How much water should I use on my clay? pottery lesson

Handicraft occupation
458 followers
#pottery #ceramic #lesson
Hey potters. I frequently get asked "How much water should I use when throwing?" by beginners. this isn't so much a question as it is people checking to see if they should use more of less water when they throw and especially center. So today we will be talking about how much water you should use hen you throw and in what situations you might find yourself using water in a different way. I hope you potters enjoy this potter lesson, good luck on your next project and i will see you potters next week :)
** My website ( where you can buy my work and frolic around)
https://www.earthnationceramics.com
** wanna send me food and make me fatter?
p.o box : 4540 florin road # E 138 Sacramento
zip:95823
name: Donte the potter
This right here is my favorite thing ever in the history of forever.
Hello you dirty potters. How are you today? Today I'm going to be answering a question that a lot
of you have been asking me in my social medias and that question is, how much water should I
be using when I throw? Usually this question is the result of two different types of people. Number
one, you're a beginner and you might have more of a mathematical brain. You might be thinking, okay,
x amount of water equals x amount of time on the wheel, right? Wrong. That is the wrong. Or you
might be centering and asking yourself, why is this getting dry as I'm throwing it? I put water
on it. How much water should I actually be using per amount of time? The second kind of person is
usually someone who's gotten past the centering phase and onto the beginner and sometimes even
the intermediate phases. There are people who have to control the distribution of their water instead
of just putting water on the clay body. While you're centering, there's pretty much only a ball
that you need to put water onto to make sure that your hands hydroplane over the clay causing a
little bit of friction so that you can control the actual product. But when you're getting up
into the cylinder stuff, things that are five, six inch cylinders or so, it's going to be a little
bit more difficult as you can't really just put water on the thing you're centering and call it
a day. It's a little bit more complicated than that. Unfortunately, the answer is different
depending on your needs for whatever you're throwing at any given time. And in today's video,
we're going to go over some of the examples and scenarios of how much water you would use
in certain situations or even at a base level. Let's start off with the most common of those two,
which is beginners and centering. If you're a true beginner and you haven't had much experience
centering your clay, my answer to you is pretty easy because I'm willing to bet a good 60% of you
are doing this. No, don't do it. Okay, this, this right here, grabbing your sponge and just squeezing
all the water on there at once before you center. See that? I need you to stop doing that immediately.
Now I got to clean up all the water mess I just made as an example. I didn't want to do that.
This is something that I see all of the time. And I do understand that for real beginners,
they seem to think more water equals more hydroplane, which equals less friction,
which equals more time with my clay. So I should just add more water when I'm throwing and that'll
fix all my issues, right? In fact, if you keep on adding that much water to your clay body,
you're going to end up oversaturating it, which makes it number one, way harder to work with when
you actually start pulling the cylinder. And number two can be a variable in causing S cracks in your
clay body. So before we go anywhere, I need you to stop getting your sponge, filling it with water
and just dousing your clay body with it as if it's going to help you. Not only does it not help you,
it actually harms your clay in the process. I mean, it doesn't really harm, harm the clay.
It just kind of like makes your life way more difficult for you actually. Okay, Dante. Well,
if I'm not supposed to do that, then how much water am I supposed to use? Are you ready for
this? It's actually a very simple fix. What I want you to do is put down your sponge. Don't use it.
Put your hands in the water buckets. Don't carry the water. Don't like grab some water. Just put
your hands in the water bucket, let them go and start centering. That's it. That's the entire
thing. It's not that hard. You don't need a sponge. You don't need anything like that. And if
you're coming up and down, you start feeling a little bit of friction and you notice a lot of
that water is going away. Here's what I want you to do. Hand in water. Don't carry it. Just bring
it to the clay body. And you'll see that it moistens the clay just as much as it needs to be
in order for your hands to hydroplane over the clay body and for you to control your clay. In fact,
I know I just told you to use two hands, but that's because I assume many of you are beginners.
