This is the final installment of my Dune rebinding project, and I've pulled out all the stops to really make this book something special! I'll be upgrading the plain endbands I wove in Part 2 with German braided leather endbands, which are in keeping with my original vision of mixing a variety of historic bookbinding styles into this binding. I then take on the challenge of hand-tooling the leather on all five panels of the wrap-around cover, incorporating some seriously Dune-inspired elements, and then embellish it with some genuine 24-carat gold leaf. And that conspicuous blank circle on the front flap? Well, that will be getting it's own special treatment with a hand-crafted medallion, so be sure to watch until the end!
Hello again everyone, I'm Dennis, welcome back to The Bindery.
In today's video we're going to finally finish this deluxe rebinding of Dune.
To get started today I want to work on upgrading these plain functional endbands that I sewed onto
the book in part 2. For that I'll be following the instructions in this book called Headbands
and how to work them. The style I'll be attempting is called a Germanic braided headband,
which is a structure that was regionally common in the late middle ages. I've been practicing
these off camera and I've made some annotations right in the book to help me remember the things
that I learned on the way. I will say right now that these are probably the most challenging
endbands that I've tackled to date and so this isn't going to be a tutorial. Instead just wish
me luck and hopefully these will turn out okay. Thankfully the materials and tools I'll need for
this structure are pretty straightforward. My main tool is going to be a sharp awl and I'll also need
two blunt needles with wide eyes that I'll use to weave this leather lacing. I tried a couple of
different ways to cut these laces but in the end I found that using scissors to cut around a circular
piece of leather was the most consistent. This is the same leather as I used for the bookmark so
everything's going to match. With the book held securely I'll roughly measure out about four feet
of lacing. In my practice runs I found that it takes a lot more lacing than you would think
and I don't want to run out part way through. To attach the lace to the needles I'd trim the ends
to a point so that I can slip it through the eye of the needle. This may not look particularly secure
but when put under tension the lace will bind against the eye of the needle and it's surprisingly
strong. I'll also give a light coating of beeswax to the leather to help it pull through the holes
a little bit easier. To begin I need to pierce a hole through the leather on the edge of the spine
just below the structural headband. And yes, jabbing a dirty big hole into something I've put
so much effort into is more than a little bit terrifying. But I've just got to commit to it
and work carefully. I push the awl through the leather a fair distance because I need a fairly
large hole to accept the leather lacing. This leaves plenty of room to pass the needle through
and at this stage drawing the leather lace through is pretty straightforward as well.
Though that'll change pretty quickly as the weaving gets going, which you'll see in a moment.
With the lace pulled through to the halfway point I bring the other end through the same hole from
the other side. With two double thicknesses of lacing passing through this hole now it's gotten
pretty tight. The authors of the book recommend using a pair of needle nose pliers to help pull
the leather lace through, so that's exactly what I'm going to do. Apologies for getting my hands
in the way of your view, but pulling like this puts a lot of strain onto the leather here so
I want to hold things in place to make sure I don't do any damage. Once that's successfully
pulled through I'll take up the slack leaving a small loop. With that first loop established I
now pierce the second hole to the right of the first one with the space roughly equivalent to
the width of the lacing. The biggest challenge, well one of the many challenges, in weaving this
endband is achieving the correct tension. It's a fine balance between pulling everything tight as
you go and leaving enough space to actually work the weave. You'll see what I mean in just a moment.
And this is where things start to get pretty complicated. The weave has to go back through
previous loops and around again to the outside. It's really easy to get things flipped around with
the lacing turned inside out or going under where it's supposed to be over or over where it's supposed
to be under. You get what I mean. As I said before I'm not trying to show you how to do this endband
because I barely understand how to do it myself. Eventually after four or five repetitions I start
to get a feel for the pattern and develop a rhythm and things go fairly smoothly after that.
As you can see the leather lacing is completely covering the structural endband that's underneath.
And as I work on this I realize why the German book binders of the late middle ages use this
structure. It ties the text block and the cover physically together thus adding an incredible
amount of strength to the part of the book that's subject to the greatest amount of wear.
Of course I think it looks particularly cool fitting in especially well with the style that
I've given to this binding. When I get to the other end I go back and refer to the instructions
once again to remind myself how to do the finishing wraps. Basically speaking the last
few loops get tucked in underneath previous wraps to secure them and then I simply trim them off
using a small pair of scissors. Well that went about as well as I could have hoped and seeing
it on the book now I'm really glad that I went to the effort to learn this style of endband.
