you do have one of those
I do suggest getting one that has a flat surface like this. Anyways I'm going to cut the small line
first and then I'll cut out the entire length. If you don't cut this 100 perfect it's totally fine
just try to stay on the outside of it because if you make it all wavy on the outside you can at
least cut this down to be flat. If you get into here then you have to cut into your material to
flatten it out so if you do mess up mess up on this side. All right so that is our silver one
done now we need to do the same thing with our copper. All right there we go we have both of
our pieces now and if you don't want to work with silver for this if it's say your first time doing
this and you're worried about cutting straight lines and all that stuff just use some copper
and brass just like the rings in the beginning and then you can work with those are a lot cheaper
if you make mistakes and you can learn off of those a lot easier than going through and worrying
about silver. Just so it takes a little bit of stress out of this because I know cutting straight
lines is a skill that you have to actually work on but anyways with that said let's get to the
next part. So once you cut these out they're going to have a little bit of a burr on where you cut
I'm just going to take my file and just go over to take it down nothing too crazy
you can even sand this real quick and it would take it all down. All right so we have those both
deburred and we can move on to our next step which is a kind of weird one we're going to super glue
these two together. So I'm going to use some medium super glue any thickness will work fine
any color doesn't really matter because we're going to burn all this off but I'm just going
to put a couple of drops on here also if you're looking for this type of glue for inlays or
anything like that or even this you can get some from Starbond and use my code GOMEOCREATIONS
and you get 10% off and I believe it's free shipping too so just take this and put it over
the top and do not glue your fingers together. So once I have it overlaid like that I'm going to
take something heavy like another bench vise and put it on top of it just to make sure everything
is flat and stuck together and when doing this be sure that they don't slide because even though
it is super glue when it's wet it is actually slippery. So I'm just going to spray an accelerator
on this to make sure everything's hardened so I don't risk getting my fingers stuck. So here we
are both pieces are glued together it looks like it slipped just a tiny bit on the edges so you
can see on both sides it kind of moved but I made these a little bit bigger than they needed to be
when I cut them so I can file that off and everything will still be fine and because
this is a thinner metal it'll stretch to the right size anyways. To do that I'm going to be using a
miter block and what this does is it makes it really easy to make perfectly flat edges. All you
do is you stick your metal inside of it and clamp it down with just a little bit of it exposed
and then tighten these up and you can take off little areas like that and make them completely
flush. So I'm going to do that on both sides you can see how close that gets and I can't even feel
it now so I'm just going to flip it over and do the other side and then we can move on to actually
putting a pattern on this. All right now that we have this and it's all cleaned up and technically
it'd be ready to go it needs a pattern on it so there's a couple ways you can put patterns on
this stuff. How I like to do it is designing stuff like this so I can just print it out
and have it on a sticky label paper and just stick it onto my stuff and I don't have to worry about
having to draw something perfectly and I can basically repeat doing these patterns over and
over again if I needed to. You can also just scribe in and draw on here. You can use a pen,
you can use pencil, you can use a little sharp piece of metal to scratch it in place so it can't rub off,
a bunch of different things. So I like to design a lot of my stuff on the computer and I know a lot
of you don't know how to do this. Well this is the perfect time for this video's sponsor. So this
video is actually sponsored by Skillshare and I thought it'd be a fitting sponsor for this channel
because you're looking to learn and Skillshare is an online community that allows you to learn at
your own pace and every class is working towards a goal to make real projects not just fundamental
learning. It's we're going to be making something. That being said I'm actually taking a class right
now from Jordy Van Putt on how to edit better using Adobe Premiere Pro which is what I edit all
my videos in and make them better for you guys. And for these patterns I suggest Inkscape for
Beginners by Gaia Manfort. This is a free program that you can download and design this kind of
stuff and you don't have to pay anything for the actual program and you can make awesome patterns
like I do. There's also a bunch of other classes on there including jewelry making classes and you
might even find one from me on there. So Skillshare is giving the first 500 people that use the link
in my description or in the pinned comment of this video two free months of Skillshare Premium.
