Screw-Post Photo Album - Basic Design // Adventures in Bookbinding

Sparky Deal
161 followers
In this video I make a basic screw-post guarded album, suitable for items like photos or scrap booking. It is based on the specifications in Arthur Johnson's The Thames and Hudson Manual of Bookbinding. There are many other variation of these which I will explore in the future.
#Sparky Deal #bookbinding #DASBookbinding
In today's video, I'm going to make one of the simplest versions of the Screw Post album.
I'll explore variations of Screw Post albums in future videos.
One of the important features of this book is that it's guarded.
After binding, it's wedge-shaped with the spine thicker than the fore edge.
Spaces are put between the pages, which allow things like photos to be added, and eventually the boards will end up parallel.
Arthur Johnson shows four variations of guarding and four variations of covering.
For this video, I'll use the first guarding method and the cover design shown on the facing page, which wasn't listed in the four.
It's usual to use thicker material for albums like this.
I'm going to use 300 GSM or 10 point cardstock.
I'm using a high quality acid-free Bristol card.
The size of the leaves is sort of determined by the size of the sheets it comes in.
I didn't want waste, and I divided the sheet up evenly in a way that would be suitable for 4 by 6 and 5 by 7 inch photos, two common photo sizes.
If you have a board cutter, the cutting can be sped up a lot.
And this card can be cut with a guillotine too, as it's not hard on blades like greyboard.
Most people don't have access to these, so I'll cut it by hand to demonstrate that it's possible and the results are great.
Towards the end, I did keep glancing at the camera, which was next to my guillotine, and I was tempted to cheat.
In Johnson's first guarding mechanism, the guard, which is the name we're using for the spacer, is a separate piece of card of the same thickness.
My card is wide enough that I can cut this off each piece.
It also means when I do the second guarding method, they'll be the same size book.
I'm cutting the guards to 25 millimeters wide, which is conveniently the width of my ruler.
Guarding is also the name used for reinforcing.
When repairing the spine folds of old books, this is also called guarding.
I'm using screw posts, which are 25 millimeters or an inch long.
I'm going to do enough sheets to fit the screw posts.
These are 5 millimeters thick.
4 or 5 millimeters thick, I think, are the ideal thickness for bookbinding.
They have many other applications and come in different thicknesses.
They also come in different lengths, and you can even add extenders.
You may buy the screws to match your project.
Maybe your catalog expands, in which case you can even make your book thicker.
Another common name for screw posts is Chicago screws.
According to the Internet, they were first invented by the Chicago Screw Company in 1872.
That's a simple enough explanation for this name.
I've mostly known them as Chicago screws, but screw posts seems more descriptive and more appropriate and nicer than
a couple of the other names used.
Chicago is a wonderful city, so I'll keep calling them Chicago screws in everyday use, but use screw posts in videos for
clarity. To punch the holes, I'm going to use a template.
I'll make this from scrap card.
I want the holes centered on the guard piece and closer to the ends, but not right at the end.
In my prototype, I came in 30 millimeters.
Since this book is larger at 182 millimeters wide, I came in 35 millimeters.
I made a simple jig with some thin pieces of wood and grayboard to make punching the holes easier and faster.
Because the spine doesn't flex and can't contribute to the opening mechanism of the album, it's important that the grain
direction is head to tail as the flexing or drape of the card is the main contributor to its opening ability.
And because it is a cardstock which drapes much less than paper, it is usual for these to be made in a landscape
format. I guess this also matches the format of most photos.
To speed up the hole punching, I experimented to see how many I could punch at a time.
Two was the answer.
I'm using a Japanese screw punch with a 5 millimeter bit to make the holes.
In a commercial bindery, a paper drill would be used and they'd be drilled as a single stack.
A leather hole punch could also be used.
And yes, I do have a paper drill, but you probably don't.
And I enjoy using my Japanese screw punch.
This album is part of a class of work known as loose leaf work.
Johnson says this about it.
Loose leaf work is a minor branch of craft bookbinding.
It is a cheap, quick method of holding sheets together in a protective cover with some degree of security.
There are some advantages.
Sheets can be removed and others inserted without difficulty.
The point about being able to be removed, changed and added is a very desirable feature.
This is why it's often used for manuals, catalogs and menus.
When used for this reason, the guards aren't needed.
The first example Johnson describes is just this case.
And this is the covering style I'm demonstrating, though he suggests using a drawstring instead of screw posts.
This album has two separate boards.
In this version, the backboard is a solid piece, while the front board has a hinge, which hinges at the edge of the
guards. You could put a hinge in the backboard too, which might open a bit better.
But then the backboard tends to lift up, which I'd rather avoid.
These albums tend to have large squares.
I decide to use 5 millimeter squares at the head, tail, fore edge and spine.
Adding the 5 millimeters at the spine was a mistake, but it still works.
And I'll explain in a bit.
The main thing is that I need to cut two pieces of board, two times the square larger in both directions than the card.