I think it looks really good. Now I just need to do the other one and hopefully that'll turn
complete but I've got quite a lot more work to do to execute my full vision for this binding.
I've spent I don't know how many hours working on my design for the tooling for the cover
and I've gone through a lot of different iterations but this is the one that I finally
settled on. I've drawn it out full size on paper and then I used some thin tracing paper over top
to copy the design. The reason for that is so I can take the tracing paper and lay it on top of
the binding itself to work through to transfer the design before moving on to the full tooling.
To impress my design into the leather I'm going to be using a variety of brass finishing tools
some of which I've made myself but more on those in a little bit. Now I'll take my tracing paper
and cut out the individual panels for the back cover the edge flap and the front flap. To make
sure that these are positioned properly and don't move around I'm going to use a little bit of low
tack painter's tape to lightly attach them to the leather. As you can see my design takes
advantage of the fold over cover and follows around the entire outside of the book. Cutting
out the circle on the front flap template will help me to align it accurately. One of the main
tools I'm going to be using is this brass stylus that I made. It's got a narrow curved tip that in
practice is held much like a pen. Using a strip of book board as a straight edge I use the stylus
to work directly through the tracing paper going over the lines of my design to leave a faint
impression in the leather underneath. For these defined curves I switch over to these professionally
made finishing tools called gouges. I have an incomplete set of these in a variety of sizes
and I was careful to use only the ones that I had in creating the design. Where the stylus really
shows its worth is in these free form sand dune elements. Holding it just like a pen I can trace
over the gentle curves onto the leather. I work my way over the cover making final decisions on
the tooling as I go. I chose to leave out some of these sun rays that were part of the initial
design for example but in other places I feel that there's something lacking so I'll work in
other elements to those areas later. But the real benefit of working through the tracing paper is
that it allows me to accurately transfer my design onto the book. This technique will even work with
these more intricate tools as well. I'm going to use these to fill in larger areas with more of a
textured pattern which I laid out in a simple grid on the paper. They leave just enough of an impression
for me to see where I need to go over later. Once the basic pattern has been established I use my
little hot plate to warm the tools to make the final impressions. Using heated tools will ensure
that the impressions I make will not only be clear and crisp but dark and also permanent. I had to
experiment a little bit with temperatures because this leather has proven to be fairly unusual
in that it tools at a much lower temperature than what I'm accustomed to. In fact I found the ideal
temperature was about as if I'd left the tools sitting out in the sun. Just warm to the touch
but not quite uncomfortable. I found at this temperature the tools would make a clear dark
impression. At higher temperatures they had a tendency to stick to the leather which of course
is not ideal. As before I start with the straight lines to establish the edges of the design
which I really wanted to incorporate into the design but I felt that it needed a little
something extra to finish off the ends of the pattern. So I headed down to the workshop to make
a finial tool that matches up pretty well with the existing pattern. As I work I keep my original
design handy as a reference so that I can keep track of the pattern once I've moved beyond the
basic layout on the tracing paper. And here you can see why I like this particular tool because
by making multiple impressions end to end the pattern repeats creating a really pleasing sort
of bas-relief design. Once I finish working on the back surface of the cover I can turn my
attention to the spine following the same process to impress my design into the panels between the
raised bands. It's finally time for me to turn my attention to the front cover of the book
and for this I've decided to go all in with, you guessed it, a sandworm. Sandworms are at the heart
of Dune and since the aesthetic I'm going for is really reflected of the Fremen I really had no
choice but to incorporate shai hulud into the design. I'll use the same techniques as before
to transfer the design onto the cover and again the tracing paper template comes in handy, this
additional technique. As I was doing some tests for this project I discovered that this leather
could be compressed and polished to a dark chestnut color. So that's what I want to do to
the background around my sandworm to really make it stand out. I started this off just using my
stylus but I found the results to be less than satisfactory so I quickly popped down to the shop
to make this polishing tool. The teardrop shaped sole works really well for working around the
front edge of the front flap here blank but I did that deliberately because I want the design to line
up between the two surfaces. And with the front cover tooled I can now work on finishing up the
flap design so that all the different elements come together perfectly. I also take the time to
extend the tooling around the corners so that the design wraps all the way around the entire book.