Usually I just kind of leave this hand out here and I just use one hand, dip the hand in the water
bucket, touch my clay body, and it wets everything up. Nice. You can actually kind of see the water
disappear as I work. And if you start to feel too much friction and pull on your clay body,
you can very easily release slowly, dip one hand again and put it right back on and it re-wets it
for you. It's a very, very simple process when you're centering. There's no special technique
required. All you really have to do is wet one of your hands and you're good to go. As I said
before, if you really feel like you need more water, you can wet both of your hands. But usually
as you work with a clay body and you can kind of see the shimmer from my clay body go away over time,
it will start to dry out that water and spread it around and absorb into the clay body.
This will create more friction and when you feel too much friction and you let go, this one hand
will spread the water, and you can see it kind of get wet there, to the rest of your hands. You don't
really need two hands. Potter tip! This is something that I've addressed in previous beginner videos,
but I feel like I should just readdress this here and now. Usually as a beginner, you would want to
wet your clay body, right, using the one hand, and then when you start to feel friction, let's say
need to let go, you want to stop your wheel and then take your hands off, spin your wheel again,
and then re-wet and continue centering. This is for a couple of reasons. Someone like me probably
knows the timing in which they can take off their hand to get more water and then continue the job.
But if you're a beginner, many times you take your hands off while you're spinning the wheel
and something like this happens, where you don't really know the timing and you have to re-center
again. You have to do one of these. So if you're having a little bit of trouble continuing to
center while doing this, grabbing your water with your hand back and forth like this, I heavily
suggest you stop your wheel, grab some water, spin, and then continue. It'll help you miles and miles,
especially if something like this keeps happening to you. The second issue for most people who
progress past the point of centering is deciding how much water you need in what areas and where
to distribute water in order to get the maximum efficiency from your clay body without over
saturating the clay body itself. At this point, you probably already know how to throw a cylinder
like this. When you were centering, it was pretty easy. All you have to do was wet your hands, put
some water on the ball, make sure there's not too much friction, and then continue centering,
coning up and down, and sooner or later you'll get a hold of it. But once you get into the end of the
intermediate phases, you're going to have to start distributing your water in specific places.
This is where it gets a little bit tricky. After you pass the centering portion and you understand
that you need minimal water in order to center realistically, putting water on a ball while
you're centering or coning up and down, just carrying water over from dipping one hand in
there and putting it on the ball is no longer sufficient. Once you get to the end of your
beginner phase, you start to make good cylinders, you're going to have to start to think about the
distribution of your water and where it goes based on where you're going to touch that clay
body next. So if I decide to pull my cylinder one more time, this means I need to get my sponge
in order to distribute water and put it on the inside of my clay body as well as the outside
here, making sure the entire cylinder is wet so there's no friction while I end up pulling. This
means that your old water tricks when you were centering don't exactly work anymore. You can't
just get one hand, dip it, touch the clay body, and hope the entire thing is wet. You have to
make sure the inner and outer of the cylinder is wet so when you start to pull, you end up causing
less friction, more hydroplane effect, and you have more control over your clay body. Trust and
believe, if you start to pull without making sure this entire thing is wet on the inside and outside,
you're going to hit a dry spot and it's going to twist on you because of friction. At this stage,
you would actually have to put the water inside and outside of the cylinder. So you grab your
sponge full of water, put your hand right here, crux it a little bit, touching the inside of your
cylinder just like this, and you would end up squeezing your sponge down your hand and that,
in turn, will touch the inside of your cylinder. As long as you keep on spinning, it'll distribute
along the inside of the entire cylinder. You can do the same thing for the outside of your cylinder,
but it's much easier than the inside. You put your hand on one part here and you drip that water
down your hand. While moving your hand down the clay body, this will wet the entire cylinder.
