Flexible Pavement Design, Part 2, Modified Subgrade

Federal Aviation Administration
121 followers
Sep 9, 2024
Learn to create a flexible pavement design on a stabilized base and modified subgrade.
this video explains how to use farfield
2 to create a flexible payment design on
a stabilized base and modified subgrade
this video is part of the farfi pavment
design series by the Federal Aviation
Administration Office of
airports refer to advis you circular AC
150
53206 airport pavement design and
evaluation and AC 15053
35-5 standardized method of reporting
pavement strength PCR for the basis of
the design and evaluation procedures
implemented in
farfield in this video we will develop a
flexible payment design on a stabilized
base add a userdefined layer
representing a modified subgrade and
change the layer that farfield uses as
the design
layer step one name the job and section
let's open an existing job of farfield
videos and add a new section Flex mod
sub step two set the starting pavement
structure click the payment type drop-
down menu and select new
flexible this creates a starting
structure with four layers p41 H surface
P
41/43 hm stabilized p209 Crush aggregate
on a subgrade layer with a CBR of 10
step three edit the structure to reflect
site conditions in this example adjust
the subgrade CBR to five this would be
as reported in the project geotechnical
report based on Laboratory Testing see
chapter 2 of AC 150/5
532-6151
d6g appendix
H2 note you may have to create this
traffic mix in farfield and save the
traffic mix to file if you want to use
this traffic mix again 3,000 departures
of a Boeing 730 7800 with a gross taxi
weight of
174,00 lb 2,500 departures of an Airbus
a321-200 optional with a gross taxi
weight of
2714
lb 4,500 departures of an MBR 195 STD
with a gross taxi weight of
17,9
20116 and 3,500 departures of a crj700
aircraft with a gross taxi weight of
72,500 lb a stabilized base is required
if the traffic mix includes aircraft
that have a gross tax weight of greater
than 100,000
lb see
ac150 5320-wcp
under similar climatic conditions may be
substituted for stabilized based
material step five perform farfield
thickness analysis verify that the
analysis mode is set to thickness design
and then click the Run button the
analysis is complete once Firefield is
adjusted the structure to achieve a CDF
of
one in our example the recommended
structure is 4 in p401 h
surface 5 in p401 h stabilized 23 .3 in
p29 crush aggregate on a subgrade with a
CBR of
five a review of the traffic reveals
that the Airbus a321-200 is the most
demanding aircraft contributing 98% of
the damage generally in a flexible
analysis the heaviest aircraft with the
highest tire pressure will be one of the
most demanding aircraft on the pavement
structure step six adjust the structure
adding or deleting layers reflecting
materials available in sight conditions
the geotechnical report for the project
recommended using a 12-in layer of lime
treated subgrade laboratory tests have
shown this will result in a long-term
CBR of at least
25 to model this layer in farfield add a
userdefined layer beneath the p29 layer
by clicking the p29 layer in the image
view when the layer property box comes
up change the layer type to user defined
with a thickness of 12 in and a modulus
of
37,500 PSI this represents a CBR of 25
as recommended in the Geotech report
since farfield uses modulus e equal
1,500 * CBR enter the modulus value
using the same conversion
formula finally click add layer
below verify that the userdefined layer
is the layer above the subgrade and that
the thickness and modulus are
correct sometimes when adding or editing
layers in the farfield layer property
window farfield does not save all
information as expected if this occurs
click the new layer in the structure
window and modify the properties and
then save by clicking
okay in a flexible analysis farfield
selects the layer immediately above the
subgrid as the design layer as indicated
by the red arrow in the left column in
the grid view in a flexible analysis
farfield allows the user to designate
any of the layers beneath the surface
and above the subgrade as the design
layer in our example we want the design
layer to be
p209 to make this change in the grid
view click the P 209 layer then click
the button select as the design
layer note that in the grid view the red
arrow is now on the p29 layer indicating
that this is the design layer rerun the
thickness analysis by clicking the Run
button once the analysis is complete the
farfield design analysis indicates 4 in
p41 h
surface 5 in p401 h stabilized 10.5 in
p29 crush Aggregate and 12 in US user
defined on a subgrade with a CBR of
five last adjust a layer thickness to
construction thickness a ho inch or 1/2
in and then run a life/ compaction
analysis once the analysis is complete
review the section report and save as a
PDF for inclusion in the projects
Engineers
report in this flexible design analysis
we demonstrated how to add a userdefined
layer and how to change the analysis
layer these reference materials provide
further guidance on designing evaluating
and constructing airport Pavements
please visit
www.faa.gov airports to find these
documents this tool and other related
design tools for additional information
contact the faa's office of airports the
fa appreciates your interest safe
landing
