DIY BIKIN LIGHTSTICK BLACKPINK YANG 70% MIRIP!

Today I will teach you how to make a blackpink ltick that lights up and is 70% similar to the original. The materials are just using the template book here which contains patterns for making the item. So you just cut and paste and don't need to measure anymore, okay now. Jump. Let's just make it to make the Black Pink plastic at the beginning. There will be three parts. The first is to make the head of the stick in the shape of a heart. The second is to make the connection between the hearts. The third is to make the stick. Please watch this video and follow all the steps from start to finish in order. Don't be too busy cutting the pattern first, guys. Then you'll be confused . Then there's a tip for cutting the pattern, namely by following the line with the white border. Here, guys, this one also has a white border, right. Cut the line. OK, cut it on the inside line, not the white border. Well, if there is one. there's a line but there's no white border. Guys, don't cut it. If you look at page 4, there are letters, guys. This means you have to connect the letters a with A, so later you cut the pattern first and then you connect it. This is a. This is a. This is connected so it will be long. look, there's a and a, b, and B, don't turn it over, don't go to a, then B, then A, again, B, this one is n't, guys, it's already destroyed, the lightsck is black and pink, well, you have to pay attention to this first page because it contains materials that must be prepared before starting. it's ready, you can check it like this so you don't miss it. And now you're good to go. First, we tear out pages 1, 2 and 3, then cut out all the patterns, some of the hearts, some of the hearts need to be cut in the middle, guys, basically there will be a total of 12 hearts, two with writing, two plain and eight. If you have successfully cut all the holes, we glue and stack the hearts. The heart with the writing on it is paired with a plain heart, while the one with the hole remains in a pair with the hole. If it has been glued in pairs, there will be four hearts with holes and two hearts with writing. Next is to cut out the pattern on it. Pages 4 and 5 later we will connect this pattern according to the letters, there are a and a b and [Music] P Here I'm connecting guys, continue when it's connected we fold the tongue and start to shape it into a heart. The method is by gluing the ends like this. OK, now you should have it. two left heart walls and two right heart walls but we will focus on one side first we will stick this wall to the heart with the writing on it and the other to the heart with a hole without the logo. Now we will prepare this very light lamp which I have provided in the package. Guys, color the lights one by one with a red marker. Once you have finished coloring, turn this part of the light to form the letter O [Music] then insert the light through the hole, starting from the heart with no walls and then to the heart with the hole and walls, now it's time for us to glue the lights, starting from This heart without a hole must be glued in the corners of the heart and one heart contains five bulbs, there's no need for more. How to glue the shot. There 's nothing special as long as the el is enough. So, if we fold it in, the tongue is glued and then closed with the heart with the hole. and the wall, aka the middle heart. Well, later we will attach the light again to the middle heart, the steps are the same, guys, it's done, we'll immediately cover it with the last heart, so make the head of the lightstick. The other side is also the same as before, okay, step 18, let's turn it make one wire so it's neat, guys, and put these two buttons together, one facing the front, the other facing the back, let's go, tear off pages 6 and 7, cut the pattern for the top of the stick first, don't forget to cut the gap because we're going to tuck the wire into the gap. Glue it to make it secure from The heart to the stick joint is also glued [Music] now the last step is just to make the stick, the pattern is on the en page, guys, then to make it even sturdier, we want to put another layer on the inside of the stick, so it's like double two, guys [Music] if it's already thick, just go straight Roll it up, stick the ends together and cover the bottom of the stick using the pattern on page 6. Yes, it looks like a circle like this. OK, it's time to insert the light button into the discure stick. Use hot glue on the top and let's give it a button so we know where to press it. [Music] Divide it into two. make one at the front and the other at the back [Music] so when gluing it to the stick, you first feel around for the position of the button, when you find it, then glue it, for example, I was fumbling around and then I was like Oh yeah, here and here, then stick it [Music] that's it, here's the DIY l blackpink stick that Iren made to turn it on. There are two buttons, different from the original, only one button, OK [Music] guys, this is a comparison of the original ltick with my diy ltick. In terms of shape, it's more or less the same, guys, but this is actually I made another version, this is the latest version, but in terms of details, it is still very similar, yes, this has a dose of Black Pink. This one is made by me so there is an Iren Su for the buttons. There are two that I made, one in front, one in back. like this, there's only one and the original one has a middle detail while the DIY one also has this so that's how to make a DIY Black Pink lift stick. I hope you like it. For example, if you like it, you can try it on my other iw plastics, there's nctity BTS and twice. You can check the video in this playlist. OK, guys, see you later, bye