It'll give you access to their large catalog of all types of different classes so you can check
out everything that Skillshare has to offer and then after your two months Skillshare is as low
as $10 a month with an annual subscription. So thank you Skillshare for sponsoring this video
and supporting my channel. So with all that being said let's get back to these patterns. I'm going
to be using this one right here that goes all the way across because I want a ring that has a
connecting pattern that goes all the way around it. So to use these I'm just going to cut them
out with some scissors. I'll also have these patterns in the description so you can download
them for yourself. So when using the paper that I use, the label paper, make sure you cut and have
a grip point for peeling like this because if you just cut this off it's really hard to actually
get this to unpeel. So what I like to do is peel it off and then cut it afterwards. I've also
already measured these to the right size for a size 8 ring. So it doesn't really matter what
side you put this on but I do need to cut this a little bit closer on at least one of the edges.
All right so you just want to line up the corners. This is going to be very finicky on camera.
There we go. For this top edge instead of cutting it down I'm just going to fold it over just to
get it out of my way. So now we get to do the fun part and cutting all this out with a saw.
So we're just going to start with one side and start our line which is probably going to be
what the hardest part of this because you also don't want to pick up your pattern and then you
just kind of want to follow your line all the way. When doing this you can't do any backups.
If you mess up just go with the flow of everything and make it work. If it's a mountain thing like
this you can just add an extra bump. All right here we go. It's all cut out and as you can see
right here I didn't like that little spot that I designed so I just cut through it and just kept
the mountain how it is. So now we need to heat this up with a torch and burn everything off of
it and burn the glue. Make sure you have a well-ventilated area when burning this stuff off.
Okay so I have them both on the screen. I'm going to need some tweezers to make sure to grab them.
So I'm just going to use this torch for burning everything off. All right that should be good
enough. So I just take these and throw them into some water and then pickle them. All right so here
they are all cleaned up and you'll notice and you probably have already guessed this
they are mirror images now and all you need to do is swap these two pieces and you have exactly
what you need to make that ring. So from one of these rings you can make two. They'll just be
opposite colors and all we need to do is solder these in place using some hard solder. So I like
using a charcoal block like this because it's a large flat surface and it is really easy to
solder on. So what I'm going to do on this is put some flux on it and then put our hard solder over
the gaps and heat it up. And if you want to know what flux or any of the tools I'm using really
I have links to everything in the description, a full list of everything I use if you want to
use anything that I use. All right so I'm just going to do one of these on camera
but I'll get both of them done. All right so it doesn't always fill in all these little gaps or
it'll bend up a little bit which is totally fine so just get it as good as you can and then put it
into your pickling solution clean it off and then re-solder the points that you missed. So if you
look right here it's missing some here and here and here so I just need to reflux this whole thing.
I'll probably place a couple pieces more solder on here and then everything should just flow
all together. All right so now that these are all cleaned up and soldered you can start folding
them around your mandrel and you can pick which side you want on the outside. As you can see this
is the side that I put all the solder on that I'm going to have to take off and this side is nice
and clean. So what I'm going to do is I'm going to bend this to be the inside. So when it comes
bending around the mandrel we actually don't need the right size right now so I'm going to use this
part because it's not graduated like this and it won't angle it weird. So just take your thumb and
put it here it should be really soft from all the heating we did. So you'll end up with them in these
u shapes and then we need to fold them a little bit more without making any kinks in them because
the kinks are really hard to get out once you get them. I'm using some pliers that have no teeth in
them either so it doesn't mar up this and leave marks. And then I'm just gonna push them by and
then snap it back like that and push down. This becomes easier with practice. So this is basically
how you want it. You want the joint to be completely flush. If it's not from when we already
cleaned everything up say if these little bits down here stick out a little bit just open it up
a bit and grind them down with a file. All right so I'm going to put a little bit of flux on here
right on the solder joint and then I'm going to take a tiny piece of solder and put it down here
and make sure my joint is directly on it. So there you go if you have a solder joint that
is completely sealed like that your solder will actually flow up. All right so here they are
out of the pickling solution after being soldered and they need to be formed into actually rings now.