With my original paper design fully achieved I can now use some of my other tools to fill
in some elements. I found that working on paper I could only use so much creativity
but now with the book almost fully realized I can use my artistic license to continue developing
the design until I'm happy with it. There are some areas that I chose to leave essentially blank for
the time being, partially because I didn't want to overdo it, but also if in the future I decide I
want to make some additions I'll have room to do that. There is one more feature that I've wanted
to incorporate into the tooling from the very start though and that's to incorporate some Fremen
glyphs along this line in the pattern. To do that I'm going to be following this Jacobse script that
developed for the most recent films. I of course don't have any custom tools for this script
so that means that I'm going to have to form each character individually using my stylus.
And if you're wondering what this script says but you can't read Jacobse,
which is a big milestone in achieving my vision for this book, but I'm not quite there yet. There
are two more things I really want to do to truly elevate this binding and for the first one I need
to prepare the leather in stages. I'll first apply a paste wash, which is a diluted version
of the same wheat paste that I used to attach the leather to the book. This will help to seal the
pores in the leather, which will create a smooth surface for the final decoration. And yes, I'm
aware that water is bad for sandworms, but in this case I think it'll be okay. Once the paste
wash is dry I continue the surface prep by adding a layer of gelatin to the tooled areas that I want
to highlight. Once the gelatin has dried I then apply two coats of a substance called glare,
which is basically just refined egg white and is the critical element for the type of decoration
that I'll be doing. I apply the glare over the dried gelatin layer onto the tooled areas that
I'll be working on. And finally it's time for me to let you in on what I've been hinting at,
which you may have already guessed, and that is genuine gold leaf. Gold leaf is not only an
traditional decorative material for books, but one that I think would definitely be in use in
the distant future of Arrakis. This is genuine 24 karat gold, and is less than a micron thick,
so it's extremely delicate and difficult to work with. Using my knife I'll cut the gold to size,
which will also make it easier to handle. I'll use a thin coat of Vaseline on the leather to
ensure that the gold stays put while I'm working on it. To pick up the gold I use a piece of cotton
wool which I've rubbed on my forehead. The tiny amount of natural oil from my skin is enough for
the gold to stick to, allowing me to pick it up. I can then press it in place, the gold sticking
more to the Vaseline than the cotton wool, thereby transferring it. In this way I'll apply enough of
the gold to cover all the areas that I want to work on. Once I've applied all the gold, I'll go
over all the impressions that I made earlier with the same tools, only this time I've heated them
to a higher temperature. I rock the tool left, right, up and down to ensure that I've made full
contact, while the heat of the tool sets the glare, permanently bonding the gold to the leather.
When done correctly the impressed gold surfaces should have a mirror shine, which really catches
the light. Once I've gone over all the tooling I need to remove the excess gold, and to do this
I'll use this gold rubber, which is made of natural crepe that's been softened with paraffin oil.
By rubbing it gently over the surface of the leather it will pick up any of the gold leaf
that hasn't stuck. This not only cleans up the excess gold, but traps it as well so it can be
recovered later. Gold may not be as valuable as spice, but it's still pretty expensive stuff.
The rubber will also pick up the gold from areas where it should have stuck but didn't,
and these I can go over again by applying more glare and more gold, then retooling. This is only
the second book I've ever done with gold after all, so I never expected it to turn out perfectly
on the first try. The gold rubber does a good job of picking up most of the excess leaf,
but to clear up any last stray bits I wipe the cover using lighter fluid, which also removes
any of the remaining Vaseline. So we've done the tooling, we've done the gold, but there's still
that conspicuous blank circle that you've been wondering about. Let me show you what I've made
to go there. If you don't recognize what this is, it's an engraving of the map of Arrakis,
more specifically the northern polar region. You may remember seeing this briefly way back
in part 1 of the series. I've made it to fit perfectly into the recess on the front flap,
and to hold it in place I made this engraved bezel to go around the perimeter.
The bezel has recesses that line up with the 6 slots you can see on the map,
which will allow me to use these copper cleats I made to hold the entire thing in place.
This map though is just a backdrop, but first let's take a quick sideline for me to show you
how I made it. Behind the scenes I've been practicing hand engraving, and I've finally
gotten to the point where I felt I could take on this design. Using a sharp graver and a small
hammer I carve my designs into the surface of the brass. The process is fairly easy to explain,
but much harder to execute. Once the engraving is done I cut out the pieces, clean them up with
files and sandpaper before doing a final patina treatment to achieve the desired look. And of
course the real centerpiece here is another sandworm. Just as the worms dominate the world
of Arrakis, my sandworm goes over top of the map of Dune, symbolically encompassing the entire world.