I measure the card again and add 10 millimeters for width and height and cut the board.
The front board is made of two pieces, a narrow piece at the spine and the wide piece.
If there was no square at the spine, the spine piece should be the width of the guards.
This was my original plan, and so this is what I cut.
If there is a spine square, the width of the spine piece should be this square added to the width to give 30 millimeters
instead of 25.
I didn't, you should.
Then a piece the width of the hinge is cut off the main piece of board.
Johnson suggests 8 millimeters, which from experience I know works well with 2 to 3 millimeter board and heavier book
cloth. I'm using 2.4 millimeter gray board and Chelsea book cloth.
Johnson says to keep the 8 millimeter wide piece so it can be used to space the boards.
I like to add 1 millimeter and cut a new piece 9 millimeters wide.
I like to work the cloth down into the hinge after gluing, and this draws the boards together a bit.
The extra 1 millimeter compensates for this.
I make the turn ins 20 millimeters, and the covering cloth for the backboard is simply large enough that I can roughly
position the board and trim the turn ins to 20 millimeters later.
The front piece is slightly different.
The spine turn in covers across the narrow piece of board and the hinge.
For the guard width of 25 millimeters, a 60 millimeter turn in works well.
And so I make it about 70 millimeters so I can trim it after applying it.
Covering the backboard is straightforward.
Glue out the cloth, apply the board, trim the turn ins to width, miter the corners, glue the turn ins and turn in head and
tail, then fore edge and spine.
The front board is slightly more involved.
Glue out the cloth for both pieces and apply the large piece and then the small spine piece, positioning it with the
9 millimeter wide spacer.
The head, tail and fore edge turn ins can then be trimmed.
But the spine turn in needs to be marked as per Johnson's instructions.
Draw a line out from the board 3 millimeters narrower than the width of the board.
Then mark the corner miters.
Cut along the corner miter line until it hits the lines perpendicular to the end of the boards.
Trim out along these lines.
Now the turn ins can be glued.
Head, tail and fore edge and finally the spine edge.
Work the cloth down into the hinge from the front.
It's a good idea to press the boards for a few hours now.
I put them between blotters to help draw the moisture out.
I added a layer of remade between the boards and the blotters to stop the blotters sticking to any stray glue.
If you're careful, this isn't needed.
I line the inside of the boards with some nice handmade paper from Tasmania.
This paper is made by the excellently named Darren at Creative Papers in northern Tasmania.
I bought a selection of these different colors and different weights in A3 and I highly recommend you do the same.
Australia needs handmade paper and we should all support Darren's efforts.
In Johnson's first guarding method, he scores the card just outside the edge of the guard.
I use a scoring jig to score each sheet 30 millimeters from the spine edge.
The scoring jig is straightforward.
Rather than trying to explain it in this video, I'll make a little standalone video about it.
You don't need this jig.
You can just score the card with a ruler and bone folder.
Finally, it's time to make the holes in the boards.
I tried making a template to do this, but found just using one of the pieces of card was the most accurate approach.
Position it so the squares are correct and make the holes through the holes in the card.
Do the backboard first and then use this to start the holes in the front board.
Don't try and get all the way through both boards.
It's just too thick.
This is when I realized my mistake, making the spine board piece too thin for a square at the spine.
Don't use the square at the spine and this won't be an issue.
The album still functions fine.
The screws just aren't centered in the spine board strip.
Now it's just a matter of putting it all together.
I found one piece of card that wouldn't go in straight.
Luckily, it wasn't needed.
Maybe making an extra couple just in case would be a good idea.
I also cut an extra spine strip card so I could start and finish with one of these.
The just in case pieces reminded me of a running joke we had during my first winter in Antarctica at Casey Station.
These bases had to be self-sufficient for long periods of time.
The winter period for Casey, when it was completely isolated, used to be 8 months.
When something broke, it was common to store the old broken pieces in case you ran out of spares and were forced to
salvage enough bits from broken items to make a functioning replacement.
We also needed sufficient contingency in case of emergencies.
The unintended consequence was that often there was no space to store new replacement parts because of all the broken
junk, and you might run out of something but still have it in stock, but not be allowed to use it because it was
contingency reserve.
We used to say that this stuff was for the mystery crew member known as Justin, short for just in case.
These albums are straightforward to make and suitable for people fairly new to bookbinding.
But they do take a bit of time and can drag on a bit.
I thought I'd never get this video finished.
I will explore some of the more interesting versions in the future, such as ones where the screws are hidden.
And I will eventually do a sewn guarded album, which a lot of people have requested.
If you're into your retro film photography, here's the perfect way to store your photos.
I'm sure you'll be making an album this week.
As always, I really appreciate you hitting the big thumbs up button.
If you're able and want to, you can support the making of more videos like this through Patreon or with a one off
contribution. And the details are in the description below.
If you want to be notified of my future videos, please hit the subscribe button.
Until next time, cheerio.
