【solidworks】特殊特徵:彎曲 論筆直到掰彎最速|到底是什麼樣的狠角色|可以一下掰直、一下掰彎 這樣軟中帶勁

模艦隊 雷系教師阿儒
1粉絲
彎的東西不大容易建,每次建都是絞盡腦汁 ((淚流滿面
一樣也是設變不得的案例
上一次彎曲的影片真的大受歡迎
阿儒很驚訝 所以今晚7點 再次隆重介紹「彎曲」
測試看看是不是真的受歡迎
到底是什麼樣的狠角色
可以讓人一下掰直、一下掰彎的 ((安導:什麼東西辣 -.-
實在是太恐怖了...
還不快來看看嗎? 到底是誰這麼帥、帥到這麼殺的
還沒有加入模艦隊的朋友在哪裡?
與阿儒一起成為帥度爆表的狠角色吧
還請大家多多給予支持~ 留言給阿儒寶貴的建議 ^A^/
歡迎按讚、訂閱或分享阿儒的頻道喔!
#模艦隊雷系教師阿儒 #solidworks #onshape #3d建模 #3dmodeling #三大建模觀
I think the most commonly used ones are bending and twisting.
Why? I’ll click on it and you’ll understand❗️
Hi, everyone, Welcome to my channel, I am Aru.
The pipe is in straight pipe condition.
When you want to start deformation (bending), remember to do the configurations first❕
In this state, we will do the deformation.
insertion -> Features -> Bending
Tap the part you want to bend.
Tells it that I want to bend it 90 degrees.
But you will find one thing: it is also bent here and everything is in a bent state 😂
⚠️But there is a problem when everything is bent...
If what you do today is Whether it is round pipes, square pipes, etc.,
Suppose you want to connect another pipe to the front here,
But there's no way to make a series connection at the moment because the front is bent.
So you have to remember that there is a trimming plane 1 and trimming plane 2 here,
then my trimming plane 2 is 50mm, so you can retract 50mm inward.
Trimming plane 1 is 43mm,
then it will be a "straight line" from the other side all the way down to 43 mm!
Inside, there's a 90-degree bend.
The same goes for the right side. Push inward 50mm from the edge and then start to bend.
But you don’t have to use 90 degrees.
It can be 45 degrees or 75 degrees or 60 degrees, depending on how you design it❗️
This is state 1 (bending), so I want to demonstrate the other ones to you by the way😄
Make sure you subscribe if you haven’t subscribed already
I will first make the second configuration (V2) and
do the twisting in the V2 state!
There is a twist option in bending, of course there are others
, but I think the most commonly used ones are bending and twisting❕
Why? I’ll click on it and you’ll understand😉
It’s the same on the left and right. I’ll turn it 30 degrees to show it to you.
It looks like this: You can wring out your wet towel in Solidworks🤣
Doesn't it look like that?
Of course, you can do the same thing as before.
Have you discovered anything?
Its left and right sides are not twisted,
but the middle is rotated 30 degrees‼ ️
This is a very interesting part.
Its left and right sides can be connected to other pipes, and only the middle will be deformed.
Can you use this form to make changes when designing products? Of course !
So today I will demonstrate two modes of bending.
Curious about how I got the dimensions at the beginning?
This is how I assumed it.
When actually designing, remember to set it according to the design requirements 😉
That's roughly it.
Thank you for watching.
If you like our video, please like and click on the button below to subscribe!
See you in the next video.