To do that we're just going to use a mandrel and put it on the mandrel. What I like to do is push
down on it because it's a thinner metal. It'll bend for the most part but we're going to actually
have to hammer it using a rawhide mallet or a rubber mallet will work too. I'm going to flip
it over because this is tapered it's going to have a weird taper on it if you don't do this.
So I'm going to do that to both of these really quick and then clean up their insides because
they have a lot of solder leftover on the insides and then form them to their final sizing. So to
clean up the inside of this you can use some polishing wheels like these that are basically
rubber grits or you can use some of the radio ones that I have that I've used a bunch of.
So they're a lot smaller than they should be and they'll fit inside the ring. Normally they're
about this big when you first get them so used ones do come in handy after a while.
All right so there we go all the inside is cleaned up from the solder so there's no weird
bumps or anything in here. Still need to clean up the actual solder joint area but we're going
to stretch this out first and make it the right size. So we need it to be a size eight and right
now it is a seven and a half. So I'm just going to hammer it. All right so we need to clean up
the edges a little bit because they're not 100% perfect and they never are when you make rings
like this. So we're going to clean it up with some sandpaper and this is some 120 grit sandpaper
and I'm going to add a little bit of water to it and then just kind of sand in a circle or a figure
eight and just kind of all over the place until everything is nice and smooth. All right so there
we go the edges are all nice and cleaned up and even now so we're just going to clean up the
outside of them because there is a little bit of extra solder bits and we want a smooth surface.
I'm actually going to use some rougher bits on this so we'll leave some texture behind because
it looks better I think. So I'm just going to use the same 60 grit rotary bits to clean off
all the outside too and then I'm just going to work my way up through the different grits. So
this is 120 and then it'd be 220, 400, 600, and 1000. All right so that's as good as I'm going
to get it because I want it to have scratches and stuff to show more detail. You can fully
polish this if you really wanted to. You can see the inside has a nice brushed look to it.
So to get the look I'm going for I'm going to actually stain this black and I'm going to be
using black from Jack's Chemicals and because I'm dealing with chemicals I'm going to put gloves on.
I'm going to use a paintbrush to do this and I'm just going to brush it on. See it's slowly starting
to darken up everything. You can also dip this in the solution too. So I'm just going to let this
sit like this for a little bit and let it darken up. All right so here they both are now after
being rinsed off. This one I actually put the Jack's Chemicals Ultra Black onto it and didn't
let it stay on and dry all the way so it's splotchy on purpose. And then this is the blackener for the
copper, brass, and pewter so it shouldn't affect your silver at all. So I'm just going to dry all
the water off of them. So now I'm going to take a steel wire wheel and just go over it real quick
and I'm going to clean up the inside with these little scotch brite pads. And for this one I
actually don't like how it looks now so I'm just going to use this on the entire thing.
So here we go they're all done and we have two technically matching rings
that have opposite colors going on and the pattern goes all the way through into the inside.
And if you want more detail on your piece use two different sizes of metal like I did with these.
It's the same exact process besides you have a little bit more detail to it and things tend to
stick out a little bit more and when you add your patina to it it stays in all the cracks and
makes everything a little bit more pronounced. But it's up to you on how you want to do them.
Also over time these will all darken up and start to patina naturally. So that's about it. If you
found this video helpful leave a like. If you have any questions leave a comment I try to get back to
everyone. And if you want to see more videos like this one subscribe to my channel. I try to get out
videos every week. And if you want to help support my channel I have a Patreon and you can start
supporting as low as a dollar. So thank you for watching and I'll see you guys next time. Bye!
