🌺 How to make a SILVER PENDANT?

Jewelry Making
51 followers
Hello friends, how are you?
Today we are going to get out a little bit of the geometry and the exactitude, the caliber and the compass
and we are going to do a job that has to do more with the interpretation of the figures.
We are going to start with a rag, just taken out of the rag, it is 6 mm thick.
I have already drawn the silhouette of the hummingbird with a 0.0 saw.
We are going to go ahead and cut all the outline, taking as a fundamental care the very vertical cut,
not giving any kind of diagonal to the cut, a well lubricated cut.
We take firm with a hand press, with a half-cane file, using both parts,
we are going to start killing the edges of this rag, trying and starting to give this shape to the hummingbird.
The first pass of the file, as you can see, is quite thick,
since we are dedicating ourselves not only to fine-tune the body,
but only to kill edges and finish joining one part with the other.
On a chisel or anvil, we are going to hit with a firm hammer, combing the material,
looking for the glue to spread to the sides, also fine-tuning.
With the same half-cane file, we join glue with body,
always taking into account the same idea of generating this aerodynamic body of the hummingbird.
This is a job that does not have much technical explanation,
because I insist, it has more to do with the interpretation of a figure.
We join the head, finally, to the curved lines, leaving the conical peak of the hummingbird for the end.
A pass of esmeril with the wheel, we take out all the file,
and we mark the center of the peak, making it conical,
and we are going to cut it with a 0-0 saw, leaving a margin so that in the future we can finish it.
A plane on the back with the same file,
we take with a compass, the only moment in which the compass appears,
and we are going to mark two rectangles to go on to wedge them.
We rectify the tips with file,
and with the same file we are going to give it a small diagonal that will give us the degree of inclination of the wings.
As I said, completely at ease, here in this work there are no rules.
The wings welders can make a kind of fit,
in this case I am going to weld them in the air, but it is a matter of habit and years of welding and being able to do it this way,
but they could easily be held by making a kind of fit inside the body.
We sew to pass to the second wing,
and previously we are going to make a very well known protection with corrector,
this is going to protect us from the second weld, we do not risk the weld of the first wing.
We already lift the cloth with the wing and we go directly to the body.
We stay in salts as always,
with indereble we throw the diagonals of the wings to go to wedge them.
With a mouse tail we join the internal part of the wings as well as the external ones to the body.
We continue drawing with indereble and with an umbrella strawberry,
you can mark these cuts that can easily be done with a buril,
a very free technical work in which you can handle several options in terms of files,
all kinds of tools that can achieve the same or similar result,
it is a job more to enjoy than to speak.
With the same strawberry I hit and generate this feather effect.
As in any piece we go from thick emery to fine emery,
and we are going to make the ring so that it becomes a wedge,
it will be under the wing, attached to the body, so that the hummingbird is on the side.
We protect again the only two welds that the piece has,
and in this part the film fell asleep and the weld will not appear.
We square the center of the head to mark the two eyes,
and with the steel tip we mark the seat for the wedge.
We are going to use 1.5 mm cubic stones,
therefore we start with a 1 mm wedge.
Round strawberry,
and from a round strawberry we are going to pass an umbrella strawberry,
giving just the right measure of the stone,
leaving it below, the waist below the level,
so that you can make a flush, a level wedge.
I do not hit or hold in any way other than with my hands,
this is a fairly simple and fast wedge.
And in this case, with the same tip that I marked the seat for the wedge,
is with which I close the material on the waist.
Finally we reached the conical peak of the hummingbird,
this is a species of hummingbird,
investigating on this I find that there are more than 300 species of hummingbird,
so well, this is one of them.
It has a small concavity at the peak,
and it is a little longer.
We are going to leave the peak with that filed texture,
only as an aesthetic detail.
We go to the polisher, brush with Tripoli paste,
and white high-gloss paste for the rag.
After polishing,
before going to the washing machine,
we are going to retouch again with file,
the peak to emphasize the texture.
We wash,
and the hummingbird is over.
Friends, I hope you liked it, I hope you enjoy it,
since this is a work, as I said, of interpretation,
and to enjoy, to those who like it,
and not much more.
Thank you very much and see you in the next video.
Goodbye.