This one does require a little bit more water because you now have a larger surface to put
water onto. Before, it was like this much clay, right? It wasn't that much. But now,
you essentially have to distribute this water among the outside and inside of your clay body
to make sure it touches all of the surface. Once the inside and outside are properly lubricated,
it's very easy to then pull. But trust and believe, if you do this without lubricating the inside and
outside with water, you will end up finding a dry spot and you will also find yourself
a twisty spot. You know, the not-the-not good place. A little trick here that has served me
very well for many years is I get my sponge, fill it full of water, I put my hand on the inside of
my thumb and the outside of my finger like this, making sure I'm touching with my thumb the inside
and the outside with this finger here, and I will drip all the water, while pointing downwards,
onto the hand itself. This will usually drip the water down my finger and my thumb and wet the
inside and outside of my cylinder simultaneously. Now I don't have to play this game of like,
playing the crab game of making a claw and putting a thing here and then making a cup of water hand
and then letting it go down the entire clay body. I don't have to do that. For years and years,
I've just been putting my thumb and my finger and dripping it down my hand and it takes care of the
entire process for me. And finally, once you get into the more advanced stages of ceramic artwork,
when you start to really throw bigger things, this here is probably already larger than six
inches but I'm talking about things that are 10 inches, some things that go up to your wrists or
your elbows even, this is the point in which you really want to start to get a little smarter with
the distribution of your water. At this point, you kind of need a sponge because the ability to put
your hand in and out of the cylinder is going to be a little bit rough. In some cases, whenever I
throw things that are about a foot and a half tall or maybe even two feet tall, I'm usually
standing as I form them. Because of this, there's a couple of tricks that really help with the
distribution of water, making sure that the inner and the outer of my cylinder is wet enough to make
sure my next pull is sufficient. For this, and I'm sure many advanced potters have already figured
this out, not only are you going to have to wet the inside of your cylinder as I showed you before,
making that little claw hand, you're also going to have to wet some portion of your wrist or your
arms. This makes sure that the dryness of your wrist and your arms, which are usually dry if
you're working clean, only your hands should usually be wet. This makes sure that they
hydroplane over your wrist, making sure that no friction is caused. So when you're throwing like
this, see, my wrist is wet. Now it's not pulling on my wrist. Now I can do a nice long pull. And
just as an example, I'm going to make a really quick cut, but there's three things I want you
keep track of here. Number one, whether I'm using my sponge to carry over a lot of water or not.
Number two, how much water I'm actually carrying over, whether I'm cupping my hand or not.
And number three, how many times I'm dipping my hands into this water bucket.
You see, it's really not that difficult. And the high majority of the time, it's less of a how much
water do I need to use in order to make X thing. And it's more of a, you don't really need as much
water as you thought you needed. You can get really far with probably about a third or even
half of the water that you've been using this entire time. Well, thank you dirty potters for
joining me today. I know this is kind of more of a beginner video. There's probably some more
advanced people watching this going, that's not how I do things, but everyone applies water to
their vessels and their centering a little bit differently. This is by no means the be all say
all end all video to what you should do with your water and how much you should use. It's really
just a guideline video for beginners and showing them different techniques of how to place their
water where they need it, when they need it to get the most effective and less soggy product.
You trust me. I know this from experience. If you work with it a little bit too long
and you're not getting any real results out of it, it gets, it gets floppy after a while.
I'm oversaturating my clay body just so I can show you how to not oversaturate your clay body.
And because of it, there's a mess everywhere. And it's, it's your fault. And I think you owe
me a like button. Well, thank you potters for joining me today. Hopefully this video helped
you out a little bit and learning how much water or how much water to not put on your product.
I imagine a lot of beginners are having issues with like, my stuff is getting really soggy and
I'm putting a lot of water on there and nothing's happening. And the clay dries out too quick.
I will say that there's a very small variable in the type of clay that you're using because
some clays are a little bit more water absorbent than others, especially if they have high ground
content. But even those clays don't need as much water as you probably think they need,
or at least they definitely don't need you to douse them with a sponge full of water every time.
One hand in your bucket to make sure that it's nice and moist and you lubricate your entire
cylinder or cone is plenty of work. I know it sounds perverted, but that is the terminology
and we got to deal with it. Hopefully this video helped some of you out discover how much water you
actually need on your cylinders and vessels in order to get that nice hydroplane effect.
You have a great time with your next art project and I will see you dirty potters next week.
Thank you for your patronage.
I'm oversaturating my clay body just so I can show you how to not oversaturate your clay body.
And because of it, there's a mess everywhere and it's your fault.
