Must-Watch: A Follower's Journey with His 1957 Oval Beetle Headliner Install

Chris Vallone
219 followers
11 Video Views·Sep 13, 2024
Doing good afternoon. I'm working on the VW bug
57 oval and
I'm doing the interior doing it myself. Just as I got my new steering wheel here. That's original steering wheel that I've got redone
All powder-coated it's original steering wheel from 57 that I got this peel and stick roof
I went ahead and put that just to help with the sound deadening. I put on the doors
I'm gonna be doing the headliner now. So the first thing I'm gonna do is
Just because well, the reason I'm gonna do my own headliner is because it's I just wanna when I'm done with the bug
I just want to know that I did this, you know, I would say 90% all myself
The inside the headliner the seat covers. I'm gonna do all myself
So we're gonna see how before the headliner goes up. I'm gonna put
This felt material and here it is right here
Here's a felt material that I'm gonna be putting up. I'm gonna cut probably around you see
36 inches for the door post. I'm gonna little 5-inch strips roll it up. I got this
spray glue here that
This so wind lace right here. I went ahead and bent them out because when you put the
the door
The b-pillar
The wind lace inside here. You want to make sure it's bent out and you're gonna get a little
I'm not here. That's for the sissy of its bar that
you know that I don't know why they call the same sissy bar about thing by motorcycle, but this is for the
The Oh Jesus bar right here when your passenger or somebody's holding on to their in the rear of the passenger
This wind lace here these grippers
Okay, these grippers here hold it together. All right, so let's go ahead and do it
I'm not gonna go all the way to the end because that's where the headliner goes on right on top of this
You got to glue it to this and make it all nice and flush
so
Let that dry for maybe
30 seconds or so or something like that. I already sprayed the the other felt that's gonna go right there
So it gives it a nice tight
As much as I could I'm gonna put this place it right here next to the grippers
Just like that
nice and easy
Don't want to snap so it's a little cushion here. So it looks when you get that
the headliner
Overlapping it. It looks nice
Window the oval measure the back of the window
And it's about 21 inches 21 inches from top to bottom
All right, actually, it's about 20, but I'm gonna give it about an inch
This felt can stretch a little bit so
A little bit bigger than 36. So what's about 36, but I said 37
So I give it a bit at a 37 and a half. So I give it inch and a half
But I went ahead and put this
We're gonna go ahead and spray this and you wipe this down
36 inches long
By four and a quarter, all right, let's do it
I'm gonna show you guys how to do it
All right. I got a clean edge here. I'm gonna put the clean edge above this this beam right here
all right this brace and then I'm gonna come over here and put it above the grippers because I don't I wanted to I
don't want to see these grippers and denton in my
in my
Headliner because like I mentioned earlier everything you do underneath just like bodywork if you have crappy bodywork
You're gonna get a crappy paint job. All right, even though the paint job looks good
you're gonna see all the imperfections in that paint the swirls and stuff like that and
So I'm spraying along here along this edge
My wife's laughing at me right now
Like I got imaginary friends
But I have no imaginary friends
Let's take a look. So we're putting this up
I'm starting here at the corner
You don't want to glue past this point, but if you do end up gluing past the point those guys that are watching
You know, you can probably put mineral spirits on here. Nothing harsh because you're gonna take off the shine of your bug
I'm not too much under here because it is not on you can take mineral spirits or
Maybe hot water you can WD-40 will work, but it's not the end of the world. All right
Initial stick look underneath if it's straight
It's right here a straight
Look underneath
And she is
And that's it
Then I'm gonna go ahead and go all the way to the front
All right, talk to you later
Here for the the beginning part of the headliner
so if you look
But basically here we are
Sir, well, you saw what I laid that felt down
I put an extra layer of felt so you don't really see see how it looks nice and soft out here
That's what you're doing. How I was doing it. Oh
Watch out what you do and it's her and it's around here
So I'll film the next window I do but this is what it is I
Heated it up with the heat guns. Give it a good little stretch got the vinyl soft. I got this material
And it's a good material stretches real good
Where the rubber oats and you lift it all the way up?
just like that and you
basically seal
Is there you don't glue on the felt you just glue on this this
the metal body
All the way down and that's it. You see how I did this one that I'm gonna do a little relief cut right here
It's all in here
I'm gonna massage it out a little bit
And that'd be it
And then got my clips cuz you got a clip. That's what I want. Just about right there. It's kind of heavy
Well, it is a tweed material man, I keep putting it up on them
Cuz I don't want to make them
I got a piece of steel here. Keep it. You see it's nice and tight. Don't worry about
Yeah, I got me a sharp brand new razor here. I'm on the outside of the car as you guys can see I'm going to
glue
Over here where we have to cut we have to cut along the side here enough to overlap this
And enough we want to cut enough. So I'm going to cut more towards the top
Not done here because I won't have enough. So if I cut here
I'll have more than enough to overlap it and more than enough to overlap the bottom
All right
measure twice cut once this
I'll say somewhere right here
Right now
All right guys all done with the oval in
The interior headliner in the back. All right. I got it all tucked in. I relieved the pressure over here
You see it
Lint this is gonna go in the grippers. I'll pull this up tight get that little wrinkle out
This goes in here. I see a little wrinkle, but I'll I'll get that out later
Okay, this is all tight. Let it blue set in all that's around
I'm gonna clean because you don't want to
Jack that mug up. It's wrinkled here, but I'll take this out put a little glue then and bring it up
You see how it comes out?