And because the coming and going of Shai-Hulud is so important to the Fremen,
this effigy will turn and pivot on a central point, a reflection of its dominion over the desert.
To attach the medallion I first need to pierce some holes in the flap. To do that I'm going to
use this narrow chisel. First I mark the leather through the piercings in the medallion itself,
and then with that removed I push the chisel all the way through the cover,
making enough room for my copper tabs to pass through to the other side. I then put the bezel
in place and push in the tabs. The bend points on the ends will hold the bezel and the baseplate in
place. Inside I trim the tabs to length using a block of wood as a gauge. Then mark and cut some
shallow recesses into the inside of the flap to allow the metal tabs to be bent down flat.
Using the back of my hammer I'll tap the tabs down. While this may look fairly extreme, my intent is
to create a tight clinch on the tabs to hold the medallion firmly in place. Or at least that's what
I had intended. So I'm having a ton of trouble trying to get these cleats to stay flat. I think
I've made an error in the way I folded them in. These inner tabs are folded opposite the way the
outside ones are, and I think what I need to do is to fold these over in the opposite direction so
that they pinch together, rather than this sort of seesaw effect. That means I'm going to have to
patch these holes that I made, but that's not too much of a problem. I didn't catch it on film, but
when I bent the tabs over in the other direction I actually broke one, because the metal had become
fatigued. So off-camera I took them back down to the shop, heat treated them to soften them, and
then made a replacement for the broken one. I'm glad I did all that though, because the tabs are
now really secure and below the surface of the inside of the flap, so they won't show through
once they're covered. To make the hole for the central pin that will hold down the sandworm,
I'll use my hand drill to make a small hole through to the other side, and then I'll put the sandworm
in place with the small copper pin that I made. That too gets bent over on the inside into a
corresponding recess. Finally, I'll use some small bits of greyboard cut to size and glued in place
to fill in the recesses. When those are dry, I trim away the excess with my paring knife,
and then sand the inside of the cover flap smooth. And now, at long last, we've come to the final
stage of this binding, and that's attaching the marbled papers that I made way back in episode 2.
I've kept them aside for just this moment, as well as a third piece which I'll use to cover
the two panels on the inside of the cover flap. Separated endpapers like these are called deblures,
and I wanted to make sure that they have a nice even border of leather around all four sides,
so I'll make a template first for each one. This way I'll be able to make sure my marbled
papers are cut precisely to size. I can't afford to make a mistake on those after all.
And here's another thing I've been waiting for for quite a while, and that's unwrapping the text
block of the book. I need to be able to see the papers on the inside to make sure the patterns
line up, and it's nice to see that the book is still there after all this time. Once I've got
marbled papers aligned where I want them, I'll fold up the edges around the template,
which will effectively mark where I need to cut them to size. I'll do that for all four pieces
before pasting them out. Here I'm using wheat starch paste, which is the same adhesive that
I used for the repairs in part 1. So while we watch me get those endpapers pasted in place,
I'll take a moment just to say thanks to everyone who's followed along with this series from the
beginning. This is a project I've wanted to take on for a very long time, and I'm glad that I've
been able to share it with all of you. The feedback I've gotten on this binding so far
has been nothing short of amazing, and so thank you to everyone who's commented on and liked the
videos, and of course subscribed to the channel. And of course a very special thank you to all
the contributors who have supported me directly either through PayPal or by buying me a coffee.
Your generosity has gone a long way in making this project possible.
I am, after all, a one-man show here, not only the bookbinder but also the cameraman,
video editor, and every other job that goes into producing these videos,
so I really do appreciate that extra support. If contributing to the channel sounds like
something you might like to do, you can find links on how to do so down in the video description.
Now, it looks like I've got those endpapers all done, so it's just a matter of weighing
them down to dry, and in the morning we'll get to see how this book has finally turned out.
So there it is, my version of Dune finally completed. I'm really happy with how it
turned out, and I hope you are too. It's been an incredible journey and I've learned a lot,
so thank you for joining me and sharing in the experience. I think now I'm going to sit down
and re-read this book, so until next time, I'm Dennis, and I'll see you in the next video.