And you'll see the end product
It in there's gonna be a rubber
Seal here that goes here. It's gonna be putting this against this
Good afternoon. Another fabulous day working on the bug
Just taking my time doing the head like that soften up here in the Sun over here
I got an iron to it in a steamer
I got some of the wrinkles out but just put in the Sun put on the car get it nice and hot
Soften it up and it'll be all right
can you on the
headliner
All the way from the back to the front. All right
I think the grabbers that this goes into so we're gonna go ahead and put that in there and we hammer it in
This up just a hair
The little bows
On the thing
It's taking me a little bit because I have no time because I got the dojo at night and I got
My day job as well the transmission shop, but anyway
This is what what I'm doing glue along the edge
Just like just like this if you see the glue here
And if you get too much then you're just gonna get the WD-40 and take it out
All right, and then I just put a little bit on the headliner this part right here
Let it tack up the side as you guys already seen
Here and this this already set up and I left it a little bit higher so we can tuck it in so it looks all
uniform
Before I do this edge
You see pull it good go to the edge
I'm just gonna
On the outside of this you sell it straight that's how it was in the factory
All right post side. Okay. I don't want to contour the the bug
I just want it to go flat just like I'm doing the sides here
So as we're going down, it's gonna get tight as I go around the curve. That's why I bought my razor so I can
Put some relief cuts in there. Okay, don't pull it too tight. You don't have to yank on it
Meaning I'll see what I can do. All right
Okay, so I'm just gonna spray this nicely hardest part like I mentioned before is getting it around that but that's okay
Let's go for it
If I spray a little bit over here, I'm not sure it touches this it'll end up drying by tomorrow and it won't stick
And later I'm gonna cut that so I'm gonna look for the edge of the
Where the window goes I'm gonna cut find the edge and I'm gonna slice it right there the edge of the window
Matter of fact, I can do that, right?
Well, I'll wait and then I go to the inside of that edge on this because this is at an angle
All right, it goes at an angle. This is like a little pleat right here
All right, so it's a pleat that goes at an angle
Not too tight, but just pull it enough and if you mess up it's okay. You just do it again. It's this glue
Just so you guys know what I'm doing this is the inside of the fender well
I'm gonna cut all this then this is where the door panel goes inside here
So that's where you it wants to stick in the door panel. Not right here
All right
So now for where the outside of the window is
I go all the way up
to the edge
I'll be right here
And this one goes to the inside of the edge
And you get a little
Don't cut too much
Not sure if you guys can see it
Because it's gonna be at an angle
Let's go up here more about right here
Okay, I mean they didn't have this material stock back in 57 in the 50s this tweed
But I think it looks pretty good pretty vintage
Pretty old-school and it looks uniform
Need to put a I need to put a pleat in here
So I'll just cut it a hair
at a diagonally at
at a diagonal
And all I'm gonna do is just tuck it over and under so it looks like that
Perfect you see and this one's gonna go right here
Man
And if you cut too much take out some of this and lower it no big deal
All right, this one's just about me. I just tucked it in
The grippers here you see I just tucked it in real good
Got a little pressure on here just tuck the material in
Till there's like a valley. I know I put glue inside there. I
Put glue in there
And I'm gonna cut it right here all the way up. So it's a nice flush cut
Okay sticks out way too much. So I'm gonna put my knife in there and cut it
I'll show you on the other side what it's gonna look like. I
Do now I just made a little glue right there tuck that in
Right here, so it's a nice and even
Okay, I'm gonna cut just a little bit. I'm gonna tuck it right inside here. So everything is uniform
You see these wrinkles here. I need to get them out and how I'm gonna do that
I'm gonna get it out with a steamer
So I'm just gonna
Evening good evening
It's another day working on the bug, but now I'm finished
All right
Here we are right here. Let me just show you the end result of the headliner
the only thing I would have to do here is
Put the dome light in and that's it with the headliner. All right, the windows are gonna be
Put in next weekend got a buddy of mine gonna slap the windows in and also
Then I'll be doing the seats
But here we go
BAM
This is it right here. So let me put some light
Everything's all nicely tucked in as you guys can see
Everything's all tight
Looking over here
Got the bows
Got the shadow from my flashlight, but let me see if I'm gonna put that down got the bows on top. I
Do want to thank?
Also here I got the material from so fine I got the padding the headliner
From Chris
From classic VW bugs. I want to thank Chris. I couldn't have did it without his video
The the hardest part was this oval right here
I think the hardest part was the oval my hardest part would would be you know, but
But it's done so I want to thank Chris from VW
Classic VW bugs. It wasn't him for his video working step-by-step
Trying to you know, rewinding it put it together
Rewinding it just getting the fine detail
doing the first step second and you can't skip a step because you skip a step you're tearing everything all out and
So I know it's looking at a video you can learn a lot
But anyhow proud of how it came out really glad
